Vodavi Starplus Triad S Description Manual

							System Parameters Programming
Additional System Timers2-19
Pulse Dial Inter-Digit Timer
Programming Steps
1Press the PULSE DIAL I/D TIMER flexible button (FLASH 02, button #5). The following
message displays:
INT DIGIT PULSE300-600
300
\
2Enter a 3-digit timer value on the dial pad that corresponds to 300-600 ms.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
This governs the inter-digit time of the Pulse Dial Digits. By default, the Pulse Dial Ring Timer is set for 300
ms and is variable from 300-600 ms.DTMF On/Off Time Operation
Programming Steps
tPress the DTMF TIME OPERATION flexible button (FLASH 02. button #6). The
following message displays:
I
DTMF ON/OFF TIME100-999100/100I
2Enter a 3-digit value (100-999) on the dial pad for the DTMF on and off times.
3Press HOLD to save the entry. A A confirmation tone is heard.
Description
This feature lets the installer select the DTMF on/off time on a system-wide basis. This lets the installer
customize the system for certain applications that require more than the standard DTMF time of 
100ms on
and 
1OOms off. By default, the DTMF Time Operation is set for 100 ms on and 100 ms off.
STARPLUS Triad-S System Programming ManualIssue I- December 1998 
						

							System Parameters Programming
System Features 1 Programming
System Features 1 Programming
Programming Steps
If the system is in the programming mode, continue using the program codes, If starting to program here,
enter the programming mode.
1Press FLASH and dial [05]. The following message displays:
I
SYSTEM FEATURES 1
ENTER BUTTON NUMBER
I
Description
This section describes the procedures and steps necessary to program System Features in the System
Features programming area. The buttons on the digital terminal are illustrated on the following page:
Issue 1 - December 1998S JARPLLJS Triad-S System Programming Manual 
						

							System Parameters ProgrammingSystem Features 1 ProgrammingATTNHOLDEXTERNAL
EXECUTIVE
OVERRIDE
+% EiQIPAGE WARN
TONE
*15GROUP
LISTENING
#%19CALL QUALIFIER
TONE OPTION
+I#-PREFERENCE
NIGHT RING
*- 113BACKGROUND
MUSICLCR ENABLE
%16 #mIDLE SPEAKERCALL COST
MODEDISPLAYOVERRIDE
*mACCOUNT
CODES
%IsMUSIC ON HOLD
Program
FlexFeatureDefault
CodeButton
(after initialization)
I,I
System Features 1:
FLASH 05
1Attendant Override
2Hold Preference
3External Night Ring
4Executive Warning
5Page Warning Tone
6Background Music
7Least Cost Routing
8Account Code
9Group Listening
IOIdle Speaker Mode
11Call Cost Display Feature
12Music On Hold
13Call Qualifier Tone Option
Disabled
System
DisabledEnabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
DisabledEnabled
DisabledTable 2-3: System Features 1 Defaults
I
STARPLUS Triad-S System Programming Manual
Issue 7 - December 7998 
						

							System Parameters Programming
System Features 1 Programming
Attendant Override
Programming Steps
IPress the ATTN OVERRIDE flexible button (FLASH 05, button #I).
2Enter a l-digit value (O-l) that corresponds with the following entries:
[0] = Disabled
[I] = Enabled
ATTENDANT OVERRIDEo-1DISABLED
3Press HOLD to save the entry. A confirmation tone is heard.
Description
When this feature is enabled, it lets the attendant override a busy station or a station in DND. By default,
Attendant Override is disabled.Attendant Override functions ONLY when the Attendant station is 
QS-signed a flex button designated us Attendant Override.
Hold Preference
Programming StepsIPress the HOLD PREF flexible button (FLASH 05, button 
#2).
2Enter a l-digit value (O-l) that corresponds with the following entries:
[0] = Exclusive Hold
[I] = System Hold
HOLDM;RENCEO-l
t
3Press HOLD to save the entry. A confirmation tone is heard.
Issue 7 - December 1998STARPLUS Triad-S System Programming Manual,::.: :.. :..,1. -.. ,.._ . ,. . . .=:. 
						

							System Parameters Programming
System Features 1 Programming2-23
Description
The system may be programmed to have Exclusive or System Hold preferred. If Exclusive Hold is preferred,
the user presses HOLD once for Exclusive Hold and twice for System Hold. If System Hold is preferred, the
user presses HOLD once for System Hold and twice for Exclusive Hold. Refer to System Timer programming
for System and Exclusive Hold recall times. By default, Hold Preference is System Hold.
External Night Ring
Programming Steps
1Press the EXT NIGHT RING flexible button (FLASH 05. button #3).
2Enter a l-digit value (O-l) that corresponds with the following entries:
[0] = Disabled
[I] = Enabled
I
EXTERNAL NIGHT RINGO-l
DISABLEDI
3Press HOLD to save the entry. A confirmation tone is heard.
Description
When this feature is set to yes, it activates external night ring whichproduces a tone that is sent
ouer all externalpage groups. When outside lines are marked UNA, ringing activates a tone over
external paging when an incoming call occurs on those lines during night service. By default, External Night
Ring is disabled.
Executive Override Warning Tone
Programming StepsIPress the EXEC OVER WARN TONE flexible button (FLASH 05, button 
#4).
2Enter a l-digit value (O-l) that corresponds with the following entries:
[0] = Disabled
[I] = Enabled
EXEWME;ARNINGO-l
STARPLUS Triad-S System Programming ManualIssue I- December 1998 
						

							2-24System Parameters Programming
S,ystem Features 1 Programming
3Press HOLD to save the entry. A confirmation tone is heard.
Description
This option enables Executive stations to override and barge-in on other key sets engaged in conversation
on a CO line. Prior to actual cut through of the third party, a warning tone is presented to all parties
notifying them of the barge-in. This warning tone, however, is a programmable option on a system-wide
basis, that either enables or disables the tone. When the tone is disabled, no audible signal is presented to
the parties to signal the barge-in. By default, Executive Override Warning Tone is enabled.Use of this feature when the Executive Override Warning Tone is disabled
may be interpreted as a violation of federal, state, or local laws, and an
invasion of privacy. Check applicable laws in your area before intruding on
calls using this feature.
A change in volume may occur on the CO line or intercom call after the
barge-in occurs. This feature also affects ACD Supervisor Barge-in warn-
ing tone.
Page Warning Tone
Programming StepsIPress the PAGE WARN TONE flexible button (FLASH 05, button 
#5).
zEnter a l-digit value (O-l) that corresponds with the following entries:
[0] = Disabled
[I] = Enabled
I
PAGE WARNING TONEo-1ENABLEDI
sPress HOLD to save the entry, A confirmation tone is heard.
Description
Determines whether a page warning tone sounds over the Key Telephone speakers or external paging
speakers, prior to a page announcement. By default, Page Warning Tone is enabled.
issue 1 - December 1998STARPLUs Triad-S System Programming Manual 
						

							System Parameters Programming
System Features 1 Programming2-25
Background Music
Programming Steps
T~::*$.
f&,‘.::”1;...Press the BACKGROUND MUSIC flexible button (FLASH 05. button #6).
zEnter a l-digit value (O-l) that corresponds with the following entries:
[0] = Disabled
[I] = Enabled
BACKGROUND MUSICO-lENABLED
3Press HOLD to save the entry. A confirmation tone is heard.
Description
The system can be programmed to let stations activate their Background Music, in addition to Music-On-
Hold. A music source must be connected to the BGM/MOH connector on the MISU. By default, the
Background Music channel is enabled.
Least Cost Routing (LCR)
Programming Steps
IPress the LCR ENABLE flexible button (FLASH 05, button #7).
zEnter a l-digit value (O-l) that corresponds with the following entries:
[ 0 ] = Disabled[I] = Enabled
.
LEAST COST ROUTINGO-lDISABLED
sPress HOLD to save the entry. A confirmation tone is heard.
Description
If Least Cost Routing is used, it must be enabled here. Before enabling LCR, refer to the Least Cost Routing
section (Flash 
75) and programming tables (Product Description Manual - Appendix C). When the tables are
programmed, you may then enable LCR for the system. After system initialization, a default LCR database is
loaded into the LCR section of memory. By default, LCR is disabled.
STARPLUS Triad-S System Programming ManualIssue I- December 1998 
						

							.
System Parameters Programming
System Features 1 ProgrammingAccount Codes 
- Forced
Programming StepsIPress ACCOUNT CODES flexible button (FLASH 05, button 
#8) to determine whether
the use of Account Codes is forced or optional.
2Enter a l-digit value (O-l) that corresponds with the following entries:
[O] = Disabled
[I] = Enabled
FORCED ACCOUNT CODEo-1DISABLED
3Press HOLD to save the entry. A confirmation tone is heard.
Description
The system can force the use of account codes on all restricted calls. If forced account code option is
enabled, a station’s Class of Service is upgraded to day 
COSl, night COSl, when the account code is entered.
If forced account code option is disabled, a station’s Class of Service is not upgraded but the account code
continues to be part of the SMDR record. By default, the use of account codes is optional.
Group Listening
Programming Steps
1Press the GROUP LISTENING flexible button (FLASH 05, button #9).
2Enter a l-digit value (O-l) that corresponds with the following entries:
[0] = Disabled
[I] = Enabled
I
GROUP LISTENINGO-lDISABLED
L
3Press HOLD to save the entry. A confirmation tone is heard.
Description
All digital key terminals have built-in speakerphones. Station users may use the speaker to monitor a call
while using the handset to converse with the outside party. This enables other people in the room to listenIssue I- December 1998
STARPLUS Triad-S System Programming Manual 
						

							System Parameters Programming
System Features 1 Programming2-27
to both parties in the conversation. Group listening is unavailable when the station is in the headset mode, By
default, Group Listening is disabled.
y--,
c-2; Idle Speaker Mode
Programming Steps
IPress the IDLE SPEAKER MODE flexible button (FLASH 05, button #IO).
2Enter a l-digit value (O-l) that corresponds with the following entries:
[0] = First digit dialed is Heard (Disabled)
[I] = First digit dialed is Muted (Enabled)
IDLE SPEAKER MODEO-lDISABLED
3Press HOLD to save the entry. A confirmation tone is heard.
Description
The Idle Speaker Mode feature determines whether the first digit dialed is heard over the digital key terminal
speaker. This feature can be enabled or disabled on a system-wide basis. By default, this mode is disabled.
Call Cost Display Feature
Programming Steps
IPress the CALL COST DISPLAY flexible button (FLASH 05, button #ll).
2Enter a l-digit value (O-l) that corresponds with the following entries:
[0] = Disabled
[I] = Enabled
.
CALL COST DISPLAYo-1A“.-. .i_
6.
DISABLED:-.2:xpz;
3Press HOLD to save the entry. A confirmation tone is heard.
STARPLUS Triad-S Sysfem Programming Manual
Issue I- December 1998 
						

							.2-28
System Parameters Programming
System Features 1 Programming
Description
The Call Cost Display Feature lets a user view the approximate cost of each call made. This approximate cost
also prints as part of the SMDR record. The Call Cost Display replaces the call duration display when a call is
made using LCR. Cost information is programmable in LCR Flash 75. This enables the user to program four
separate costs based on the time of day. Costs entered in the tables are costs for one minute, however, costs
are calculated using 
l/lOth of a minute value. These costs are rounded down and based on the call start
time, even if the call extends into a different time period. The SMDR printout contains a cost calculated
using 
l/lOth of a minute increment, however the station display updates approximately every 30 seconds.
The user 
must use LCR to get the call cost display. By default, the Call Cost Display feature is disabled.
Music On Hold
Programming Steps
1Press the MUSIC ON HOLD flexible button (FLASH 05, button #12). This feature
toggles on and off each time the button is pressed. The display updates with each
toggle.
[0] = Disabled
[I] = Enabled
MUSICOOL;;LDO-l
2Press HOLD to save the entry. A confirmation tone is heard.
Description
When connected to the system, a music source provides music to all lines on Hold, parked calls,
transferred calls and calls waiting to be answered by Automatic Call Distribution (ACD) or Uniform Call
Distribution (UCD). This feature is allowed or denied on a system-wide basis in programming. By default,
Music-On-Hold is enabled.
Call Qualifier Tone Option
Programming Steps
IPress the CALL QUAL TONE OPTION flexible button (FLASH 05, button #13).
2Enter a l-digit value (O-l) that corresponds with the following entries:
[0] = Disabled
Issue I- December 1998S JARPLUS Triad-S System Programming Manual
::. 7 ; ‘.,.... ,._. -,i-l ,... c