Vodavi Starplus Triad S Description Manual

							System Parameters Programming
System Features 2 Programming[I] = Enabled
CALL QUALIFIER TONEo-1DISABLED
3Press HOLD to save the entry. A confirmation tone is heard.
Description
This feature is associated with the ACD Call Qualifier code and determines if a confirmation tone is heard
after the ACD Call Qualifier code is dialed. If programmed, the confirmation tone is heard through the key set
speaker. This feature provides up to four digits for the ACD SMDR reporting functions that are compatible
with the Basic ACD software package. This feature permits entry of up to twelve digits, By default, the Call
Qualification Confirmation tone is disabled.
System Features 2 Programming
Programming Steps
If the system is in the programming mode, continue using the program codes. If starting to program here,
enter the programming mode.
tPress FLASH and dial [06]. The following message displays:
I
SYSTEM FEATURES 2
ENTER BUTTON NUMBER
I
Description
This section describes the procedures and steps necessary to program System Features in System Features
programming area. The buttons on the digital terminal are illustrated on the following page:
STARPLUS Triad-S System Programming Manual
Issue I - December 1998 
						

							2-30System Parameters Programming
System Features 2 ProgrammingPRIVACY
RELEASE TONE
*llEXT DAY
RINGINGCO RING TONEVERIFIED ACCT
CODES
+- *rs--iq
ACD/UCDOVERFLOWDIRECT
STA FWDTRANSFERCALL FWD
DISPLAY
STATUS
*EzRlSTATION ID
LOCK
LCR CALL
PROGRESSONE-TOUCH
RCD WARNING
RINGBACK ON
TRANSFER
*ill17$1
16HI
12074
VI
ProgramFlex
FeatureDefault
CodeButton
(after initialization)FLASH 06
r
1Privacy Release Tone
Enabled
2CO Ring Tone
Enabled
3Verified Account Codes
Disabled
4Call Forward Display Status
Enabled
5External Day Ringing
Disabled
6ACDNCD Overflow Sta Fwd
Disabled
7Direct Transfer
Enabled
8Station ID Lock
Disabled
9LCR Call Progress
Enabled
10One-Touch Record Warning ToneEnabled
11Rlngback on Transfer
Disabled
Lssue I- December 1998Table 2-4: System Features 2 DefaultsSTARPLUS Triad-S System Programming Manual
,:-‘!‘. ..+.:I .., -.l..i.. ‘.,...~;-
.;..,‘. ,,:;t:.-, : :;; 
						

							System Parameters ProgrammingSystem Features 2 Programming2-31
Privacy Release Tone Option
Programming Steps
2Press the PRIVACY RELEASE TONE flexible button (FLASH 06, button #l). The
following message displays:
BARGEN;iLF;RN TONEO-l
sEnter a l-digit value on the dial pad to enable or disable the conference tone.
[ 0 ] = Disabled[I] = Enabled
4Press HOLD to save the entry. A confirmation tone is heard.
Display stations continue to receive the CONFERENCE display regardless
of the warning tone setting.
Privacy is ensured on all communications in the system. If desired, the user may elect to disable the
Automatic Privacy feature, thus allowing up to seven other stations to join existing CO Line conversations.Disabling of the privacy feature may be limited by federal, state, or local
law, so check the relevant laws in your area before disabling privacy.
Station Attempting toCO Line in Use by Another Station
Access CO LineIPrivacy Enabled 1  Privacy Disabled
I
I
Privacv EnabledII Private
I Private1 (no cut-through) 1 (no cut-through)1
Privacy DisabledPrivatePrivacy Release
(no cut-through) (cut-through allowed)
Table 2-5: CO Line Privacy Flag
STARPLUS Triad-S System Programming Manualissue I - December 1998 
						

							2-32System Parameters Programming
System Features 2 Programming
Distinctive CO Ringing
Programming Steps
iPress the CO RING TONE flexible button (FLASH 06, button #2). The following
message displays:
I
CO R&%T;~ESO-l
I
2Enter a l-digit value on the dial pad to enable/disable the tone ring signal.
[0] = Disabled
[I] = Enabled
3Press HOLD to save the entry. A confirmation tone is heard.
Description
The tone ring signal that notifies stations of an incoming call can be changed in administrative
programming to provide distinctive ringing on a per CO line basis. A distinctive ring tone can be
programmed for each CO line that rings each station. The system provides 
36 different ring patterns that
can be selected for CO lines in the system. By default, Distinctive CO ringing is enabled.
Verified Account Codes
Programming Steps
1Press the VERIFIED ACCT CODES flexible button (FLASH 06, button #3). The
following message displays:
VERIFIED ACCT CODESO-l
DISABLED
.
2Enter a l-digit value on the dial pad to enable/disable the use of verified account
codes.[0] = Disabled
[I] = Enabled
3Press HOLD to save the entry. A confirmation tone is heard.
~
issue I- December 1998STARPLUS Triad-S System Programming Manual 
						

							System Parameters Programming
System Features 2 Programming2-33
I
Description
The Verified Account Code/Traveling Class of Service (COS) feature provides tracking of specific calls by
-cc..- :x.:‘-.c--v1.-.z’:entering a verified, variable length (up to 12-digits) identifier. Each account code can be assigned a day and
night Class-of-Service for determining the dialing privileges allowed by that account code. This lets users
override a restricted station. If the dialed account code matches the Verified Account code table, an intercom
dial tone is returned, otherwise an error tone is returned. SMDR must be enabled for the account code to
print as part of the SMDR record. The Triad-S system allows up to 250 12-digit account codes programmed in
at Flash 31. By default, the Verified Account Codes feature is disabled.
Call Forward Display
Programming Steps
1Press the CALL FWD DISPLAY STATUS flexible button (FLASH 06, button #4). The
following message displays:
I
CALL FWD DISPLAYO-lENABLEDI
2Enter a l-digit value on the dial pad to enable/disable the call forward display option.
[0] = Disabled
[I] = Enabled
3Press HOLD to save the entry. A confirmation tone is heard.
Description
When call forwarding is invoked, the LCD display normally indicates the call forwarding mode at all times,
This feature is enabled/disabled in administrative programming on a system-wide basis. By default, the
status of the Call Forward display is enabled.
STARPLUS Triad-S System Programming Manualissue I- December 1998 
						

							2-34System Parameters Programming
System Features 2 Programming
External Day Ring
Programming Steps
iPress the EXT DAY RINGING flexible button (FLASH 06, button #5). The following
message displays:
I
EXTERNAL DAY RINGo-1
DISABLEDI
2Enter a l-digit value on the dial pad to enable/disable the use of external day ring
option.
[0] = Disabled
[l] = Enabled
3Press HOLD to save the entry. A confirmation tone is heard.
Description
The system can be programmed so CO lines marked for UDA provides ringing out of the external page ports
when the system is in the Day Mode. By default, External Day Ringing is disabled.
Overflow Station Forward
Programming StepsIPress the ACDIUCD OVERFLOW STA FWD flexible button (FLASH 06, button 
#6).The following message displays:
OVERFLOW STA FWDO-l
DISABLED
64
2Enter a l-digit value on the dial pad to enable/disable the use of this feature.
[0] = Disabled
[I] = Enabled
3Press HOLD to save the entry. A confirmation tone is heard.
Description
This feature allows ACD/UCD calls reaching the ACD/LJCD Overflow Station to call forward to another station.
This enhancement is allowed or denied on a system-wide basis. Once enabled in programming, anIssue I- December 1998
STARPLUS Triad-S System Programming Manual 
						

							System Parameters Programming
System Features 2 Programming2-35
ACD/UCD Overflow station can Busy/No-Answer forward to Voice Mail Groups, ACD/UCD Groups, Hunt
Groups and stations. If the 
ACD/LJCD Overflow station is busy or does not answer before the no-answer call
timer expires, the 
ACD/UCD call forwards to the destination, By default, this feature is disabled,
Direct Transfer Mode
Programming Steps
1Press the DIRECT TRANSFER flexible button (FLASH 06. button #7). The following
message displays:
I
DIRECT XFERO-lENABLEDI
2Enter a l-digit value on the dial pad to enable/disable this feature.
[0] = Disabled
[I] = Enabled
3Press HOLD to save the entry. A confirmation tone is heard.
Description
When enabled, supervised transfers (screened transfers) to stations in the handset mode connect calls
directly to the handset. The station user must have a direct appearance of that CO line or a Loop button. This
feature is programmed on a system-wide basis. By default, the Direct Transfer Mode is enabled.
Station ID Lock
Programming Steps
1Press the STATION ID LOCK flexible button (FLASH 06, button #8). The
message displays:following
.
STATION LOCKO-lDISABLED
2Enter a l-digit value on the dial pad to enable/disable the use of this feature.
[0] = Disabled
[I] = Enabled
3Press HOLD to save the entry. A confirmation tone is heard.
STARPLUS Triad-S System Programming Manual
Issue I- December 1998 
						

							 I:..2-36
System Parameters Programming
System Features 2 Programming
Description
This feature enables the installer/programmer to lock the station ID of all extensions on the system. It also
prevents the loss of station programming that results when a different station type is plugged into a port
already designated as another station type. This feature is programmed on a system-wide basis. By default,
the Station ID Lock feature is disabled.
The proper procedure(s) for changing the Station ID with the Station ID Lock feature enabled:
1Enter programming mode and disable the Station ID Lock feature.
2Plug the new device type into the jack. The set is automatically identified.
3Enter programming mode and disable the Station ID Lock feature.
4Enter programming and perform Station ID programming. (Flash 50, Page B, button #I).The set is automatically identified.
LCR Call Progress
Programming Steps
1Press the LCR CALL PROGRESS flexible button (FLASH 06, button #Q). The
following message displays:
LCR ;tUP;OGRESSO-l
2Enter a l-digit value on the dial pad to enable/disable the use of this feature.
[0] = Disabled
[I] = Enabled
3Press HOLD to save the entry. A confirmation tone is heard.
Description
This feature enables the installer to select, on a system-wide basis, whether users hear call progress
indications. By default, the LCR Call Progress feature is enabled.If this feature is disabled, a confirmation tone is given after the last digit is
dialed. The user does not hear the line being seized or the outpulsing of
digits to the Central Office.
Issue I- December 1998
STARPLUS Triad-S System Programming Manual 
						

							System Parameters Programming
System Features 2 Programming2-37
One-Touch Recording Warn Tone
Programming StepsPress the ONE-TOUCH RCD WARNING TONE flexible button (FLASH 06, button #IO).
The following message displays:
.
RECORDING WARN TONEO-lENABLED
\
2Enter a l-digit value on the dial pad to enable/disable the use of this feature.
[0] = Disabled
[I] = Enabled
3Press HOLD to save the entry. A confirmation tone is heard.
Description
This feature lets the installer enable/disable the One-Touch Recording Warning Tone on a system-wide basis.
By default, the Recording Warning Tone is enabled.Use of this feature when the One-Touch Recording Warn 
Toneis disabled
may be interpreted as a violation of federal, state, or local laws, and an
invasion of privacy. Check applicable laws in your area before recording
calls using this feature.
Ringback on Transfer
Programming Steps
1Press the RINGBACK ON TRANSFER flexible button (FLASH 06, button #ll). The
following message displays:
I
RINGBACK ON XFERO-lDISABLEDI
2Enter a l-digit value on the dial pad to enable/disable the use of this feature.
[0] = Disabled (Music)
[I] = Enabled (Ringback Tone)
3Press HOLD to save the entry. A confirmation tone is heard.
STARPLLJS Triad-S System Programming Manual
Issue 1 - December 1998 
						

							: --..-..2-38
System Parameters Programming
Programmable Flash Rates
Description
This feature provides on a system-wide basis music on hold or ringback tone to the CO caller when CO calls
are transferred. Callers currently hear music. By default, the 
Ringback on Transfer feature is disabled.
Programmable Flash Rates
Programming Steps
If the system is in the programming mode, continue using the program codes. If starting to program here,
enter the programming mode.
1Press FLASH and dial [07]. The following message displays:
.
SYSTEM FLASH RATES
ENTER BUTTON NUMBER
Description
This section describes the procedures and steps necessary to program the Flash Rates in the Flash Rates
programming area. The buttons on the digital terminal are illustrated on the following page:
Issue 1- December 7998STARPLUS Triad-S System Programming Manual