honda cr v 19997 2000 User Manual
Have a look at the manual honda cr v 19997 2000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 328 Honda manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Fuel Injectors
R6placomoni
1. Relieve the fuel pressure (see page 11-178).
2. Remove the resonato. chamber (99 - 00 models).
O.RINGBeplace.
Disconnect the connectors from the fuel injectors, and disconnect the IAT sensor 2P connector (97 - 98 models) and
EVAP purge control solenoid valve 2P conn€ctor (97 - 98 models),
Disconnect the PCV valve and the vacuum hose from the fuel pressure regulator.
Place a shop towel over the fuel return hose, then disconnect it from the fuel pressure regulator.
Remove the retainer nuts on the fuel rail.
Disconnect the fuel rail.
7, Remove the fuel injectors from the intake manifold.
97 - 98 model3:
EVAP PURGE CONTROLSOLENOID VALVE 2P CONNECTORIAT SENSOR
FUEL PULSATION2P CONNECTOR
12 N.m{1.2 kgtm,8.7 tbtft)
FUELPRESSUREREGULATOR
O.RING
FUELPRESSUREREGULATOR
CUSHION
O.RINGReplace.
CUSHIONRINGReplace.
SEALRINGReplace.
Replace.
SEALRINGReplace.
S
11-179
www.emanualpro.com
Fuel Supply System
Fuel Injectors {contdl
8. Slide new cushion rings onto the fuel injectors.
9, Coat newO-ringswith clean engine oil,and putthem onthefuel iniectors.
10. lnsert the fuel injectors into the fuel rail first.
11. Coatnewseal ringswithclean engineoil,and press them into the intake manifold
12. To prevent damage to the O-rings, install the fuel injectors in the fuel rail first, then install them in the intake mani-
fold.
FUEL RAIL
The ill!stration shows97 -98 models,99 - 00 modelsare similar.
13. lnstall and tighten the retainer nuts.
14. Connect the vacuum hoses and fuel return hose to the fuel pressure regulator.
15. Connect the PCV valve.
16. Connect the connectors to the fuel injectors, the IAT sensor (97 - 98 models), and the EVAP purge control solenoid
valve {97 - 98 models).
Coat a new O-ring with clean engine oil, and install the resonator chamber (99 - 00 models).
Turn the ignition switch ON (ll), but do not operate the starter. After the fuel pump runs for approximately two seconds,
the fuef pressure in the fuel line rises. Repeat this two or three times, then check whether there is any fuel leakage.
11.
18.
1 1-180
www.emanualpro.com
Fuel Pressure Regulator Tesiing 1. Attach the special tool and the 12 mm fuel pressure adapter bolt to the fuel filter (see page 1l-178) 2. Start the engine. Prasgure should be:97 - 98 models; 260 - 310 kPa (2.7 - 3.2 kgl/cm,38 -,16 psi)9!t - 00 models: 27O - 32o kPa l2-8 - 3.3 kgf/cm, 40 - /l7 psil (with the lugl pressure rsgulator vacuum hose dis- connested and pinched) FUELPRESSUREGAUGE07406 - 0040001 FUEL PRESSURENEGULATOR The illustration shows97 - 98 models,99 -00 modelsare similar. Reconnect the vacuum hose to the fuel pressure regulalor. Check that the fuel pressure rises when the vacuum hose from the fuel pressure regulator is disconnect- ed agarn. lf the fuel pressure did not rise, replace the fuel pressure regulator. 4. CLAMP Replacement 1. Place a shop towel under the fuel pressure regula- tor, then relieve fuel pressure (see page 11-1781. 2. Disconnect the vacuum hose and fuel return hose. 3. Remove the two 6 mm retainer bolts and the fuel pressure reguralor. 12 N.m(1.2 kgf.m,8.7 tbf.ft) The illustration shows97 - 98 models, 99 00 models are similar. Apply clean engine oil to a new O-ring. and carefully install it into its proper position. Install the fuel pressure regulator in the reverse order of removal, Replace. 1 1-181 www.emanualpro.com
Fuel Supply System Fuel Filter Replacamont . Do not smoke whilo working on tuol syslom,Keep open flame away from your work area.. While rsplscing ths fuolfihor. bo careful to ko€p a safedistanca betweon baftsry tarminals and any tools, The fuel filter should be replaced whenever the fuel Dres-sure drops below the specified value* with the fuel pres- sure regulator vacuum hose disconnected and pinchedl after making sure that the fuel pump and the fuel pres- sure regulator are OK. i: 97 - 98 modelsi 260 - 310 kPa 12.7 - 3.2 kgllcm2,3g - 46 psil99 - 00 mod6fs: 270 - 320 kP8 12.8 - 3.2 kgilcm2, 40 - il7psi) 1, Place a shop towel under and around the fuel filter. 2. Relieve fuel pressure (see page l1-l7B). 3. Remove the engine wire harness bracket and power steering feed hose clamp. 4. Remove the banjo bolt and the fuel feed pipe whilesupporting the fuel filter with another wrench. assnown. Remove the fuelfilter clamp and fuel filter, Install the new fuel filter in the reverse orde. ofremoval, and note these items: . When assembling, use new washers as shown.. Clean the flared joint of high pressure nosesthoroughly before reconnecting them. 11-182 12 mmSEAUNGBOLT33 hl.m l3.a kgt m,25 lbt frl 9.8 N.|n11.0 kgfm,t.2 tbt.ftl www.emanualpro.com
Fuel Pump
Testing
lf you suspect a problem with the fuel pump, check that
the fuel pump actually runs; when it is oN (ll), you will
hear some noise if you hold your ear to the fuel fill port
with the fuel fill cap removed. The fuel pump should run
for two seconds when ignition switch is first turned ON (ll).
lf the fuel pump does not make noise, check it as follows:
1. Fold the left rear seat cushion forward, and remove
the base frame cover (see section 20).
2, Remove the access panel from the floor.
3. Make sure the ignition switch is OFF, then discon-
nect the fuel pumP 5P connector.
4. Connect the PGM-FI main relay 7P connector termr-
nal No. 4 and No, 5 with a jumper wire.
PGM.FI MAINRELAY 7P CONNECTOR (Cit:}2l
ITtlJilt f -r-r ll.l5l517l,frTt-,at\FUEL pUMp Lr- . tcl tyEL/cRNl
rYEL/cRNl IIJUMPER Wir€ side of
WIRE female terminals
5. Check that battery voltage is available between the
fuel pump 5P connector terminal No. 4 and body
ground when the ignition switch is turned ON (ll).
FUEL PUMP 5P CONNECTOR {C562}
12
3a5
lf battery voltage is available, check the fuel
pump ground. lf the ground is OK, replace the
fuel oumo.
lf there is no voltage, check the wire harness (see
page 11-188).
FUEL PUMP(YEL/GRNI
wire side offemale terminals
Raplac6mont
1. Fold the left rear seat cushion forward, and remove
the base frame cover (see section 20).
2. Remove the access panel from the floor.
3, Relieve the fuel pressure (see page 11-178).
4. Disconnect the fuel lines.
5. Disconnect the 5P connector from the fuel pump.
6. Remove the fuel pump mounting nuts.
7. Remove the fuel pump from the fuel tank.
Install the fuel pump in the reverse order of
removal.
8.
11-183
www.emanualpro.com
Fuel Supply System
Fuel Gauge
Tssting
NOTE: Refer to section 23 for the fuel gauge system cir-cuit diagram.
1. Check the No. 25 METER (7.5 A) fuse in the under-dash fuse/relay box before testing.
2. Fold the left rear seat cushion forward, and remove
the base frame cover {see section 20).
3. Remove the access panel from the floor.
4. Disconnect the 5P connector from the fuel pump.
5. Measure voltage between the 5P connector termi-nals No.2 and No. 5 with the ignition switch ON ( ).There should be between 5 and 8 V.
FUEL PUMP5P CONNECTOR
tc56al
a
a
Wire side of female t€rminals
lf the voltage is as specified, go to step 6.lf the voltage is not as specified, check for:- an open in the YEUBLK or BLK wrre.- poor ground (c552).
11-184
7.
Turn the ignition switch OFF.
Attach a jumper wire between the No. 2 and No. 5terminals, then turn the ignition switch ON fll).
Check that the pointer of the fuel gauge starts mov-ing toward the F mark. Turn the ignition switchOFF before the pointer reaches F on the gauge
dial. Failure to do so may damage the luel gauge.
NOTE: The fuel gauge is a bobbin (cross-coil) type,hence the fuel level is continuously indicated evenwhen the ignition switch is OFF, and the pointer
moves more slowly than that of a bimetal type.
. lf the pointer of the fuel gauge does not move atall. replace the gauge.
. lf the gauge is OK, inspect the fuel gauge send-ing unit.
www.emanualpro.com
Fuel Gauge Sending Unit Tgsting @ Do not smoke while working on tho fuel systom. Keop open flamo 8waY from your work araa. 1. Fold the left rear seat cushion forward, and remove the base frame cover (see section 20). 2. Remove the access panel. 3. With the ignition switch OFF. disconnect the 5P con- nector from the fuel pump. 4. Relieve fuel pressure (see page 11-178). 5. Disconnect the fuel lines. 6. Remove the fuel pump, 7. Measure the resistance between the No. 2 and No. 5 terminals at E (EMPTY), 1/2 (HALF FULL) and F (FULL) by moving the float. lf you do not get the above readings, replace the fuel pump. 11-185 www.emanualpro.com
Fuel Supply System
Low Fuel Indicator System
Indicator Light Testing
NOTE: Refer to section 23forthe lowfuel lndicator circuit
clragram.
1. Check the No. 25 METER (7.5 A) fuse in the under-
dash fuse/relay box before testing.
2. Park the vehicle on level ground.
@ Do not smoke while working on the
fuel system. Keep open flame away trom the work
aroa. Drain fuel only into an approved container.
Drain the fuel into an aoDroved container. Then
install the drain bolt with a new washer.
Add less than 8 f (2.1 U.S. Gal. 1.8 lmp. Gal) of fuel,
and turn the ignition switch ON {ll). The low fuel indi-
cator light should come on within four minutes.
INDICATON LIGHT
. lf the light comes on within four minutes, go tostep 8.
. lf the light does not come on within four min-
utes. go to step 5.
Remove the seat cushion (see section 20).
Remove the fuel tank access panel from the floor,
and disconnect the 5P connector from the fuel pump,
Connect the No. 1 and No. 2 terminals with a jumper
wire.
. lf the lightcomeson, checkthe sending unit.. lf the light does not come on, check for:- an open in the GRN/yEL wire between thefuel unit and fuel gauge assembly.- blown bulb.- poor ground (G552).
FUEI- PUMP 5P CONNECTOR (C562)
JUMPER WIRE
IGRN/YEL}
7.
1 1-1 86
Wire sid€ ol tem€le terminals
8. Add 4 / of fuel (1.1 U.S. Gal, 0.9 lmp. Gal). The light
should go off within four minutes.
. lJ the light does not go off, check for:- a short in the GRNA/EL wire between the fuel
gauge sending unit and fuel gauge assembly.- faulty gauge assembly.
. lf the light goes off, the low fuel indicator light is
oK.
www.emanualpro.com
PGM-FI Main Relay Description The PGM-Fl main relav actuallv contains two individual relays. This relay is located at the passenger side of the cowl. One relay is energized whenever the ignition is on which supplies the battery voltage to the ECM/PCM, power to the fuel injectors, and power for the second relay. The second relay is energized for two seconds when the ignition is switched on, and when the engine is running, to supply power to the fuel pump PGM.FIMAIN RELAY Belay Testing NOTE: lf the engine starts and continues to run, the PGM-FI main relay is OK. 1. Remove the glovebox and the passengers dash- board lower cover (see section 20). 2. Remove the PGM-FI main relay 3. Aftach the battery positive terminal to the No. 2 ter- minal and the battery negative terminal to the No. 1 terminal of the PGM-Fl main relay. Then check for continuity between the No. 5 terminal and No. 4 ter- minal of the PGM-FI main relay . lfthere is continuity, go on to step 3. . lf there is nocontinuity, replacethe PGM-Fl main relav and retest. No.2 To lGN. 1 To GROUND To ST. SWITCH To ECM/PCMCONNECTORTERMINAL A16(FLR) To BAT O To FUEL PUMPTo ECM/PCMCONNECTORTERMINAL(411 and A24,Bl .nd Bgal(IGP) To FUEL PUMP 98 - 00 models Attach the batterv Dositive terminal to the No. 5 ter- minal and the battery negative terminal to the No. 3 termjnal of the PGM-Fl main relay. Then check that there is continuity between the No. 7 terminal and No. 6 terminal of the PGM-FI main relay. . lf there is continuity, go on to step 4. . lf there is nocontinuity, replacethe PGM-Fl main relay and retest. Attach the batterv oositive terminal to the No.6 ter- minal and the battery negative terminal to the No. 1 terminal of the PGM-Fl main relay. Then check that there is continuitv between the No. 5 terminal and No. 4 terminal of the PGM-Fl main relay. . lf there is continuity, the PGM-Fl main relay is OK. . lf there is nocontinuity, replacethe PGM-FI main 5. (contd) 11-147 No.5 No.5 relay and retest. www.emanualpro.com
Fuel Supply System
PGM-FI Main Relay (contdl
Troubleshooting
lc(}21PGM.FI MAIN RELAY 7P CONNECTOR
GND
trTr]--Flq
FI,TilI A
Y
Wire side ot female terminals
- Engine will not start.- InsDection ol PGM-FI mainrelay and relay harness,
Check fo. an open in the wireIGND linol:1. Turn the ignition switch OFF.2. Disconnect the PGM Fl mainrelay 7P connector.3. Check for continuity betweenthe PGMFI main relay 7P con-nector terminal No. 3 and bodyground.
Repair opcn in th€ wire betweenthe PGM-FI main relav and G101.
Check tor an open or short in thewiro (BAT line):Measure voltage between thePGMFI main relay 7P connectorterminal No. 7 and body ground.- Repai. open or short in lhewir6 belween the PGM-FImain relay and the Fl E/M (15Al fu3e.- Replace th6 FIE/M (15 Altus6in th€ under-hood fuse/.6lay
ls there baftery voltage?
Check lor an open or short in thewire (lGl line):L Turn the ignition switch ON (ll).2. Measure the voltage betweenthe PGM-FI main relay 7P connectorterminal No. 5 and bodyground.- Repair open or shorl in thewire between the FGM-FI mainrelay and the No. 13 FUELPUMP 115 A) tuse.- Replaco the No. 13 RJEL PUMP115 A) luse in the und6.-d$hfuso/ relav box.Check for an open or short in thewire {STS line):1. Turn the ignition switch to theSTART (lll) position.NOTE:. M/T: Clutch pedal must bedepressed.. A/T: Transmission in E orElposition.2. Measure the voltage betweenthe PGM-Fl main retay 7Pconnector terminal No. 2 andbody ground.- Repair open or short in thewire betwe€n the PIGM-FI m.inrclay and th€ No. 31 STARTERSlGllAL 17.5 A) tuse.- Repl.ce the No. 31 STARTERSIGNAL 17.5 Al tuse in theunder-dash tuse/relay box.(97 model: To page 11-189)(98 00models:To page 1l 190)
1 1-188
www.emanualpro.com