Home
>
Lucent Technologies
>
Communications System
>
Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Administrators Guide
Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Administrators Guide
Have a look at the manual Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Administrators Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 413 Lucent Technologies manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1 April 2000 Screen reference 867 Route Pattern 17 NPA This entry is not required for AAR. Prefix Mark This entry is not required for AAR. For ARS, enter a number from 0 to 4 or blank. Prefix Marks set the requirements for sending a prefix digit 1, indicating a long-distance call. Prefix Marks apply to 7- or 10-digit Direct Distance Dialing (DDD) public network calls. A prefix digit 1 is sent only when call type is foreign number plan area (FNPA) or home numbering plan area (HNPA) in the ARS Digit Analysis table. For a WATS trunk, the Prefix Mark is the same as the local CO trunk. Valid entries Usage 3-digit number Enter the 3-digit Numbering Plan Area (NPA) (or area code) for the terminating endpoint of the trunk group. Call your local telephone company to verify this number if you need help. For WATS trunks, the terminating NPA is the same as the home NPA unless the Local Exchange Carrier requires 10 digits for local NPA calls. blank For AAR calls and for tie trunks Valid entries Usage 0 nSuppress a user-dialed prefix digit 1 for 10-digit FNPA calls. nLeave a user-dialed prefix digit 1 for 7-digit HNPA calls. nLeave a prefix digit 1 on 10-digit calls that are not FNPA or HNPA calls. Do not use Prefix Mark 0 in those areas where all long-distance calls must be dialed as 1+10 digits. Check with your local network provider. 1nSend a 1 on 10-digit calls, but not on 7-digit calls. Use Prefix Mark 1 for HNPA calls that require a 1 to indicate long-distance calls. 2nSend a 1 on all 10-digit and 7-digit long-distance calls. Prefix Mark 2 refers to a Toll Table to define long distance codes.
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1 April 2000 Screen reference 868 Route Pattern 17 Hop Lmt Enter the number of hops for each preference. A hop is when a call tandems through a switch to another destination. Limiting the number of hops prevents circular hunting, which ties up trunk facilities without ever completing the call. DEFINITY ECS blocks a hop equal to or greater than the number you enter. Toll List This entry is not required for AAR. 3nSend a 1 on all long-distance calls and keep or insert the NPA (area code) so that all long distance calls are 10-digit calls. The NPA is inserted when a user dials a Prefix digit 1 plus 7-digits. Prefix Mark 3 refers to a Toll Table to define long distance codes. 4nAlways suppress a user-dialed Prefix digit 1. Use Prefix Mark 4, for example, when ISDN calls route to a switch that rejects calls with a prefix digit 1. blank For tie trunks, leave this field blank. Valid entries Usage blank Indicates that there is no limit to the number of hops for this preference. 1 to 9To limit the number of hops if using the tandem hop feature. 1 to 32If using the transit feature. Valid entries Usage 1 to 32For ARS, enter the number of the ARS Toll Table associated with the terminating NPA of the trunk group. You must complete this field if Prefix Mark is 2 or 3. Valid entries Usage
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1 April 2000 Screen reference 869 Route Pattern 17 No. Del. Digits Use this field to modify the dialed number so an AAR or ARS call routes over different trunk groups that terminate in switches with different dial plans Inserted Digits Enter the digits you want inserted for routing. The switch can send up to 52 digits. This includes up to 36 digits you may enter here plus up to 18-digits originally dialed. Special symbols count as two digits each. Valid entries Usage 0 to 28Enter the total number of digits you want the system to delete before it sends the number out on the trunk. Use for calls that route: nto or through a remote switch nover tie trunks to a private network switch nover Central Office (CO) trunks to the serving CO Valid entries Usage (0 to 9) 0 to 36 digitsEnter the digits you want inserted for routing. * When * is in the route pattern and the outgoing trunk is signaling type “mf”, the MFC tone for the “end-of-digits” is sent out to the CO in place of the *. # When # is in the route pattern and the outgoing trunk is signaling type “mf”, the MFC tone for the “end-of-digits” is sent out to the CO in place of the #. ‘ ,’ Use 2 places. Creates a 1.5 second pause between digits being sent. Do not use as the first character in the string unless absolutely necessary. Misuse can result in some calls, such as Abbreviated Dialing or Last Number Dialed, not completing. + Wait for dial tone up to the Off Premises Tone Detection Timer and then send digits or intercept tone based on Out Pulse Without Tone y/n on the Feature-Related System Parameters screen. % Start End-to-End Signaling. ! Wait for dial tone without timeout and then send DTMF digits. & Wait for ANI (used for Russian pulse trunks)
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1 April 2000 Screen reference 870 Route Pattern 17 IXC Inter-Exchange Carrier (IXC) identifies the carrier, such as AT&T, used for calls that route via an IXC, and for Call Detail Recording (CDR). This field appears when the ISDN-PRI or ISDN-BRI Trunks field is y on the System-Parameters Customer-Options screen. BCC Value Bearer Capability Class (BCC) identifies the type of call appropriate for this trunk group, such as voice calls and different types of data calls. This field appears when the ISDN-PRI or ISDN-BRI Trunks field is y on the System-Parameters Customer-Options screen. The following table explains BCC values: Valid entries Usage Valid carrier codeIdentifies the carrier for IXC calls userFor presubscribed carrier. Used when an IXC is not specified. noneThis field must be none for non-ISDN trunk groups and for Bellcore NI-2 Operator Service Access. If you need to send an IXC code for a non-ISDN trunk group, enter the IXC code in the Inserted Digits field. Valid entries Usage y / nEnter y in appropriate BCC column (0, 1, 2, 3, 4, or W) if the BCC is valid for the associated route pattern. A trunk group preference may have more than one BCC. BCC Value Description 0 Voice-Grade Data and Voice 1 56-kbps Data (Mode 1) 2 64-kbps Data (Mode 2) 3 64-kbps Data (Mode 3) 4 64-kbps Data (Mode 0) W 128 to 1984-kbps Data (Wideband)
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1 April 2000 Screen reference 871 Route Pattern 17 TSC Set TSC to y for feature transparency on DCS+ calls and to use QSIG Call Completion. CA-TSC Request Use CA-TSC on ISDN B-channel connections. ITC (Information Transfer Capability) Use Information Transfer Capability (ITC) to identify the type of data transmission or traffic that this routing preference can carry. The ITC applies only to data calls (BCC 1 through 4). This field must be unre or both if the BCC is y and the BCC value is W Valid entries Usage y/n Enter y to allow Call-Associated TSCs, and to allow incoming Non-Call-Associated TSC requests to be tandemed out for each preference. Valid entries Usage as-needed The CA-TSC is set up only when needed. This causes a slight delay. This entry is recommended for most situations. at-setupThe CA-TSC is automatically set up for every B-channel call whether or not it is needed. noneNo CA-TSC is set up. Permits tandeming of NCA-TSC setup requests0. Valid entries Usage both Calls from restricted and unrestricted endpoints can access the route pattern. rest(ricted) Calls from restricted endpoints can access the route pattern. unre(stricted) Calls from unrestricted endpoints can access the route pattern.
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1 April 2000 Screen reference 872 Route Pattern 17 BCIE (Bearer Capability Information Element) Use BCIE to determine how to create the ITC codepoint in the setup message. This field applies to ISDN trunks and appears if ITC is both. Service/Feature Enter up to 15 characters to identify the Service/Feature carried by the information element (IE) in a call in this route pattern. This field is required by Call-by-Call Service Selection. Service/Feature appears when ISDN-PRI or ISDN-BRI Trunks is y on the System-Parameters Customer-Options screen. Band Enter a number that represents the OUTWATS band number (US only). WATS is a voice-grade service that provides both voice and low-speed data transmission calls to defined areas (bands) for a flat rate charge.0 This field appears when the Services/Features field is outwats-bnd and when ISDN-PRI or ISDN-BRI Trunks field is y on the System-Parameters Customer-Options screen. Band is required by Call-by-Call Service Selection. No. Dgts Subaddress Allows a caller to reach a number where switch digit processing deletes the dialed number and inserts the listed directory number (LDN). The LDN then is sent to the destination address and the dialed extension is sent in the calling party Valid entries Usage ept (endpoint) unr (unrestricted) Valid entries accunet multiquest sdn i800 operator sub-operator inwats oper-lds (operator and lds) sub-op-lds (sub-operator and lds) lds oper-meg (operator and megacon)sub-op-meg (sub-operator and megacom) mega800 oper-sdn (operator and sdn)sub-op-sdn (sub-operator and sdn) megacom outwats-bnd wats-max-bnd
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1 April 2000 Screen reference 873 Route Pattern 17 subaddress information element (IE). At the receiving end, the call terminates to the user indicated by the subaddress number instead of the attendant. Administrable when, on the System-Parameters Customer-Option screen, the ISDN Feature Plus field is y. Numbering Format This field applies only to ISDN trunk groups. Enter a value from table below. This field specifies the format of the routing number used for the trunk group for this preference. This field appears when the ISDN-PRI or ISDN-BRI Trunks field is y on the System-Parameters Customer-Options screen. NOTE: To access Bellcore NI-2 Operator Service Access, the Inserted Digits field must be unk-unk. Valid entries Usage 1 - 5 blankEnter the number of dialed digits to send in the calling party subaddress IE. Valid entries Numbering Plan Identifier Type of Numbering blank E.164(1) 1-MAX natl-pub E.164(1) national(2) intl-pub E.164(1) international(1) locl-pub E.164(1) local/subscriber(4) pub-unk E.164(1) unknown(0) lev0-pvt Private Numbering Plan - PNP(9) local(4) lev1-pvt Private Numbering Plan - PNP(9) Regional Level 1(2) lev2-pvt Private Numbering Plan - PNP(9) Regional Level 2(1) unk-unk unknown(0) unknown(0)
DEFINITY ECS Release 8.2
Administrator’s Guide 555-233-506 Issue 1
April 2000
Screen reference
874 Second Digit Table
17
LAR
Enter the routing-preference for Look Ahead Routing.
Second Digit Table
You must complete the Second Digit Table each time you enter misc in the digit
length of 1 column on the Dial Plan Record screen. The second digit table is
named for the row where the
misc appears. In addition, a second digit table can
exist for every first digit value.
Screen 180. Second Digit Table
Digit
A display-only field that marks the value of the second digit.
Valid entries Usage
next
Go to the next routing preference and attempt the call again.
rehuRehunt within the current routing-preference for another trunk
to attempt the call again.
none Look Ahead Routing is not enabled for the preference.
change second-digit x Page 1 of 1
SECOND DIGIT TABLE FOR DIGIT _
SECOND DIGIT TABLE
Digit Identification Number of Digit Identification Number of
Digits Digits
0: __________ 0 5: __________ 0
1: __________ 0 6: __________ 0
2: __________ 0 7: __________ 0
3: __________ 0 8: __________ 0
4: __________ 0 9: __________ 0
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1 April 2000 Screen reference 875 Security-Related System Parameters 17 Identification Number of Digits This field tells the system how many digits to collect if the first and second digits match. Enter the length of the dialed number. Security-Related System Parameters You use this screen to determine when the switch reports a security violation. Many of the fields on this screen repeat for each type of security violation. We have explained them once here, but the usage is the same for all. Refer to ‘‘Security violations notification’’ on page 1479 for more information on security violations notification. Valid entries Usage attd Enter an abbreviation to identify the dialed number when a second digit is dialed. See the first digit table information, in ‘‘ Dial Plan Record’’ on page 593, for an explanation of these entries.extension tac fac ars aar Valid entries Usage 2 For attd 2 through 5For aar, ars, and extension 2 through 4For tac (2 and 3 with DCS) 2 through 4For fac
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1 April 2000 Screen reference 876 Security-Related System Parameters 17 Field descriptions for page 1 Screen 181. Security-Related System Parameters SVN Login (Remote Access, AutoStation Security Code, Violation Notification Enabled Originating Extension The originating extension initiates the referral call in the event of a security violation. It also sends the appropriate alerting message or display to the referral destination. Valid entries Usage y/n Set to y if you want the switch to notify you when a login violation occurs. If this field is y, the next 5 fields appear so you can establish the parameters for what is considered a security violation. Valid entries Usage An unassigned extensionIf you establish notification for more than one type of security violations, you must assign a different extension to each one. When the switch generations a referral call, this extension and the type of violation appear on the display at the referral destination. change system-parameters security Page 1 of 2 SECURITY-RELATED SYSTEM PARAMETERS SECURITY VIOLATION NOTIFICATION PARAMETERS SVN Login Violation Notification Enabled? y Originating Extension: _____ Referral Destination: _____ Login Threshold: 5_ Time Interval: 0:03 Announcement Extension: _____ SVN Remote Access Violation Notification Enabled? y Originating Extension: _____ Referral Destination: _____ Barrier Code Threshold: 10 Time Interval: 0:03 Announcement Extension: _____ SVN Authorization Code Violation Notification Enabled? y Originating Extension: _____ Referral Destination: _____ Authorization Code Threshold: 10 Time Interval: 0:03 Announcement Extension: _____