Panasonic Kx-Td816e, Kx-td1232e User Manual

							Station Programming2-37
2.2Station Programming
Prime Line (CO Line) Preference — Incoming (Assignment)
When you go off-hook,you answer a call on the line which is assigned as the prime line.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 2.
•The display shows the current status.
2.Dial 3.
3.Dial the CO line numberas follows.
- 01 through 08 :if you are connected to the KX-TD816
- 01 through 24 :if you are connected to the KX-TD1232
•The display shows:
(— CO line number xx is
selected)
4.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Pref.In :CO-xx
1
2
4
AUTO DIAL
STORE
3
CO line number
3
2 
						

							2-38Station Programming
2.2Station Programming
Preferred Line Assignment — Outgoing
Allows you to select the desired outgoing line preference to originate calls from the
following four line preferences:
1.) No Line Preference
2.) Idle Line Preference
3.) Prime Line (CO line) Preference
4.) Prime Line (INTERCOM) Preference (— default)
Follow the programming procedure for your selection.

When setting “Idle Line Preference,”“No Line Preference”or “Prime Line (CO Line)
Preference,”it is not possible to have access to any DPT features after going off-hook.  To
access these DPT features,press the INTERCOM button before or after going off-hook.
No Line Preference — Outgoing (Assignment)
When you go off-hook,you are not connected to any line.  You must make a choice.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 1.
•The display shows the current status.
2.Dial 1.
•The display shows:
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Pref.Out:No
2
3
AUTO DIAL
STORE
1
1
1 
						

							Station Programming2-39
2.2Station Programming
Idle Line Preference — Outgoing (Assignment)
When you go off-hook,you are connected to an idle line.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 1.
•The display shows the current status.
2.Dial 2.
•The display shows:
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Prime Line (CO Line) Preference — Outgoing (Assignment)
When you go off-hook,you are connected to the pre-assigned line.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 1.
•The display shows the current status.
2Dial 3.
3.Dial the CO line numberas follows.
- 01 through 08 :if you are connected to the KX-TD816
- 01 through 24 :if you are connected to the KX-TD1232
•The display shows:
(—xx:CO line number xx is
selected)
4.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
1
2
4
AUTO DIAL
STORE
3
CO line number
3
1
Pref.Out:CO-xx
Pref.Out:Idle
2
3
AUTO DIAL
STORE
2
1
1 
						

							Prime Line (INTERCOM) Preference — Outgoing (Assignment)
When you go off-hook,you are connected to the INTERCOM line.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 1.
•The display shows the current status.
2.Press the INTERCOMbutton.
•The display shows:
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
2-40Station Programming
2.2Station Programming
2
3
AUTO DIAL
STORE
1
1
INTERCOMPref.Out:ICM 
						

							Station Programming2-41
2.2Station Programming
Ringing Tone Selection for CO Buttons
Allows you to assign a ringer frequency to each CO button.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the CObutton which you wish to change the ringing
tone.
2.Press the same CObutton again.
•The display shows the current status.
3.Enter the tone type number(1 through 8).
•The display shows the selected tone type number and you
hear the selected tone until the STORE button is pressed.
(— x:tone type number) 
•If you want to change the tone type,enter another tone type
number in succession.
4.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Conditions
•Default is Ringing Tone Type 2.
Tone Type-x
1
2
4
AUTO DIAL
STORE
3
tone type number
CO
CO 
						

							2-42Station Programming
2.2Station Programming
Ringing Tone Selection for Intercom Calls
Allows you to assign a ringer frequency for intercom call.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the INTERCOMbutton which you wish to change the
ringing tone.
2.Press the same INTERCOMbutton again.
•The display shows the current status.
3.Enter the tone type number(1 through 8).
•The display shows the selected tone type number and you
hear the selected tone until the STORE button is pressed.
(— x:tone type number) 
•If you want to change the tone type,enter another tone type
number in succession.
4.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit the Station Programming mode:Press [PROGRAM] or lift the handset.
Condition
•The default is Ringing Tone Type 2.
Tone Type–x
1
2
4
AUTO DIAL
STORE
3
tone type number
INTERCOM
INTERCOM 
						

							Station Programming2-43
2.2Station Programming
Self-Extension Number Confirmation (Display DPT only)
Allows you to display your jack and extension number on the display.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9]. 
1.Dial 6.
•The display shows your jack and extension number.

2.Press the HOLD(END) button.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Station Programming Data Default Set
Allows you to return each of the following programmable items to their default settings.
a)Call Waiting Tone Type Assignment (default:Tone 1)
b)Full One-Touch Dialling Assignment (default:On)
c)Handset/Headset Selection (default:Handset)
d)Intercom Alerting Assignment (default:Ring-Calling)
e)Live Call Screening Mode Set (default:Hands-free)
f)Preferred Line Preference — Incoming (default:Ringing Line)
g)Preferred Line Preference — Outgoing (default:INTERCOM Line)
— Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial #.
•The display shows:
2.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
— To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
2 1
6
HOLD
2 1AUTO DIAL
STORE
Jack01EXT101
Clear Ready? 
						

							2-44Station Programming
2.2Station Programming
1
2
3
AUTO DIAL
STORE
desired number
PT-PGM ModeF5
F4
F3
F2
F1
F10
F9
F8
F7
F6
9-431-2111
CLRNEXT
Station Speed Dialling Number / Name Assignment 
(KX-T7235 / KX-T7431 / KX-T7433 / KX-T7436 only)
Allows you to assign frequently dialled numbers and names to each Function button on
your telephone.
For KX-T7235 and KX-T7436 users
To store a number
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press a Functionbutton (F1 through F10).
•The STORE indicator light turns off.
•The display shows the current status.

(—The outside call,431-2111,
is now programmed.)
2.Enter the desired number(up to sixteen digits).
•0 through 9,,#,RECALL or FLASH/RCL,PAUSE,
INTERCOM,( “[”or “]”:secret) and CONF (–:hyphen)
can be used.
•To store the telephone number of an outside party,the line
access code (9 or 81 through 88) must be the leading digit.
•To erase the entry,press the CLR (S2) button.
3.Press the STOREbutton.
•The STORE indicator lights.
•The display shows the initial programming mode.
—To exit the Station Programming mode:Press [PROGRAM] or lift the handset. 
						

							Station Programming2-45
2.2Station Programming
3
4
AUTO DIAL
STORE
name
2
S 1
S 2
S 3
NEXT
Mike
CLRNEXT
1
PT-PGM ModeF5
F4
F3
F2
F1
F10
F9
F8
F7
F6
To store a name
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press a Functionbutton (F1 through F10).
•The STORE indicator light turns off.
•The display shows the current status.
2.Press the NEXT (S3) button.
•The display shows the current status.

(— The name is now
programmed.)
3.Enter the name.
•Refer to the Combination Table on pages 2-48 and 2-49 on
how to enter each character.
4.Press the STOREbutton.
•The STORE indicator lights.
•The display shows the initial programming mode.
—To exit the Station Programming mode:Press [PROGRAM] or lift the handset. 
						

							2-46Station Programming
2.2Station Programming
For KX-T7431 and KX-T7433 users
To store a number
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press .
2.Enter the Station Speed Dial number(0 through 9).
•The STORE indicator light turns off.
•The display shows the current status.

(—The outside call,431-2111,
is now programmed.)
3.Enter the desired number(up to sixteen digits).
•0 through 9,,#,RECALL or FLASH/RCL,PAUSE,
INTERCOM,( “[”or “]”:secret) and CONF (–:hyphen)
can be used.
•To store the telephone number of an outside party,the line
access code (9 or 81 through 88) must be the leading digit.
•To erase the entry,press the CLR (S2) button or
TRANSFER button.
– CLR (S2) button:for KX-T7433 users
– TRANSFER button:for KX-T7431 users
4.Press the STOREbutton.
•The STORE indicator lights.
•The display shows the initial programming mode.
—To exit the Station Programming mode:Press [PROGRAM] or lift the handset.
1
4
AUTO DIAL
STORE
2
Station Speed Dial number
3
desired number
9-431-2111
CLRNEXT