Panasonic Kx-Td816e, Kx-td1232e User Manual

							Station Programming2-27
2.2Station Programming
Single-CO (S-CO) Button (Assignment)
Allows you to assign a Flexible (CO) button as a Single-CO button.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the Flexible(CO) button which you wish to assign as an
S-CO button.
2.Dial 0.
•The display shows:
3.Enter the CO line numberas follows.
- 01 through 16:if you are connected to the KX-TD816
- 01 through 54:if you are connected to the KX-TD1232
•The display shows:
(— xx:CO line number)
•To erase an incorrect entry,press the CLR (S2) button or
the TRANSFER (CLEAR) button.
(The TRANSFER button becomes the CLEAR button when using the
overlay.)
4.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Conditions
•You cannot assign the same CO line to more than one S-CO button on a proprietary
telephone.
•You can assign a CO line to a S-CO and a G-CO button.
CO—
CLR
CO—xx
CLR
1
2
4
AUTO DIAL
STORE
3
CO line number
0 
						

							2-28Station Programming
2.2Station Programming
Terminate Button (Assignment)
Allows you to assign a Flexible (CO,DSS,PF) button as the Terminate button.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the desired Flexible(CO,DSS,PF) button which you
wish to assign as the Terminate button.
2.Dial 9.
•The display shows:
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
1
2
3
AUTO DIAL
STORE
9
Terminate 
						

							Station Programming2-29
2.2Station Programming
†:Available when the Digital Super Hybrid System is connected to a Digital
Proprietary Telephone capable Panasonic Voice Processing System. (one
that supports digital proprietary telephone integration; e.g. KX-TVP100).
Two-Way Record Button (Assignment) †
Allows you to assign a Flexible (CO,DSS) button as a Two-Way Record button.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the desired Flexible(CO,DSS) button which you wish
to assign as a Two-Way Record button.
2.Dial 83.
•The display shows:
3.Enter the extension number of the Voice Mail.
•The display shows:
(—xxxx:VM extension
number)
•To erase an incorrect entry,press the CLR (S2) button or
the TRANSFER (CLEAR) button.
(The TRANSFER button becomes the CLEAR button when using the
overlay.)
4.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Conditions
•You cannotenter a non-existent extension or a floating number.*
•The voice mail extension number is acceptable,if the number is assigned in program
[127].
Programming References
•System Programming — Installation Manual
[127]Voice Mail Extension Number Assignment
*Floating Number (FN) is a virtual extension number for resources to make it appear to be an extension.
Refer to the Installation Manual.
1
2
4
AUTO DIAL
STORE
3
VM extension number
2 WAY-REC:
CLR83
2 WAY-REC:xxxx
CLR 
						

							2-30Station Programming
2.2Station Programming
†:Available when the Digital Super Hybrid System is connected to a Digital
Proprietary Telephone capable Panasonic Voice Processing System. (one
that supports digital proprietary telephone integration; e.g. KX-TVP100).
Two-Way Transfer Button (Assignment) †
Allows you to assign a Flexible (CO,DSS) button as a Two-Way Transfer button.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the desired Flexible(CO,DSS) button which you wish
to assign as the Two-Way Transfer button.
2.Dial 84.
•The display shows:
3.Enter the extension number of the Voice Mail.
•The display shows:
(—xxxx:VM extension
number)
•To erase an incorrect entry,press the CLR (S2) button or
the TRANSFER (CLEAR) button.
(The TRANSFER button becomes the CLEAR button when using the
overlay.)
4.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Conditions
•You cannotenter a non-existent extension or a floating number.*
•The voice mail extension number is acceptable,if the number is assigned in program
[127].
Programming References
•System Programming — Installation Manual
[127]Voice Mail Extension Number Assignment
*Floating Number (FN) is a virtual extension number for resources to make it appear to be an extension.
Refer to the Installation Manual.
1
2
4
AUTO DIAL
STORE
3
VM extension number
842 WAY-TRANS:
CLR
2 WAY-TRANS:xxxx
CLR 
						

							Station Programming2-31
2.2Station Programming
Voice Mail (VM) Transfer Button (Assignment)
Allows you to assign a Flexible (CO,DSS,PF) button as the VM Transfer button.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the desired Flexible(CO,DSS,PF) button which you
wish to assign as the VM Transfer button.
2.Dial 82.
•The display shows:
3.Dial the extension number of the Voice Mail.
•The display shows:
(—xxxx:VM extension
number)
•To erase an incorrect entry,press the CLR (S2) button or
the TRANSFER (CLEAR) button.
(The TRANSFER button becomes the CLEAR button when using the
overlay.)
4.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Conditions
•You cannotenter a non-existent extension or a floating number.*
•Through System Programming,“VM command DTMF Set”and “Station Hunting
Type”must be programmed to match the operation of your Voice Processing System.
Programming References
•System Programming — Installation Manual
[106]Station Hunting Type
[114]VM Command DTMF Set
*Floating Number (FN) is a virtual extension number for resources to make it appear to be an extension.
Refer to the Installation Manual.
1
2
4
AUTO DIAL
STORE
3
VM extension number
82VTR-
CLR
VTR-xxxx
CLR 
						

							2-32Station Programming
2.2Station Programming
Full One-Touch Dialling Assignment
Allows you to enable or disable the “Full One-Touch Dialling”function. “Handsfree
Operation”mode is activated by pressing an One-Touch Dialling button,a DSS button,a
REDIAL button or a SAVE button.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 3.
•The STORE indicator light turns off.
•The display shows the current status.

(— When disabled)
2.Dial 1or 2.
- 1 :for selecting the off mode
- 2 :for selecting the on mode
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Conditions
•Default is “On”mode.
Handset / Headset Selection
Allows you to select the handset mode or headset mode.
— Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 9.
•The display shows the current status.
2.Dial 1or 2.
- 1 :for selecting Handset mode
- 2 :for selecting Headset mode
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
— To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Conditions
•Default is “Handset”mode.
1
2
3
AUTO DIAL
STORE
21
3
orHands-free:Off
1
2
3
AUTO DIAL
STORE
21or
9 
						

							Station Programming2-33
2.2Station Programming
Intercom Alerting Assignment
Allows you to select the alerting mode (tone / voice) when receiving an intercom
(extension) call.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 4.
•The display shows the current status.
(—When Ring-Calling (Tone
Call) mode is selected)
(—When Voice-Calling mode
is selected)
2.Dial 1or 2.
- 1 :for selecting Ring-Calling (Tone Call) mode
- 2 :for selecting Voice-Calling mode
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Conditions
•Default is “Ring-Calling (Tone Call)”mode.
Tone Call
Voice Call
1
2
3
AUTO DIAL
STORE
21or
4 
						

							2-34Station Programming
2.2Station Programming
†:Available when the Digital Super Hybrid System is connected to a Digital
Proprietary Telephone capable Panasonic Voice Processing System. (one
that supports digital proprietary telephone integration; e.g. KX-TVP100).
Live Call Screening Mode Set †
Assign whether an alert tone is sent (Private mode) or the recording message is monitored
through the built-in speaker (Hands-free mode),while incoming callers are leaving a
message.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 1.
•The display shows the current status.
(—When Hands-free mode is
selected)
(—When Private mode is
selected)
2.Dial 1or 2.
- 1 :for selecting Hands-free mode
- 2 :for selecting Private mode
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Conditions
• Default is “Hands-free”mode.
1
2
3
AUTO DIAL
STORE
21or
1
Hands-free
Private 
						

							Station Programming2-35
2.2Station Programming
Phantom Extension Bell On / Off Set
You can select whether or not the bell will ring when a call is received at a phantom
extension.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the Phantom Extensionbutton.
2.Press the same Phantom Extensionbutton again.
3.Dial 1or 2.
- 1 :Ring off
- 2 :Ring on
4.Press the STOREbutton.
•The STORE indicator light turns on.
—To exit the Station Programming mode:Press [PROGRAM] or lift the handset.
1
2
3
12or
4AUTO DIAL
STORE 
						

							2-36Station Programming
2.2Station Programming
Preferred Line Assignment — Incoming
Allows you to select the method used to answer incoming calls from the following three
line preferences:
1.) No Line Preference
2.) Ringing Line Preference (— default)
3.) Prime Line (CO Line) Preference
Follow the appropriate programming procedure for your selection.
No Line Preference — Incoming (Assignment)
No line is selected when you go off-hook.  You must select a line to answer.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 2.
•The display shows the current status.
2.Dial 1.
•The display shows:
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Ringing Line Preference — Incoming (Assignment)
When you go off-hook,you answer any call ringing at your telephone.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 2.
•The display shows the current status.
2.Dial 2.
•The display shows:
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Pref.In :No
Pref.In :Ring
2
3
AUTO DIAL
STORE
1
2
1
2
3
AUTO DIAL
STORE
2
1
2