Panasonic Kx-Td816e, Kx-td1232e User Manual

							7-84SLT and ISDN Telephone Features
T7.2SLT and ISDN Telephone Features
Toll Restriction Override
There are two types of toll restriction override:
•Toll Restriction Override by Account Code Entry
•Toll Restriction Override for System Speed Dialling
Toll Restriction Override by Account Code Entry
Allows you to temporarily override toll restriction and make a toll call from a toll-
restricted telephone.  You can carry out this feature by entering an appropriate account
code before dialling a telephone number.  For operation procedure,refer to “Account
Code Entry.”
Conditions
•This feature changes the toll restriction level to level 2.  This can be used by
extension users assigned restriction levels from 3 through 8.  Levels 1 and 2 are not
changed.
•A “Class of Service”which is assigned “Account Code Entry — Verified - Toll
Restriction Override”mode permits the class members to override their toll
restrictions.
•Up to forty account codes can be programmed for Verified mode.
•If you do not enter an account code or you enter an invalid account code,standard toll
restriction is in effect.
Programming References 
•Station Programming (Section 2)
Charge Fee Reference — Account Code Set
•System Programming — Installation Manual
[105]Account Codes
[500]–[501]Toll Restriction Level — Day/Night
[508]Account Code Entry Mode
[601]Class of Service
Feature References
Account Code Entry
Toll Restriction (
®see Installation Manual) 
						

							SLT and ISDN Telephone Features7-85
7.2SLT and ISDN Telephone FeaturesT
Toll Restriction Override for System Speed Dialling
Calls originated by “System Speed Dialling”are restricted depending on the extension’s
toll restriction level.
Programming References 
•System Programming — Installation Manual
[509]–[510]Toll Restriction Level for System Speed Dialling — Day/Night
Feature References
System Speed Dialling
Toll Restriction (®see Installation Manual) 
						

							7-86SLT and ISDN Telephone Features
T7.2SLT and ISDN Telephone Features
Trunk (CO Line) Answer From Any Station (TAFAS)
Allows you to answer an incoming outside call,paged through an external pager,from
any extension.
While hearing a tone from the external pager;
1.Lift the handset.
2.Dial the feature number(42).
3.Dial the external pager number as follows.
-1 or 2:if you are connected to the KX-TD816
-1 through 4:if you are connected to the KX-TD1232
•You hear a confirmation tone (optional).
•The line is connected and you can start talking.
Conditions
•This feature can be used in the following cases:
a)The floating number* of an external pager is assigned as the DIL 1:1 destination.
In this case,all the incoming calls on the specified line are signalled.
b)The floating number* of an external pager is dialled as the Direct Dialling In
(DDI) destination.
c)
The floating number* of an external pager is assigned as the Intercept Routing
destination.  In this case,incoming calls redirected to the destination are signalled.
•A confirmation tone is audible before being connected to the caller.  Eliminating the
tone is programmable.
Programming References
•System Programming — Installation Manual
[407]–[408]DIL 1:1 Extension — Day/Night
[409]–[410]Intercept Extension — Day/Night
[813]Floating Number Assignment
[990]System Additional Information,Field (16)
Feature References
Floating Station (®see Installation Manual)
*Floating Number (FN) is a virtual extension number for resources to make it appear to be an extension.  
Refer to the Installation Manual.
1
2
3
external pager number 
						

							SLT and ISDN Telephone Features7-87
7.2SLT and ISDN Telephone FeaturesU
Uniform Call Distribution (UCD)
Allows incoming calls (CO line,extension) to be distributed uniformly to a specific
group of extensions called an UCD group.  Calls to an UCD group queue up,and the
head of the queue searches for an idle extension.
Conditions
•UCD can be used in the following cases:
a)The floating number* of UCD is assigned as the DIL 1:1 destination.
b)The floating number* of UCD is assigned as the Intercept Routing destination.
c)The floating number* of UCD is dialled from the extension.
d)The floating number* of UCD is dialled as the DDI destination.
•The floating number* can be assigned on a hunting group basis and UCD group is
based on the hunting group.
•UCD call can arrive at the extension in log-in status within the UCD group,and
cannot arrive at the extensions in log-out status.
•You can assign the log-in or log-out on the extensions.
Programming References
•System Programming — Installation Manual
[106]Station Hunting Type
Feature Reference
Log-In / Log-Out
*Floating Number (FN) is a virtual extension number for resources to make it appear to be an extension.
Refer to the Installation Manual. 
						

							7-88SLT and ISDN Telephone Features
V7.2SLT and ISDN Telephone Features
1
2
3
4
VM extension number
(X:2 through 5)
1
2
VM extension number
Voice Mail Integration
Allows you to have your calls forwarded to your Voice Processing System mailbox.
Setting Call Forwarding destination to Voice Mail
1.Lift the handset.
2.Dial the feature number(710) and the Call Forwarding
number(2 through 5).
•Each Call Forwarding number corresponds to the following
services:
- 2 :Call Forwarding — All Calls
- 3 :Call Forwarding — Busy
- 4 :Call Forwarding — No Answer
- 5 :Call Forwarding — Busy/No Answer
3.Dial the extension number of the Voice Mail.
•You hear a confirmation tone and then a dial tone.
4.Hang up.
•Calls directed to you are automatically forwarded to your
mailbox.
•Callers can leave their messages in the mailbox,according
to the Voice Mail guidance.
Listening to a stored message
You can listen to the messages stored in your mailbox with ease.
1.Lift the handset.
2.Dial the extension number of the Voice Mail.
•You can listen to the stored message by following the Voice
Mail guidance. 
						

							SLT and ISDN Telephone Features7-89
7.2SLT and ISDN Telephone FeaturesV
Conditions
•Outside callers can leave their messages in your mailbox.  When an incoming outside
call arrives,the operator answers the call and forwards it to your extension.  And...
—If you set a “Call Forwarding”function whose destination is the Voice Mail;
The call will be forwarded to the Voice Mail automatically.
—If you do not set a “Call Forwarding”function;
The call will return to the operator.  Then the operator transfers the call to the
Voice Mail.
•A Voice Mail can be assigned as the destination of the following features:
a)Call Forwarding — All Calls
b)Call Forwarding — Busy
c)Call Forwarding — No Answer
d)Call Forwarding — Busy/No Answer
e)Intercept Routing
Feature References
Call Forwarding — All Calls,Busy,Busy/No Answer,No Answer
Intercept Routing (®see Installation Manual) 
						

							7-90SLT and ISDN Telephone Features
7.3ISDN Telephone Features
The system supports ISDN telephones in addition to proprietary telephones and single
line telephones.  The features are almost the same as ones of the single line telephone.
There are,however,some features that are unavailable for ISDN telephones as shown
below.  As for available features,see Section 7.2,“SLT and ISDN telephone Features.”
Features unavailable for ISDN telephones
•Account Code Entry
Dialling “99”instead of “#”as the delimiter makes this feature available.
•Alternate Calling — Ring/Voice
•Automatic Callback Busy (Camp-On)
•Call Forwarding
•Call Hold
•Call Pickup,Group
•Call Waiting
•Conference
•Do Not Disturb (DND)
•Do Not Disturb (DND) Override
•Doorphone Call
- To unlock the door while talking to the doorphone
•Log-In / Log-Out
•Message Waiting
•Paging — ANSWER
- Answering a page sent to the built-in speaker
•Parallelled Telephone Connection
•Pickup Dialling (Hot Line)
•Station Speed Dialling
•Timed Reminder 
						

							Contents
Basic Operations ............................................................................8-2
Station Programming .....................................................................8-2
User Programming (Manager Programming) ...............................8-9
DPT Features ...............................................................................8-10
Operator Service Features ...........................................................8-22
Special Display Features..............................................................8-25
DECT Portable Station Features .................................................8-31
DSS Console Features ..................................................................8-35
SLT and ISDN Telephone Features ..............................................8-36
Section 8
Quick Reference 
						

							8-2Quick Reference
8Quick Reference
pMaking Calls
—Intercom Calling
•Off-hook.
•Dial the extension number,or press a DSS
button.
—Outward Dialling
•Off-hook.
•Dial 9 or 81 through 88,or press a CO
button.
-9:Line Access,Automatic
-81 – 88:Line Access,CO Line Group
-CO:Line Access,Individual
•Dial the phone number.
pReceiving Calls
•Off-hook.
OR
•Press a flashing CO button directly
(Answering,Direct CO Line),or a flashing
INTERCOM button directly.
lTo enter programming mode
(Be sure the telephone is idle and on-
hook.)
Press:PROGRAM    9    9
lTo exit programming mode
Press:PROGRAM  or lift the handset
pCall Waiting Tone Type Assignment
•Enter the programming mode.
•Dial 5.
•Dial 1 or 2.
- 1 :Call Waiting Tone 1
- 2 :Call Waiting Tone 2
•Press STORE button.
•Exit the programming mode. Off-hook:Lift the handset or press the
SP-PHONE/MONITOR button.
On-hook:Hang up or press the
SP-PHONE/MONITOR button.
This list is divided into the following eight sections.  Refer to each section as needed.
1.)Basic Operations
2.)Station Programming
3.)User Programming (Manager Programming)
4.)DPT Features
5.)Operator Service Features
6.)Special Display Features
7.)DECT Portable Station Features
8.)DSS Console Features
9.)SLT and ISDN Telephone Features
•
When setting “Idle Line Preference — Outgoing,”“No Line Preference — Outgoing,”or “Prime
(CO Line) Preference,”press the INTERCOM button after going off-hook to activate the following
operations. (Pressing the INTERCOM button directly without going off-hook is also available.)
12Basic OperationsStation Programming
 
						

							Quick Reference8-3
8Quick Reference
pCharge Fee Reference
—Extension Charge Fee Reference
•Enter the programming mode.
•Dial 8.
•Enter ID Code.
•Dial 1 + extension number.
•Press SEL (S1) button.
•Press the desired button (CLR,STORE,
NEXT,or PREV),if required.
•Press HOLD (END) button three times.
•Exit the programming mode.
—CO Line Charge Fee Reference
•Enter the programming mode.
•Dial 8.
•Enter ID code.
•Dial 2.
•Dial CO line number as follows.
- 01 - 08 :if connected to the KX-TD816
- 01 -
24 :if connected to the KX-TD1232
•Press SEL (S1) button.
•Press the desired button (CLR,STORE,
NEXT,or PREV),if required.
•Press HOLD (END) button three times.
•Exit the programming mode.
—Account Code Charge Fee Reference
•Enter the programming mode.
•Dial 8.
•Enter ID Code.
•Dial 3 + location number
(01 through 40).
•Press SEL (S1) button.
•Press the desired button (CLR,STORE,
NEXT,or PREV),if required.
•Press HOLD (END) button three times.
•Exit the programming mode.
—Total Extension Charge Fee Reference
•Enter the programming mode.
•Dial 8.
•Enter ID Code.
•Dial 4.  
•Press SEL (S1) button.•Press the desired button (CLR or STORE),
if required.
•Press HOLD (END) button twice.
•Exit the programming mode.
—Total CO Line Charge Fee Reference
•Enter the programming mode.
•Dial 8.
•Enter ID Code.
•Dial 5.  
•Press SEL (S1) button.
•Press the desired button (CLR or STORE),
if required.
•Press HOLD (END) button twice.
•Exit the programming mode.
—Total Account Code Charge Fee
Reference
•Enter the programming mode.
•Dial 8.
•Enter ID code.
•Dial 6.  
•Press SEL (S1) button.
•Press the desired button (CLR or STORE),
if required.
•Press HOLD (END) button twice.
•Exit the programming mode.
—Account Code Set
•Enter the programming mode.
•Dial 8.
•Enter ID code.
•Dial 7 + location number (01 through 40).
•Press CLR (S2) button.
•Enter new account code.
•Press STORE button.
•Press HOLD (END) button twice.
•Exit the programming mode.