Panasonic Kx-Td816e, Kx-td1232e User Manual

							Station Programming2-7
2.2Station Programming
Charge Fee Reference
Allows you to see,print out and clear charges.  Charges are displayed per extension,CO
line,account code,or the total of each can be referred to.  There are seven corresponding
features as follows:
1.)Extension Charge Fee Reference
2.)CO Line Charge Fee Reference
3.)Account Code Charge Fee Reference
4.)Total Extension Charge Fee Reference
5.)Total CO Line Charge Fee Reference
6.)Total Account Code Charge Fee Reference
7.)Account Code Set
Conditions
•System Programming determines the extension that can see charges.
•
An identification code (ID code),set by System Programming,is required to see charges.
•The first display format – Pulse or Pound – is selected by System Programming.  This
can be switched manually at each extension.
•You may use the overlay while programming.  In this case,the HOLD button
becomes the END button and the REDIAL button becomes the PREV button.
•The currency denomination is programmable by System Programming.
Programming References
•System Programming — Installation Manual
[015]Charge Rate Fractional Point Assignment
[016]Charge Rate Assignment
[117]Charge Display Selection
[118]Charge Verification Assignment
[119]Charge Verification ID Code Set
[125]Assignment of Denomination
Extension Charge Fee Reference
Provides you with the display of each extension charge (telephone rate).  You can print
out and clear the displayed meter and charge.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 8.
1
8 
						

							2-8Station Programming
2.2Station Programming
2.Enter the ID Code(4 digits).
•The display shows:
•To erase an incorrect entry,press the CLR (S2) button.
3.Dial 1.
4.Dial the extension numberor press the NEXT(S3) button
until the extension number will be designated.
•The display shows the meter.
 If you assign the extension number 201;
5.Press the SEL(S1) button.
•The display shows the charge in Pounds.

•
Pressing each button corresponds to the following operations:
— CLR(S2) button :To clear the meter and charge of the
displayed extension number.
— STOREbutton :To print out the total meter and charge
of the displayed extension number.
— NEXT(S3) button :
To advance to the extension number
that is assigned at the next jack number.
— REDIAL(PREV) button :To return to the extension
number that is assigned at the
previous jack number.
6.Press the HOLD (END) button.
•The display returns to step 4.
7.Press the HOLD (END) button.
•The display returns to step 3.
8.Press the HOLD (END) button again.
•The display shows the initial programming mode.
— To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
3
4
5
1
extension number
S 1
S 2
S 3
SEL
201:00005
SELCLRNEXT
201:£00001.15
SELCLRNEXT
2
ID Code
Charge Meter
HOLD6
HOLD
HOLD
7
8 
						

							Station Programming2-9
2.2Station Programming
CO Line Charge Fee Reference
Provides you with the display of each CO line charge (telephone rate).  You can print out
and clear the displayed meter and charge.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 8.
2.Enter the ID Code(4 digits).
•To erase an incorrect entry,press the CLR (S2) button.
3.Dial 2.
4.Dial the CO line number (01 through 08) or (01 through 24),
or press the NEXT(S3) button until the CO line number will
be designated.
– 01 through 08 :if you are connected to the KX-TD816
– 01 through 24 :if you are connected to the KX-TD1232
•The display shows the meter.
 If you assign the CO line number 08;
5.Press the SEL(S1) button.
•The display shows the meter in Pounds.

•
Pressing each button corresponds to the following operations:
— CLR(S2) button:To clear the meter and charge of the
displayed CO line number.
— STOREbutton :To print out the total meter and charge of
the displayed CO line number.
— NEXT(S3) button :
To advance to the next CO line number.
— REDIAL(PREV) button :To return to the previous CO
line number.
6.Press the HOLD (END) button.
•The display returns to step 4.
7.Press the HOLD (END) button.
•The display returns to step 3.
8.Press the HOLD (END) button again.
•The display shows the initial programming mode.
— To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
HOLD6 2
3
4
5
2
ID Code
CO line number
CO08:00005
SELCLRNEXT
HOLD
HOLD
7
8 1
8
CO08:£00001.15
SELCLRNEXT
S 1
S 2
S 3
SEL 
						

							2-10Station Programming
2.2Station Programming
Account Code Charge Fee Reference
Provides you with the display of each account code charge (telephone rate).  You can
print out and clear the displayed meter and charge.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 8.
2.Enter the ID Code(4 digits).
•To erase an incorrect entry,press the CLR (S2) button.
3.Dial 3.
4.Dial the location number (01 through 40) or press the NEXT
(S3) button until the location number will be designated.
•The display shows the meter.
 If you assign the location number 01;
5.Press the SEL(S1) button.
•The display shows the charge in Pounds.

•
Pressing each button corresponds to the following operations:
— CLR(S2) button :To clear the meter and charge of the
displayed location number.
— STOREbutton :To print out the total meter and charge
of the displayed location number.
— NEXT(S3) button :To advance to the next location
number.
— REDIAL(PREV) button :To return to the previous
location number.
6.Press the HOLD (END) button.
•The display returns to step 4.
7.Press the HOLD (END) button.
•The display returns to step 3.
8.Press the HOLD (END) button again.
•The display shows the initial programming mode.
— To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
HOLD6 2
3
4
5
3
ID Code
location number
AC01:00005
SELCLRNEXT
HOLD
HOLD
7
8 1
8
AC01:£00001.15
SELCLRNEXT
S 1
S 2
S 3
SEL 
						

							Station Programming2-11
2.2Station Programming
Total Extension Charge Fee Reference
Provides you with the display of the total extension charge (telephone rate).  You can
print out and clear the displayed meter and charge.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 8.
2.Enter the ID Code(4 digits).
•The display shows the meter.
•To erase an incorrect entry,press the CLR (S2) button.
3.Dial 4.
•The display shows the total extension meter.

4.Press the SEL(S1) button.
•The display shows the total extension charge in Pounds.

•Pressing each button corresponds to the following
operations:
— CLR(S2) button :To clear the meter and charge of all
extension number.
— STOREbutton :To print out the total meter and charge
of all extension numbers,and the
individual charges for each extension
number.
5.Press the HOLD (END) button.
•The display returns to step 3.
6.Press the HOLD (END) button again.
•The display shows the initial programming mode.
— To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
EXSM:00450
SELCLR
EXSM:£00099.99
SELCLR
1
2
3
4
5
ID Code
S 1
S 2
S 3
SEL
Charge Meter
8
HOLD
HOLD6
4 
						

							2-12Station Programming
2.2Station Programming
Total CO Line Charge Fee Reference
Provides you with the display of the total CO line charge (telephone rate).  You can print
out and clear the displayed meter and charge.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 8.
2.Enter the ID Code(4 digits).
•The display shows:
•To erase an incorrect entry,press the CLR (S2) button.
3.Dial 5.
•The display shows the total CO line meter.
 
4.Press the SEL(S1) button.
•The display shows the total CO line charge in Pounds.
 
•Pressing each button corresponds to the following
operations:
— CLR(S2) button:To clear the meter and charge of all
CO line number.
— STOREbutton:To print out the total meter and
charge of all CO line numbers,and
the individual charges for each CO
line number.
5.Press the HOLD (END) button.
•The display returns to step 3.
6.Press the HOLD (END) button again.
•The display shows the initial programming mode.
— To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
COSM:00450
SELCLR
COSM:£00099.99
SELCLR
1
2
3
4
5
ID Code
S 1
S 2
S 3
SEL
Charge Meter
8
HOLD
HOLD6
5 
						

							Station Programming2-13
2.2Station Programming
Total Account Code Charge Fee Reference
Provides you with the display of the total account code charge (telephone rate).  You can
print out and clear the displayed meter and charge.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 8.
2.Enter the ID Code(4 digits).
•The display shows:
•To erase an incorrect entry,press the CLR (S2) button.
3.Dial 6.
•The display shows the total account code meter.
 
4.Press the SEL(S1) button.
•The display shows the total account code charge in Pounds.

•Pressing each button corresponds to the following
operations:
— CLR(S2) button:To clear the meter and charge of all
account codes.
— STOREbutton:
To print out the total meter and charge
of all account codes,and the individual
charges for each account code.
5.Press the HOLD (END) button.
•The display returns to step 3.
6.Press the HOLD (END) button again.
•The display shows the initial programming mode.
— To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
ACSM:00450
SELCLR
ACSM:£00099.99
SELCLR
1
2
3
4
5
ID Code
S 1
S 2
S 3
SEL
Charge Meter
8
HOLD
HOLD6
6 
						

							2-14Station Programming
2.2Station Programming
Account Code Set
Allows you to assign the account code.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Dial 8.
2.Enter the ID Code(4 digits).
•The display shows:
•To erase an incorrect entry,press the CLR (S2) button.
3.Dial 7.
4.Dial the location number(01 through 40) or press the NEXT
(S3) button until the location number will be designated.
•If the account code has not been assigned,the display
shows “Not Stored.”
5.Press the CLR(S2) button.
•The message of the display disappears.
6.Dial the new account code(5 digits).
•The display shows:
(— xx:location number)
(— aaaaa:account code
number)
•To erase an incorrect entry,press the CLR (S2) button.
7.Press the STOREbutton.
•The display shows the new account code.
8.Press the HOLD (END) button.
•The display returns to step 3.
9.Press the HOLD (END) button again.
•The display shows the initial programming mode.
— To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Charge Meter
xx:aaaaa
CLRNEXT
1
2
3
4
5
8
ID Code
location number
S 1
S 2
S 3
CLR
7AUTO DIAL
STORE
8
6
account code
HOLD
HOLD
9
7 
						

							Station Programming2-15
2.2 Station Programming
Flexible Button Assignment
Each Flexible (CO, DSS, PF) button on your telephone and on the console can be
assigned as various feature buttons such as an Account Button, DSS Button, or
FWD/DND Button, etc..
The features assignable are limited by the button type.  Please refer to “Flexible
Buttons” in Section 1.1, “Feature Buttons.” “Flexible CO Button Assignment” in System
Programming (program address [005]) can be used for this assignment.
Account Button (Assignment)
Allows you to assign a Flexible (CO, DSS, PF) button as an Account button.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
1. Press the desired 
Flexible(CO, DSS, PF) button which you
wish to assign as the Account button.
2. Dial 6.
• The display shows:
3. Press the STOREbutton.
• The STORE indicator light turns on.
• The display shows the initial programming mode.
— To exit from Station Programming mode: Press [PROGRAM] or lift the handset.1
2
3
6
AUTO DIAL
STORE
Account 
						

							2-16Station Programming
2.2Station Programming
Alert Button (Assignment)
Allows you to assign a Flexible (CO) button as an Alert button.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the desired Flexible(CO) button which you wish to
assign as an Alert button.
2.Dial 87.
•The display shows:
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Conference (CONF) Button (Assignment)
Allows you to assign a Flexible (CO,DSS,PF) button as a Conference (CONF) button.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the desired Flexible(CO,DSS,PF) button which you
wish to assign as the Conference button.
2.Dial 7.
•The display shows:
3.Press the STOREbutton.
•The STORE indicator light turns on.
•The display shows the initial programming mode.
—To exit from Station Programming mode:Press [PROGRAM] or lift the handset.
Conference
1
2
3
AUTO DIAL
STORE
87
1
2
3
AUTO DIAL
STORE
7
Alert