Panasonic Kx-Td816e, Kx-td1232e User Manual

							5-60DECT Portable Station Features
5.5Troubleshooting
PROBLEMREMEDYORPROBLEMSOURCE
The PS does not work. 
The PS does not operate.
The PS does not ring.
You cannot dial.
Static,sound cuts in/out,fades. 
Interference from other electrical units.   
“CS Busy”is displayed.
“PS NOT CONNECTED”is displayed.
You cannot store a phone number and
name in the directory.
The alarm sounds after pressing
(Redial).
“”flashes or beeps tones sound
every 5 seconds during a conversation.
You charged the batteries fully,
but “”flashes.
•The battery is empty.  Charge the batteries fully (p. 5-8).
•
The PS has been cancelled or the PS has not been regis-
tered.  To register the PS,please consult with your dealer.
•The power switch is OFF (m).  Turn it ON (l).
•Ringer volume is set to OFF or VIBRATION.
•The PS is out of range or the Cell Station (CS) is busy.
•The radio channel is busy or a radio communication
error occurred.  Try again later.
•The number which you dialled is restricted by the sys-
tem.  
•The key lock mode is set.  To cancel the mode,
press(Function) for about 2 seconds.
•The radio channel is busy or a radio communication
error occurred.  Try again later.
•Set the PS and CS away from other electrical appli-
ances.
•Move closer to the CS.
•The Cell Station is busy.  Try again later.
•The power switch is set to OFF.
•The PS is out of range.
•The radio channel is busy or a radio communication
error occurred.  Try again later.
•Your entry exceeds the maximum digits or characters.
•Do not pause for over 30 seconds while programming.
•A number is not saved in the Call Log.
•The battery is low.  Charge the batteries fully (p. 5-8).
•Clean the charge contacts and charge again.  
•It is time to change the batteries. Please purchase new
batteries. 
						

							DECT Portable Station Features5-61
5.5Troubleshooting
PROBLEMREMEDYORPROBLEMSOURCE
The PS stops working during operation.
Handover does not work.
The display does not show a strong
radio signal “”even though you are
near the CS.
The alarm sounds during a conversation
while receiving a weak radio signal 
“.”•Turn the power switch OFF (m) and ON (l).  Then try
again. 
•Re-insert the battery and try again.
•You moved to a busy CS or are out of range.
•You moved while not having a conversation (e.g.,while
hearing a busy tone).
•The radio channel is busy or a radio communication
error occurred.
•Normally,the PS user can make a call even with a “”
status.  In this case,the current linked CS is still con-
nected even though another CS is closer.
•The radio signal is weak.  Move closer to the CS. 
						

							5-62DECT Portable Station Features
5.6Safety Instructions
Take special care to follow the safety suggestions
listed below.
Safety
1)Power Source:The charger should be connect-
ed to a power supply only of the type described
in the operating instructions or as marked on
the charger.
2) Non-use Periods:When the portable station
(PS) is not being used,turn the power off.
When left unused for a long period of time,the
charger should be unplugged from the house-
hold AC outlet.
Installation
Environment
1) Water and Moisture:Do not use this PS and
the charger near water – for example,near a
bath tub,washbowl,sink,etc. Damp basements
should also be avoided.
2) Heat:The PS and the charger should be kept
away from heat sources such as radiators,
kitchen ranges,etc. They also should not be
placed in rooms where the temperature is less
than 5°C (41°F) or greater than 40°C (104°F). 
Placement
1)Stacking:Do not place heavy objects on top of
the PS and charger.
2)Foreign Material:Care should be taken so that
objects do not fall onto and liquids are not
spilled into the PS and charger.  Do not subject
the PS and charger to excessive smoke,dust,
mechanical vibration,or shock.
3)Surface:Place the charger on a flat surface.
Battery
To reduce the risk of fire or injury to persons,read
and follow these instructions.
1)Use only the battery specified.
2)Do not dispose of the battery in a fire.  It may
explode.  Check with local waste management
codes for special disposal instructions.
3)Do not open or mutilate the battery.  Released
electrolyte is corrosive and may cause burns or
injury to the eyes or skin.  The electrolyte may
be toxic if swallowed.
4)Exercise care in handling the battery in order
not to short the battery with conductive materi-
als such as rings,bracelets,and keys.  The bat-
tery and/or conductor may overheat and cause
burns.
5)Do not recharge batteries,which are provided
or specified as replacement parts for use with
other products.  The battery may leak corrosive
electrolyte or explode.
6)Do not attempt to rejuvenate the battery pro-
vided with or identified for use with this prod-
uct by heating.  Sudden release of battery elec-
trolyte may occur causing burns or irritation to
eyes or skin.
7)Remove the battery from this product if the
product will not be used for a long period of
time (several months or more).  During this
time the battery could leak in the product.
8)Discard the “dead”battery as soon as possible.
A “dead”battery may leak in the product.
9)Do not store this product,or the battery provid-
ed with or identified for use with this product,
in high temperature areas.  Batteries that are
stored in a freezer or refrigerator for the pur-
pose of extending shelf life should be protected
from condensation during storage and defrost-
ing.  Batteries should be stabilised at room
temperature prior to use after cold storage. 
						

							DECT Portable Station Features5-63
5.6Safety Instructions
For Best Performance
Operating Range
1)The range of operation depends on the topo-
graphy of your office,weather or usage condi-
tions,because signals are transmitted between
the Cell Station (CS) and the portable station
(PS) by radio waves.
2)Normally,you will get greater range outdoors
than indoors.  If there are obstacles such as
walls,noise may interfere with your telephone
calls.  In particular,high metal shelves or rein-
forced concrete walls will shorten your operat-
ing range.
3)A PS may not work if used in places that are
too far from the CS depending on the structure
of the building.
Noise
Occasional noise or interference may occur due to
other sources of electromagnetic radiation,such as
refrigerators,microwave ovens,faxes,TVs,
radios,or personal computers.
If noise affects your telephone calls,keep the PS
away from other electrical appliances.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD,DO
NOT EXPOSE THIS PRODUCT TO RAIN OR
ANY TYPE OF MOISTURE. 
						

							Section 6
DSS Console Features
Contents
6.1 Configuration .......................................................................
6-2
Location of Controls .............................................................6-3
Feature Buttons .....................................................................6-4
6.2 DSS Console Features .........................................................6-5
Station Programming ............................................................6-5
Direct Station Dialling .........................................................6-9
One-Touch Dialling ..............................................................6-9
One-Touch Access for System Features ................................6-9
Call Transfer .......................................................................6-10
ANSWER / RELEASE Button Operation
(KX-T7441 only)........................................................6-11

All illustrations of the DPT (paired digital proprietary telephone) used in
these operating instructions are based on model KX-T7235. 
						

							6-2DSS Console Features
6.1Configuration
With a Directed Station Selection (DSS) Console,you can make or transfer calls and
access system features with the touch of a button.  The DSS Console must be connected
to the Panasonic Digital Super Hybrid System and paired with a DPT.  System
Programming is required to designate the jack numbers of the paired DSS Console and
DPT.  With a paired telephone,you can carry out the following operations using the DSS
Console:
•Direct access to an extension (Direct Station Dialling)
•Quick access to an outside party (One-Touch Dialling)
•Quick access to a system feature (One-Touch Access for System Features)
•Easy transfer to an extension (Call Transfer)
The above functions are enabled simply by pressing buttons on the console which are
pre-programmed as function buttons through Station Programming.
There are three DSS Console models.
Conditions
•The DSS Console and the Digital Proprietary Telephone (DPT) should be placed side
by side on your desk.
•A standard telephone cannot be utilised in conjunction with the DSS Console.
•For System Programming,please consult with your dealer.
Programming References
•System Programming — Installation Manual
[007]DSS Console Port and Paired Telephone Assignment
DSS Buttons
KX-T7440
66KX-T7441
48KX-T7240
32
PF ButtonsNoneNone16
ANSWER ButtonNoneYesNone
RELEASE ButtonNoneYesNone 
						

							DSS Console Features6-3
6.1Configuration
Location of Controls
n KX-T7440
n KX-T7240n KX-T7441
PF (Programmable Feature)
Buttons (01 through 16) DSSButtons with 
Busy Lamp Field (BLF)(01 through 32)
DSSButtons with
Busy Lamp Field (BLF)(01 through 48) DSSButtons with 
Busy Lamp Field (BLF)(01 through 66)
ANSWERButtonRELEASEButton 
						

							6-4DSS Console Features
6.1Configuration
Feature Buttons
DSS Consoles have the following types of Feature Buttons:
DSS Buttons with Busy Lamp Field (BLF)
Used to access extensions.  The BLF indicates the busy or idle status of each extension in
the system.  These buttons can also be changed to other function buttons.
PF (Programmable Feature) Buttons
These buttons are provided with no default settings.  With a paired telephone,you can
program the buttons as other function buttons.
ANSWER Button
Used to answer an incoming call.
RELEASE Button
Used to disconnect the line. 
						

							DSS Console Features6-5
6.2DSS Console Features
Station Programming
PF buttons are provided with no default settings,while each DSS button has a default
setting as follows:
DSS 01 - 32 :extension numbers 201 - 232 (DSS 33 – 66:not stored).
To meet your various needs,DSS buttons can be changed to other function buttons.
Every DSS or PF button can be assigned to another extension number,telephone number
or feature number through Station Programming.
Extension Number Assignment
You can assign the desired extension number to a DSS button.
—Be sure that you are in the Station Programming mode:Press [PROGRAM] [9] [9].
1.Press the desired DSSbutton on the console.
2.Dial 1 on the paired telephone.
3.Enter the desired extension number on the paired telephone.
4.Press the STOREbutton on the paired telephone.
•Repeat steps 1 through 4,to program numbers on other DSS
buttons.
—To exit from the Station Programming mode:Press [PROGRAM] or lift the handset.
AUTO DIAL
STORE
1
2
1
4 3
extension number