Kyocera FS 3040MFP User Manual

							8
8-113
Default Setting (System Menu)
Adding a Destination on One-touch Key
This machine has 11 one-touch keys and you can register 2 destinations to each of them.
The one-touch keys are arranged as shown below:
NOTE: Refer to  One-Touch Key on page 3-3  for how to use them.
Registering new destination
Use the procedure below to register a new destination under a One-touch key.
1In the Send or FAX  screen, press the one-touch key to 
which you want to register the destination and hold it (2 
seconds or longer). Select Key Set. appears.
The screen shown is the one when No.1/No.12 is 
pressed and held.
2Press the U  or V key to select the  key number to which 
you want to register the destination.
3Press the OK  key. The Address Book list screen 
appears.
4Press the  U or  V key to select the destination you want 
to register.
NOTE:  If you want to search from the Address Book, refer 
to  Search in Address Book on page 3-27 .
5Press the OK key. The selected destination is registered 
to the one-touch key.  Registered. is displayed and the 
screen returns to the basic screen.
No.1
No.2No.3 No.4
No.12 No.13 No.14 No.15
No.5 No6No.7 No.8
No.16 No.17 No.18 No.19
No.9 No.10 No.11
SHIFT
No.20 No.21 No.22
Select Key No.:a  b 
*********************
2  No. 12
[ Exit ]
1  No. 1
Addressbook:a  b 
*********************
l Fiala
l Maury[ Menu ]
k Design
Downloaded From ManualsPrinter.com Manuals 
						

							8-114
Default Setting (System Menu)
Editing One-touch Key
Edit/delete the destinations you added to One-touch Key.
Use the procedure below to edit the one-touch key.
1In the Send or FAX screen, press the one-touch key 
where you want to edit the destination and hold it (2 
seconds or longer). Select Key Set. appears.
The screen shown is the one when No.1/No.12 is 
pressed and held.
2Press the U or V key to select the key number where 
you want to edit the destination.
3Press the OK  key. The Key Edit appears.
4Press the U or V key to select [Edit].
NOTE: If you select [Delete] here and press the  OK key, 
you can delete the registration  of the destination. If you 
press [Yes] (the  Left Select key) in the screen that appears, 
Completed.  is displayed and the registration of the 
destination is deleted.
5Press the OK  key. The Address Book list screen 
appears.
6Press the  U or  V key to select the destination you want 
to newly register.
NOTE:  If you want to search from the Address Book, refer 
to  Search in Address Book on page 3-27 .
7Press the OK key. A confirmation screen appears.
Select Key No.:a  b 
*********************
2  No. 12
[ Exit ]
1  No. 1
Key Edit:a  b 
*********************
2  Detail
3  Delete[ Exit ]
1  Edit
Addressbook:a  b 
*********************
l Fiala
l Maury [ Menu ]
k Design
Overwrite.
Are you sure?
z No. 1
[ Yes ] [ No ]
Downloaded From ManualsPrinter.com Manuals 
						

							8
8-115
Default Setting (System Menu)
8Press [Yes] (the Left Select key). The selected 
destination is registered  to the one-touch key, 
overwriting the previous one.  Registered. is displayed 
and the screen returns to the basic screen.
Downloaded From ManualsPrinter.com Manuals 
						

							8-116
Default Setting (System Menu)
Restarting the System
Restart the printer without turning the main power switch off. 
Use this to deal with any unstable operation by the machine. 
(Same as the computer restart.) 
Use the procedure below to restart the system.
1In the Sys. Menu/Count. menu, press the  U or V  key to 
select [System], and press the  OK key.
A login screen will appear. Then , enter the user ID and 
password with administrator  privileges to log in, and 
press [Login] (the  Right Select key).
2The System menu appears.
3Press the U or V key to select [Restart].
4Press the OK  key. A confirmation screen appears.
5Press [Yes] (the  Left Select key). The printer is 
restarted.
If you press [No] (the  Right Select key), the printer does 
not restart and the screen returns to the System menu.
Sys. Menu/Count.:a  b 
1  Report
2  Counter
*********************
[ Exit ]
3  System
Login User Name:L  b 
*******************
Login Password:
[ Login ]
System:a  b 
*********************
2  I/F Block Set.
3  Security Level[ Exit ]
1  Network Setting
Restart.
Are you sure?
[ Yes ] [ No ]
Downloaded From ManualsPrinter.com Manuals 
						

							8
8-117
Default Setting (System Menu)
Network Setup
The following network settings are available.
• LAN Interface Setup …8-117
• TCP/IP (IPv4) Setup …8-118
• TCP/IP (IPv6) Setup …8-127
• NetWare Setup …8-128
• AppleTalk Setup …8-129
• Protocol Detail …8-133
LAN Interface Setup
Specify the settings for the LAN interface to be used. The default setting is Auto.
Use the procedure below to select the interface.
1In the Sys. Menu/Count. menu, press the  U or V  key to 
select [System], and press the  OK key.
A login screen will appear. Then , enter the user ID and 
password with administrator  privileges to log in, and 
press [Login] (the  Right Select key).
2The System menu appears.
3Press the U or V key to select [Network Setting].
4Press the OK  key. The Network Setting menu appears.
5Press the U or V key to select [LAN Interface].
Sys. Menu/Count.:a  b 
1  Report
2  Counter
*********************
[ Exit ]
3  System
Login User Name:L  b 
*******************
Login Password:
[ Login ]
System:a  b 
*********************
2  I/F Block Set.
3  Security Level[ Exit ]
1  Network Setting
Network Setting:a  b 
*********************
2  NetWare
3  AppleTalk
1  TCP/IP Setting
Downloaded From ManualsPrinter.com Manuals 
						

							8-118
Default Setting (System Menu)
6Press the OK key. LAN Interface appears.
7Press the U or V key to select the desired LAN 
interface.
The available LAN interfaces are as follows:
Auto
10Base-Half
10Base-Full
100Base-Half
100Base-Full
8Press the OK  key. Completed.  is displayed and the 
screen returns to the Network Setting menu.
TCP/IP (IPv4) Setup
Set up TCP/IP to connect to the Windows network. Set  the IP addresses, subnet masks, and gateway addresses. 
The default settings are TCP/IP Protocol: On , DHCP: On, Bonjour:  Off.
NOTE: Prior to the IP address entries, obtain permission from the network administrator.
Use the procedure below to setup the TCP/IP (IPv4) setting.
1In the Sys. Menu/Count. menu, press the  U or V  key to 
select [System], and press the  OK key.
A login screen will appear. Then , enter the user ID and 
password with administrator  privileges to log in, and 
press [Login] (the  Right Select key).
2The System menu appears.
LAN Interface:a  b 
*********************
2  10Base-Half
3  10Base-Full
1 *Auto
Sys. Menu/Count.:a  b 
1  Report
2  Counter
*********************
[ Exit ]
3  System
Login User Name:L  b 
*******************
Login Password:
[ Login ]
System:a  b 
*********************
2  I/F Block Set.
3  Security Level[ Exit ]
1  Network Setting
Downloaded From ManualsPrinter.com Manuals 
						

							8
8-119
Default Setting (System Menu)
3Press the U or V key to select [Network Setting].
4Press the OK  key. The Network Setting menu appears.
5Press the U or V key to select [TCP/IP Settings].
6Press the OK  key. The TCP/IP Settings menu appears.
7Press the U or V key to select [TCP/IP].
8Press the OK  key. TCP/IP appears.
9Press the U or V key to select [On] and then press the 
OK  key.
Completed.  is displayed and the screen returns to the 
TCP/IP Settings menu.
10Press the U  or V key to select [IPv4 Setting].
11Press the OK  key. The IPv4 Setting menu appears.
12Press the U or V key to select [DHCP].
Network Setting:a  b 
*********************
2  NetWare
3  AppleTalk
[ Exit ]
1  TCP/IP Settings
TCP/IP Settings:a  b 
*********************
2  IPv4 Setting
3  IPv6 Setting[ Exit ]
1  TCP/IP
TCP/IP:             a  b 
1  Off
*********************2 *On
TCP/IP Settings:a  b 
1  TCP/IP
*********************
3  IPv6 Setting[ Exit ]
2  IPv4 Setting
IPv4 Setting:a  b 
*********************
2  Bonjour
3  IP Address[ Exit ]
1  DHCP
Downloaded From ManualsPrinter.com Manuals 
						

							8-120
Default Setting (System Menu)
13Press the OK key. DHCP appears.
14Press the U or  V key to select [Off ] and then press the 
OK  key. 
Completed.  is displayed and the screen returns to the 
IPv4 Setting menu.
15Press the U  or V key to select [Bonjour].
16Press the OK  key. Bonjour appears.
17Press the U or  V key to select [Off ] and then press the 
OK  key. 
Completed.  is displayed and the screen returns to the 
IPv4 Setting menu.
18Press the U  or V key to select [IP Address].
19Press the OK  key. IP Address appears.
20Use the arrow keys to enter the IP address. 
Press the Y or  Z key to move the  cursor position 
horizontally.
DHCP:               a  b 
1  Off
*********************2 *On
IPv4 Setting:a  b 
1  DHCP
*********************
3  IP Address
[ Exit ]
2  Bonjour
Bonjour:a  b 
*********************
2  On
1 *Off
IPv4 Setting:a  b 
1  DHCP
2  Bonjour
*********************
[ Exit ]
3  IP Address
IP Address:a  b 
   
000.000.000.000
Downloaded From ManualsPrinter.com Manuals 
						

							8
8-121
Default Setting (System Menu)
Press the U or V key or the numeric keys to enter the 
IP Address. Each 3 digits can be set between 000 and 
255.
IMPORTANT:  When the DHCP Setting ( page 8-123) is [On], 
the current IP address is displayed and cannot be changed.
When setting an IP address, set the DHCP Setting ( page 8-
123) to Off.
21Press the OK  key. Completed.  is displayed and the 
screen returns to the IPv4 Setting menu.
22Press the U  or V key to select [Subnet Mask].
23Press the OK  key. Subnet Mask appears.
24Use the arrow keys to enter the Subnet Mask.
Press the Y or  Z key to move the  cursor position 
horizontally.
Press the U  or V key or the numeric keys to enter the 
Subnet Mask. Each 3 digits can be set between 000 and 
255.
IMPORTANT:  When the DHCP Setting ( page 8-123) is [On], 
the current Subnet Mask is displayed and cannot be 
changed.
When setting an Subnet Mask, set the DHCP Setting ( page 
8-123) to Off.
25Press the OK  key. Completed.  is displayed and the 
screen returns to the IPv4 Setting menu.
26Press the U  or V key to select [Default Gateway].
IP Address:  b 
   123.145.167.189
IPv4 Setting:a  b 
3  IP Address
*********************
5  Default Gateway [ Exit ]
4  Subnet Mask
Subnet Mask:a  b 
   
000.000.000.000
IPv4 Setting:a  b 
3  IP Address
4  Subnet Mask
*********************
[ Exit ]
5  Default Gateway
Downloaded From ManualsPrinter.com Manuals 
						

							8-122
Default Setting (System Menu)
27Press the OK key. Default Gateway appears.
28Use the arrow keys to enter the Default Gateway.
Press the Y or  Z key to move the  cursor position 
horizontally.
Press the U  or V key or the numeric keys to enter the 
Default Gateway. Each 3 digits can be set between 000 
and 255.
IMPORTANT:  When the DHCP Setting ( page 8-123) is [On], 
the current Default Gateway is displayed and cannot be 
changed.
When setting an Default Gate way, set the DHCP Setting 
(page 8-123 ) to Off.
29Press the OK  key. Completed.  is displayed and the 
screen returns to the IPv4 Setting menu.
Default Gateway:a  b 
   
000.000.000.000
Downloaded From ManualsPrinter.com Manuals