TiE Onyx 2, 3, 4, 5 Service And Programming Manual

							Q-   
 MUSIC/RELAY  EST  AUDIBLE LINE
Description
Related
Programming
l
l
l
l
l
l
In the large  use this option to assign the trunk number the system
 use to broadcast All Call  and  Audible. You  use the
trunk circuit 
  for  other purpose. Refer to the system
  for additional installation details. This option is
independent of the 
 Relay Control options.
 VS. this option is EXTERNAL  AUDIBLE. Enter  to enable
All Call Paging and Night Audible on the main CEU PA terminals. Enter
N(o) to disable Paging and audible.
Conditions
None
Default Value
No trunk assigned (00).
Night Answer, Universal Night Answer
E- Extensions, ED- Trunk Control, Access Control 
 An extension allows
UNA pickup only for trunks to which it has access.
E- Trunks, Et- Circuit Type 
 The unused trunk circuit assigned in QM
below must have circuit type X.
E- Trunks, 
 Direct Trunk  Night Call Routing 
Terminate each trunk to the main attendant (extension  00).
Q&i- 
 and  Control. Inhibit Audible Ring  Enable audible ring
on the night audible port.
Paging, External
E- Trunks, 
 Circuit Type  Program the ports used for External Paging as
uninstalled (circuit type X).
QM- Music and Relay Control, Page Zone n Line Number (except in 
 Assign a trunk port for External Paging zones 1-3.  Call Paging also
broadcasts over these ports.
QM-  and Relay Control, External Page (VS only)  Enter Y to have
External Paging zone 
 and All Call broadcast over the expansion CEU PA
terminals.
 Music and Relay Control, External Page Music Gain  Adjust the
gain for the music that plays over the External Paging ports.
(Program the next two 
 for each of the four relays.)
 Music and Relay Control, Relay Control-Page On (except in   If
enabled and Pageowner is main attendant (port 
  relay closes
each time a user makes an All Call Paging announcement. If disabled 
Pageowner is other than the attendant. relay never closes for Paging.
  and  Control, Relay Control-Pageowner  Assign the
Pageowner for ringer and page control.
Issue 1-OSOFTWARE CONFIGURATION Z-295 
						

							Q- SYSTEM WIDE PROGRAMMING
QM- MUSIC/RELAY CONTROL, ENT PAGE/NIGHT AUDIBLE LINE
Related
Programming
(Cont’d)
l
Feature Reference
Instructions
Step I l
 1 l
Step 2 l
Tenant Service. Assigning  Paging Zones to Tenants
E- Extensions, El- Circuit   Program the ports used for External
Paging as uninstalled (circuit type X). There are a total of four ports available
for External Paging.
  and  Control. Page Zone n Line Number (except in VS)
 Assign a trunk port for External Paging zones 1-3.  Call Paging also
broadcasts over these ports. You have three external zones available for
tenants.
  and Relay Control,  Page (VS only)  Enter Y to have
All Call Paging and Night Audible broadcast over the expansion CEU PA
terminals.
  and  Control,  Page Music Gain  Adjust the
gain for the music that plays over the External Paging ports (if any).
 Musk and Relay Control, Relay Control-Page On (except in   If
enabled and Pageouner is main attendant (port OO/extension 
 relay closes
each time a user makes an All Call Paging announcement. If disabled or
Pageowner is other than the attendant. relay never closes for Paging.
 Music and Relay Control. Relay Control-Pageowner  Assign the
Pageowner for ringer and page control. This assignment should be the
attendant in each tenant group.
Night Answer
Paging
Tenant Service
To enter data on the PRF:
For QM- Ext All Page/Night Audible Line Number on Table 10, enter the
External All Page/Night Audible trunk circuit number.
To enter data at the programming terminal:
After programming QM- MOH Line Number, you see: 
 ALL PAGE/NIGHT
AUDIBLE (LINE NUMBER)
Enter the QM- Ext All Page/Night Audible Line Number from Table 10 from
Table 10 and press 
RETURN. You see: INHIBIT AUDIBLE RING?To erase an entry. enter 
Go to QM- Inhibit Audible Ring on the next page.
In  you enter Y(es) or N(o). 
						

							Q- SYSTEM WIDE PROGRAMMING
  CONTROL, INHIBIT AUDIBLE RING
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step  
Step  l
Use this option to enable/disable audible ring on the trunk port you designate
in QM- Est 
 Audible Line Number. If enabled (N), night 
can occur over the trunk port. If disabled (Y). night audible cannot occur.
Conditions
None
Default 
Audible ring enabled (N).
 Answer. Universal Night Answer
E- Extensions. ED- Trunk Control, 
 Control  An extension allows
UNA pickup only for trunks to which it has access.
E- Trunks, 
 Circuit   The unused trunk circuit assigned in QM
below must have circuit type X.
E- Trunks, 
 Direct Trunk  Night Call Routing 
Terminate each trunk to the main attendant (extension  00).
 Music and Relay Control,  Page/Night Audible Line Number  In
the large systems. indicate the unused trunk circuit that will broadcast night
audible. In VS. enter Y. An incoming call will activate ringing on the night
audible port if:
 The ringing trunk is terminated (in  to the main attendant (extension
300)
 The main attendant is in the night mode
Night Answer
To enter data on the PRF:
For QM- Inhibit Audible Ring on Table 10, enter Y or N.
To enter data at the programming terminal:
After programming QM- Ext Page/Night Audible Line Number, you see:
INHIBIT AUDIBLE RING?
Enter Y or N for QM- Inhibit Audible Ring from Table 10. You see:
EXTERNAL PAGE PORTS, ZONE 1 LINE NUMBER?
Go to QM- Page Zone n Line Number on the next page.
Issue 1-OSOFTWARE CONFIGURATION 2-297 
						

							Q- SYSTEM WIDE 
QM- MUSIC/RELAY CONTROL,   n LINE 
Description
Related
Programming
l
l
l
l
. 
l
Use this option to assign the trunk circuits the system will use for external
Paging zones 
You should assign a different trunk for each of the three
zones. You cannot use the trunk circuits you designate here for any other
purpose. (Note that All Call Paging also broadcasts over these trunks.) Refer
to the system 
  for additional installation details. This option
is independent of the QM- Relay Control options.
This option does not apply to VS.
Conditions
None
Default 
No trunk circuits assigned (00).
Paging, External.
E- Trunks,  Circuit Type  Program the ports used for External Paging as
uninstalled (circuit type X).
QM- Music and Relay Control, Ext Page/Night Audible Line Number  In
large systems, assign the trunk number the system will use to broadcast All
Call Paging and 
 Audible. In VS, enter Y to have All Call Page
broadcast over the main CEU PA terminals.
  and Relay Control, External Page (VS only)  Enter Y to have
External Paging zone 1 and All Call broadcast over the expansion CEU PA
terminals.
 Music and Relay Control, External Page Music Gain  Adjust the
gain for the music that plays over the External Paging ports.
(Program the next two 
 for each of the four relays.)
QM- 
 and Relay Control, Relay Control-Page On (except in VS)  If
enabled and Pageowner is main attendant (port OO/extension  relay closes
each time a user makes an All Call Paging announcement. If disabled or
Pageowner is other than the attendant, relay never closes for Paging.
QM- Music and Relay Control, Relay Control-Pageowner  Assign the
Pageowner for ringer and page control.
Tenant Service, Assigning External Paging Zones to Tenants
E- Trunks, 
 Circuit Type  Program the ports used for External Paging as
uninstalled (circuit type X). There are a total of four ports available for
External Paging.
 Music and Relay Control, Ext Page/Night Audible Line Number  In
the large systems, assign the trunk number the system will use to broadcast
All Call Paging and Night Audible. In VS, enter Y to broadcast over the main
CEU PA terminals. You can have Paging amplifiers for all tenants or just
those you select. You can have Paging amplifiers for all tenants or just those
you select.
 Music and Relay Control, External Page (VS only)  Enter Y to have
 Call Paging and Night Audible broadcast over  CEU PA
terminals.
  and Relay Control, External Page Music Gain  Adjust the
gain for the music that plays over the External Paging ports (if any). 
						

							Q-  WIDE PROGRAMMING
 MUSIC/RELAY  PAGE ZONE  LINE NUMBER
Related
Programming
l
l
Feature Reference
Instructions
Step  
Step 
Step  
Step 3 
Step  l
  and Relay Control, Relay Control-Page On  on  
If enabled and Pageowner is main attendant (port OO/extension 300). relay
closes each time a user makes an All Call  announcement. If disabled
or Pageowner is other than the attendant. relay never closes for Paging.
  and  Control, Relay Control-Pageowner (Owner in 
  the  for ringer and page control. This assignment should
be the attendant 
 each tenant group.
Paging
Tenant Service
To enter data on the PRF:
For QM- Zone 1 Line 
 on Table  enter the trunk circuits used for
External Page zones 1-3.
To enter data at the programming terminal:
After 
 QM- Inhibit Audible Ring, you see: EXTERNAL PAGE
PORTS, ZONE 
 LINE NUMBER
Enter the QM- Zone 1 Line Number entry from Table 10 and press RETURN.
 see: ZONE 2 LINE NUMBER.To erase an assignment. enter 00.
Enter the QM- Zone 2 Line Number entry from Table 10 and press RETURN.
You 
see: ZONE 3 LINE NUMBERTo erase an assignment, enter 00.
Enter the QM-  3 Line Number entry from Table 10 and press RETURN.
You 
see: BGM TO ALL  PAGE ZONESTo erase an assignment, enter 00.
Go to QM- BGM on External Page Zones on the next page.
Issue 1-OSOFTWARE CONFIGURATION 2-299 
						

							Q- SYSTEM  
  CONTROL. EXTERNAL   ONLY)
Description
Related
Programming
l
l
l
Use this option to  External Paging on the expansion CEU PA
terminals. 
 enabled (Y).  Paging zone 1 and All Call broadcast over
the expansion 
 PA terminals. If disabled (N), paging does not broadcast
 the espansion   PA  terminals. Refer to the system Hardware Manual
for 
 installation details.
This option only applies to VS.
Conditions
External Paging uses the fourth trunk circuit on the first CO Module in each
CEU. You cannot use these circuits for trunks. Refer to the system Hardware
Manual for External Paging installation details.
Default  
Paging not  (N).
Paging, External
E- Trunks,  Circuit   Program the ports used for External Paging as
uninstalled (circuit type X).
  and Relay Control, Ext Page/Night Audible Line Number  In
large systems,  the trunk number the system will use to broadcast All
Call Paging and 
 Audible. In VS, enter Y to have All Call Page
broadcast over the main CEU PA terminals.
  and Relay Control, External Page Music Gain  Adjust the
gain for the music that plays over the External Paging ports.
(Program the next two 
 for each of the four relays.)
 Music and Relay Control, Relay Control-Pageowner (Owner in 
 Assign the Pageowner for ringer and page control.
Tenant Service, Assigning External Paging Zones to Tenants
E- Trunks, 
 Circuit Type  Program the ports used for External Paging as
uninstalled (circuit type X). There are a total of four ports available for
External Paging.
 Music and Relay Control, Ext Page/Night Audible Line Number  In
the large systems, assign the trunk number the system will use to broadcast
All Call Paging and Night Audible. In VS, enter Y to broadcast over the main
CEU PA terminals. You can have Paging amplifiers for all tenants or just ----
those you select. You can have Paging amplifiers for all tenants or just those
you select.
  and Relay Control, External Page Music Gain -Adjust the
gain for the music that plays over the External Paging ports (if any).
.
Issue 1-O 
						

							Q- SYSTEM WIDE PROGRAMMING
   EXTERNAL PAGE  ONLY)
Feature Reference
Instructions
Step  l
Step I l
Step  
Issue 1-O
  and Relay Control.  Control-Pageouner (Owner in 
 Assign the  for ringer and page control. This assignment should
be the attendant in each tenant group.
Paging
Tenant Service
To enter data on the PRF:
For QM- External Page on Table 10. Y(es) or N(o).
To enter data at the programming terminal:
After programming QM- Inhibit Audible Ring, you see: 
EXTERNAL PAGE
PORTS, EXTERNAL PAGE
Enter  or N(o) for QM- External Page from Table 10 and press RETURN.
You 
see:  TO ALL EXT PAGE ZONES.Go to QM- BGM on External Page Zones on the next page.
SOFTWARE   
						

							Q-  WIDE 
 MUSIC/RELAY CONTROL,  ON EXTERNAL PAGE ZONES
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step I 
Step 2 
Use this option to  Background Music to play over the External
Paging zones. If 
  BGM  play over all the external zones (All
Call and    are idle.  disallowed. BGM will not  Refer to
the svstem 
 Manual and the Background Music feature for
 information on Background Music.
Always make a “test” page after enabling this option.
Default 
BGM will not play over External Page zones (N).
None
None
To enter data on the 
For QM- BGM to All Ext Page Zones on Table 10, enter Y or N.
To enter data at the programming terminal:
After making an entry for QM- Zone 3 Line Number, you see: 
 TO ALL
 PAGE ZONES
Enter  or N for QM- BGM to All Ext Page Zones from Table 10. You see:
INTERRUPTED RING RELAYS?
Go to QM- Interrupted Ring Relays on the next page.
    1-O 
						

							Q-  WIDE PROGRAMMING
  CONTROL, INTERRUPTED RING RELAYS
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step  
Step 2 
Issue 1-O .Use this option to enable/disable interrupted closure for the external relays
when used for ringing. If enabled 
  pulse one second closed/three
seconds open when activated. If disabled 
 relays have continuous closure
when activated. This option affects all the external relays. All external relays
are normally open.
Conditions
None
Default Value
Relays provide continuous closure (N) when activated.
For each of the four relays (O-3):
 Music and Relay Control, Relay Control-Ringer On (except in VS)
If enabled and Pageowner is main attendant (port 
 300). relay
activates for UNA calls. If Pageowner is an extension other than the 
attendant. relay activates when extension rings. If disabled, relay never closes
for ringing.
  and  Control. Relay Control-Page On (except in   If
enabled and Pageowner is main attendant (port 
  relay closes
each time a user makes an All Call Paging announcement. If disabled or
Pageowner is other than the attendant. relay never closes for Paging.
  and Relay Control, Relay Control-Pageowner  Assign the
Pageowner for ringer and page control.
External Alerting Devices
To enter data on the PRF:
For QM- Interrupted Ring Relays on Table 10, enter Y or N.
To enter data at the programming terminal:
After programming QM- BGM to 
 Ext Page Zones, you see:
INTERRUPTED RING RELAYS
Enter Y or N for QM- Interrupted Ring Relays on Table 10.If you entered  for QM- BGM on External Page Zones, go to QM- External PageMusic Gain on the next page.
 vou entered N for QM- BGM on External Page Zones, go to QM- Relay Control-Ringer On.
SOFTWARE CONFIGURATION2-301 
						

							Q-   PROGRAMMING
  CONTROL.   MUSIC GAIN
Description
Note:
Related
Programming
l
Use this option to adjust thegain for the Background  that  over
the External 
 ports.
The adjustment you make  this option does not
affect the 
  internal Background  You can make fine
adjustments to internal and 
   separately. The choices
are:
-l’dB loss
-6 
 loss
-3 
 loss
0 
  gain
  gain
This option 
 appears if  enter Y fo
Zones.
 QM- BGM on Extema Page
A 3 
 gain   doubles the BGM volume on the external port. A 3 
loss (-3  cuts the volume in half.
Conditions
None
Default Value
 6  loss
Paging, External
E- Trunks,  Circuit  Program the ports used for External Paging as
uninstalled (circuit type X).
 Music and Relay Control, Ext Page/Night Audible Line Number  In
large systems, assign the trunk number the system will use to broadcast All
Call Paging and Night Audible. In VS, enter Y to have All Call Page
broadcast over the main CEU PA terminals.
QM- Music and Relay Control, Page Zone n Line Number (except in 
 Assign a trunk port for External Paging zones l-3. All Call Paging also
broadcasts over these ports.
QM- Music and Relay Control, External Page (VS only)  Enter Y to have
External Paging zone 1 and All Call broadcast over the expansion CEU PA
terminals.
QM-  and Relay Control, Relay Control-Page On (except in   If
enabled and Pageowner is main attendant (port   relay closes
each time a user makes an All Call Paging announcement. If disabled 
Pageowner is other than the attendant, relay never closes for Paging.
  and Relay Control, Relay Control-Pageowner (Owner in 
 Assign the Pageowner for ringer and page control.