TiE Onyx 2, 3, 4, 5 Service And Programming Manual

							E- EXTENSIONS
ED- TRUNK CONTROL, ACCESS CONTROL
Related
l
l
Central Office Calls. Placing
E- Extensions, ES- Line 
 Options,  Access to Outbound Lines 
If enabled, user can press a line key to place a call (if also allowed by ED
programming).
E- Extensions, ES- Line Access Options, Allow Line Code Dial-Up 
 If
enabled, user can dial a trunk access code (e.g., 801) to access trunks (if also
allowed by ED programming).
E- Extensions, ES- Line Access Options, Access to Groups 90-95 (not on
key systems) 
 If enabled. user can dial 90-95 to access trunk groups 1-6.
E- Extensions, ED- Trunk Control, Call-Out Control 
 Enable call-out for
each trunk on which the user should be able to place calls.
E- Trunks, 
 Circuit Type  Program the correct circuit type for each
trunk.
KS- Programming 
 for  Program the types of keys that allow
the extension user to place trunk calls.
Direct Inward Dialing
CP- Absorb 1st Digit for DID and Tie Trunks 
 If QO- DID
Intercepts (Absorb 1st Digit) is off(N), use this option to apply 1st digit
absorption on a trunk-by-trunk basis. When you enable this option, the trunk
is compatible with four digit DID service. 
This is  COS option for DID
CP- Allow Automatic Operator Intercept for DID (BYO:O) 
Enable/disable All Call Intercept in an extension’s COS. This is a COS option
for extensions.
E- Extensions, ED- Trunk Control, Ring Control  The attendant assigned
to each DID trunk should have ringing for the trunk. This allows the
intercepts to work properly. However, intercepts to 
 work fine without
ring programmed.
E- Extensions/Trunks, 
 Class of Service  Assign Class of Service to
DID trunks and extensions.
E- Trunks, 
 Circuit Tvpe  Assign DID trunks with circuit type 07.
E- Trunks, 
   Number  Enter the STI circuit number for the
DID trunk. Refer to the 
 Installation and Programming Manual for charts
and drawings that explain this correlation,
KS- Programming Keys for 
 Each extension should have a line key
for DID trunks or a loop key.
Direct Trunk Access
CP- Direct Trunk Access and Trunk Camp O N  
  Enable/disable
Direct Trunk Access in Class of Service
E- Extensions, 
 Class of Service  Assign Class of Service to extensions.
E- Extensions, ED- Trunk Control, Call-Out Control 
 Enable call-out for
each trunk that the user should be able to seize using Direct Trunk Access.
Night Answer, Assigned Night Answer
E- Extensions, ED- Trunk Control, Ring Control-: For each 
designate the ringing options for each trunk. Use the N option to have the
trunk only ring the 
 at night.
E- Trunks, EI- Night Call Routing 
 Define the night call route for each
trunk. This option overrides ED- Ring Control assignments at night. It also
lets night mode calls ring 
 extensions.
Issue 1-O CONFIGURATION2-121 
						

							E- EXTENSIONS
ED- TRUNK CONTROL, ACCESS CONTROL
Related
Programming
(Cont’d)
l
l
l
Night Answer, Universal Night 
E- Trunks,  Circuit Type  The unused trunk circuit assigned in QM
below must have circuit type X.
 Music and Relay Control. Ext Page/Night Audible Line Number  In
the large systems, indicate the unused trunk circuit that will broadcast night
audible. In VS, enter Y. An incoming call will activate ringing on the night
audible port if:
 The ringing trunk is terminated (in E9) to the main attendant (extension
300)
 The main attendant is in the night mode
  and Relay Control, Inhibit Audible Ring  Enable audible 
on the night audible port.
Prime Line Selection
E- Extensions, ES- Line Access Options, Key Access to Outbound Lines 
The extension must have outbound line key access to use the Prime Line key
for placing calls.
E- Extensions, ED- Trunk Control, Call-Out Control  For outgoing calls,
the extension must have call-out enabled for the trunk appearing on the Prime
Line key.
E- Extensions, EL- Prime Line Kev  Enter the Prime Line key number 
 followed bv the option. The options are:
R Ringing Prime Line
I Idle Prime Line
KS- Programming Keys for   Program the Prime Line key as a line
key.
Private Line
E- Extensions, 
 Line Access Options, Key Access to Outbound Lines 
Enable outbound access to allow the  user to place calls on the Private
Line (if also allowed by ED programming).
E- Extensions, ED- Trunk Control, Ring Control  Enable/disable ringing
for the Private Line. Assign ringing only for those extensions that have the
Private Line.
E- Extensions, ED- Trunk Control, Call-Out Control  Enable call-out if
the extension user should be able to place calls on the Private Line. Enable
 only for those extensions that have the Private Line.
E- Trunks,  Circuit Type Program the correct circuit type for the
Private Lines.
KS- Programming  for   Assign the Private Line to a
programmable key. 
 the key only on those extensions that should have
the Private Line.
Tenant Service, Assigning Trunks to Tenants for Answering Calls
E- Extensions, ED- Trunk Control, Ring Control 
 For each  in the
tenant group, designate the ringing options for each trunk. Each tenant group
should ring for a different set of trunks,
KS- Programming Kevs for   Program  of keys that will
ring the extension. 
 make sure that every  has at least one
fixed or switched loop key. This ensures that an incoming call will ring a key
somewhere on the 
2-122 SOFTWARE CONFIGURATIONIssue 1-O 
						

							E- EXTENSIONS
ED- TRUNK CONTROL, ACCESS CONTROL
Related
Programming
l
l
P
l
l
Feature ReferenceTenant 
 Assigning Trunks to Tenants for Placing Calls
 Extensions, ES- Line Access Options.   to Outbound Lines 
If enabled, each user in the tenant group can press a line  to place a call (if
also allowed 
 ED programming).
E- Extensions, ES- Line Access Options, Allow Line Code Dial-Up 
 If
enabled, each user in the tenant group can dial a trunk access code (e.g., 801)
to access trunks (if also allowed by ED programming).
 Extensions,  Line Access Options.  to Groups  (not on
 systems)  Restrict each extension in the tenant group to the trunk groups
(90-95) that tenant should be able to dial.
 Extensions. ED- Trunk Control, Call-Out Control  Enable call-out for
each trunk on which the tenant group user should be able to place calls. Each
tenant group should have 
 for a different set of trunks.
KS- Programming 
 for  Program the types of keys that allow
the extension user to place trunk calls.
Call Parking
Central Office Calls, Answering
Central Office Calls, Placing
Direct Inward Dialing
Direct Trunk Access
Night Answer, Assigned Night Answer
 Answer, Universal Night Answer
 Line Selection
Private Line
Tenant Service
Issue 1-OSOFTWARE CONFIGURATION2-123 
						

							E- EXTENSIONS
ED- TRUNK CONTROL, ACCESS CONTROL
Instructions
Step  
Step  
Step 2 
Step 3 l
To enter data on the PRF:
For each extension. enter 
 on Table 6 for each trunk that should have access
enabled. Enter 
 for each trunk that should not have access.
To enter data at the programming terminal:
After programming ED- Ring Control for a trunk, you see: 
ACCESS
CONTROL 
 COPY?The  option   copy the  programming from another extension.
 To copy another extension’s keys. enter Y and the extension number.
After  enter the extension number, you skip to ED-  Control programming
for  extension.
 To skip to  Control programming without making an entry, press
the space bar.
 To program the ED- Access Control options, type N. You see: LINES 1 TO
8 YYYYYYYY’
Enter an option for each trunk.Press return to:
 Skip to the next trunk without making an entry
 Go to the next trunk after making a partial entry
Press ESC to return to the Main Menu. Your changes go into effect only if 
 enter
data for a complete line (eight trunks).
 vou enter data for the last trunk, you go to ED- Call-Out Control programming
for  extension.
2-124 SOFTWARE Issue 1-O 
						

							E- EXTENSIONS
ED- TRUNK CONTROL, CALL-OUT 
Description
Note:
Related
Programming
Use this option to enable/disable   at each extension for each
trunk. If 
 in other programming, an  user can place calls on
trunks to which their extension has access.
Keep the following features in mind when programming Call-Out Control:
 Central Office Calls. PlacingUser can place calls only on trunks with  enabled.
 Prime Line SelectionFor  calls. the extension must have call-out enabled for the trunk appearing
on the 
 Line key.
 Private LineEnable call-out if the extension user should be able to place calls on the Private Line.
Enable  only for those extensions that have the Private Line.
 Tenant Extensions should have call-out enabled only for trunks in their own tenant group.
When programming Call-Out Control for DISA and tie trunk callers, refer to
ED (Trunks)- Call-Out Control.
Conditions
a. This command does not apply to a DSS Console or a Modem Pooling port.
b. To copy 
 Control data from one extension to another, use the EY
option.
Default Value
Every extension has  enabled for each trunk (Y).
Central Office Calls. Placing
E- Extensions, ES- Line Access Options, Key Access to Outbound Lines 
If enabled, user-can press a line key to place a call (if also allowed by ED
programming).
E- Extensions, ES- Line Access Options, Allow 
Line Code Dial-Up  If
enabled, user can dial a trunk code (e.g., 801) to access trunks (if also allowed
by ED programming).
E- Extensions, ES- Line Access Options, Access to Groups 90-95 (not on
key systems) 
 If enabled. user can dial 90-95 to access trunk groups 1-6.
E- Extensions, ED- Trunk Control, Access Control 
 Assign access for
each trunk on which the user should be able to place calls.
E- Trunks,  Circuit Type  Program the correct circuit type for each
trunk.
KS- Programming 
 for   Program the types of keys that allow
the extension user to place trunk calls.
Issue 1-OSOFTWARE CONFIGURATION 2-125 
						

							E- EXTENSIONS
ED- TRUNK CONTROL, CALL-OUT CONTROL
l
l
l
l
l
l
l
l
CP- Direct Trunk Access and Trunk Camp O N    
Direct Trunk Access in Class of Service
E- Extensions, 
 Class of Service  Assign Class of Service to extensions.
E- Extensions. ED- Trunk Control, Access Control 
 Assign access for
each trunk that the user should be able seize using Direct Trunk Access.
Prime Line Selection
E- Extensions, ES- Line Access Options, Key Access to Outbound Lines 
The extension must have outbound line key access to use the Prime Line key
for 
 calls.
E- 
 ED- Trunk Control,  Control  The extension must
have access for the trunk appearing en the Prime Line 
E- Extensions, EL- Prime Line   Enter the Prime  key number 
 followed by the option. The  are:
R Ringing Prime Line
I Idle Prime Line
KS- Programming Keys for 
  Program the Prime Line key as a line
key.
Private Line
E- Extensions, ES- Line Access Options, Key Access to Outbound Lines 
Enable outbound access to allow the  user to place calls on the Private
Line (if also allowed by ED programming).
E- Extensions, ED- Trunk Control, Ring Control 
 Enable/disable ringing
for the Private Line. Assign ringing only for those extensions that have the
Private Line.
E- Extensions, ED- Trunk Control, Access Control 
 Assign access for
each Private Line. Assign access only for those extensions that have the
Private Line.
E- Trunks, 
 Circuit Type  Program the correct circuit type for the
Private Lines.
KS- Programming Keys for 
  Assign the Private Line to a
programmable key. Assign the key only on those extensions that should have
the Private Line.
Tenant Service, Assigning Trunks to Tenants for Placing Calls
E- Extensions, ES- Line Access Options, Key Access to Outbound Lines 
If enabled. each user in the tenant group can press a line key to place a call (if
also allowed by ED programming).
E- Extensions, ES- Line Access Options, Allow Line Code Dial-Up 
 If
 each user in the tenant group can dial trunk access codes (e.g., 801)
to access trunks (if also allowed by ED programming).
E- Extensions, ES- Line Access Options, Access to Groups 90-95 (not on
key systems) 
 Restrict each extension in the tenant  to the trunk groups
(90-95) that the tenant should be able to dial.
E- Extensions, ED- Trunk Control, Access Control 
 Assign access only for
those trunks on which the tenant group user should be able to place calls.
Each tenant group should have access to a different set of trunks.
KS- Programming Keys for 
  Program the types of keys that allow
the extension user to place trunk calls.
2-126 SOFTWARE 
   
						

							E- EXTENSIONS
ED-  CONTROL, CALL-OUT CONTROL
Feature Reference
Instructions
Step 1 
Step 1 
Step  l
Step 3 l
Central Office Calls. Placing
Direct Trunk Access
Prime Line Selection
Private Line
Tenant Service
To enter data on the PRF:
For each extension. 
enter Y on Table 6 for each trunk that should have call-
out enabled. Enter N for each trunk that should not have call-out.
To enter data at the programming terminal:
After programming ED- Access Control for a trunk, 
you see: CALL-OUT
CONTROL 
 
The Copy option lets you  the key programming from another extension.
Press the space bar to skip to ED- Ring Control programming for the next extension.
 To  another extension’s keys. enter Y and the extension number. you enter the extension number. you skip to ED- Ring Control programmingfor the next consecutive extension.
 To skip to ED- Ring Control programming for the next extension without
making an entry, press the space bar.
 To program the ED-  Control options, type N. You see: LINES  
8 YYYYYYYY
Enter an option for each trunk.Press return to:
 Skip to the next trunk without making an entry
 Go to the next trunk after making a partial entry
Press ESC to return to the Main Menu. Your changes go into effect only if you enter
data for a complete line (eight trunks).
After 
 enter data for the last trunk, you go to ED- Ring Control programming forthe  consecutive extension.
Issue 1-OSOFI-WARE CONFIGURATION 2-127 
						

							E- EXTENSIONS
EE- RING GROUP
Description
For each member of a Ring Group, use this option to assign a Ring Group
number 
 For each member of an ONYX IV Alternate Attendant
(Attendant Console) group. enter the Alternate Attendant Group number. The
choices are:
Al Alternate Attendant Group for Attendant Console 1
A2 Alternate Attendant Group for Attendant Console 2
A3 Alternate Attendant Group for Attendant Console 3
A4 Alternate Attendant Group for Attendant Console 4
Do not assign more than 30 extensions in a CEU to the same group. If the
group must have more than 30 members, use extensions in an expansion
cabinet (if available).
Related
l
Feature Reference
Instructions
Step 1 l
Step  l
Step 2 
Step 3 l
Conditions
This option does not apply to DSS Consoles and Modem Pooling ports.
Default Value
Ring Group or Alternate Attendant group not assigned (0)
Alternate Attendant. Attendant Console (ONYX IV)
QC- Operator Programming, DSS Key 
  Enter the console’s own
extension number to enable Alternate Attendant at the Attendant Console.
Alternate Attendant, Attendant Console
Group Ring
To enter data on the PRF:
For Group Ring, enter the Ring Group number for each extension on Table 3.
For Alternate Attendant, Console (ONYX IV), enter the Alternate Attendant
group (Al-A4). To assign no group, enter 0.
To enter data at the programming terminal:
Type 
EE. You see: EXT 300
Press RETURN to program extension 
OR
Enter another extension number and press RETURN. In either case, you see:
RING GROUP
Enter data for this option from Table 3 and press RETURN.You advance to the next consecutive extension.
2-128 SOFTWARE CONFIGURATIONIssue 1-O 
						

							E- EXTENSIONS
EF- 
 THROUGH TELEPHONE SPEAKER
Description
Related
Programming
l
l
l
Feature Reference
Use this option to  Paging announcements through the telephone
speaker. When programming Tenant Service. enable this option only if tenant
members can make pages.
This option only applies to 
 and ESL sets.
Default Value
Paging through the speaker enabled (Y).
Paging. Internal and 
 Call
CP- Inhibit Access  to Page Zone  3 
  Allow/inhibit Paging to zone 
for extensions with this COS.
CP- Inhibit Access  to Page Zone  2 
  Allow/inhibit Paging to zone 2
for extensions with this COS.
CP- Inhibit Access to Page Zone 1 
  Allow/inhibit Paging to zone
1 for extensions with this COS.
CP- Inhibit Access to All Call Paging 
  Allow/inhibit All Call
Paging for extensions with this COS.
E- Extensions, 
 Class of Service  Assign Class of Service to extensions.
E- Extensions, 
 Page Zone  Assign each extension to an internal Paging
zone (01-07, or 00 for All Call only). The extension broadcasts page
announcements to the assigned zone.
Tenant Service. Assigning Internal Paging Zones to Tenants
CP- Inhibit Access  to Page Zone  3 
  Allow/inhibit Paging to  3
for extensions with this COS. You can allow this option for one tenant
group’s members and deny it for all others.
CP- Inhibit Access  to Page Zone  2 
  Allow/inhibit Paging to zone 2
for extensions with this COS. You can allow this option for one tenant
group’s members and deny it for all others.
CP- Inhibit Access to Page Zone 1 
   Paging to zone
1 for extensions with this COS. You can allow this option for one tenant
group’s members and deny it for all others.
CP- Inhibit Access to All Call Paging 
  Since all tenants hear All
Call Paging, consider using this option to prevent All Call Paging 
wide.
E- Extensions, 
 Class of Service  Assign Class of Service to extensions.
E- Extensions, 
 Page Zone  Assign each extension to an internal Paging
zone (01-07, or 00 for All Call only). Each tenant group’s extensions should
be in a different internal Paging zone.,
Paging
Tenant Service
Issue 1-O .
 CONFIGURATION 2-129 
						

							E- EXTENSIONS
   TELEPHONE 
Instructions
Step 1 
Step 1 
Step 2 l
Step 3 l
To enter data on the PRF:
For this option on   enter  for each extension that should have -Paging
through the speaker.Enter 
 if  should not have Paging through the
speaker.
To enter data at the programming terminal:
Type 
EF. You see: EXT 300 .
Press RETURN 
to program extension 300.
OR
Enter another extension number and press RETURN. In either case, you see:
PAGING THROUGH SPKR
Enter data for this option from Table 3.You advance to EF- Incoming Voice Call for this extension.
  Issue 1-O