Home > Ricoh > All in One Printer > Ricoh Mp C3000 Service Manual

Ricoh Mp C3000 Service Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Ricoh Mp C3000 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 127 Ricoh manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 1312
    Add page 621 to Favourites
    image text
    Enable zoom 
    							 
SM 5-233 B230/B237/D042 
Service 
Tables 
Enables/disables initiating a call  when the front door remains open. 
Jam Detection: Time Length 
[3 to 30 / 10 / 1 minute /step] 
011* 
Sets the time a jam must remain before it becomes an “unattended paper 
jam”. This setting is enabled only when SP5508-004 is set to 1. 
Jam Detection: Continuous 
Count  [2 to 10 / 
5 / 1 /step] 
012* 
Sets the number of consecut ive paper jams required to initiate a call. This 
setting is enabled only when SP5508-004 is set to 1. 
Door Open: Time Length  [3 to 30 / 10 / 1 /step] 
013*  Sets the length of time the door rema
ins open before the machine initiates a 
call. 
This setting is enabled only when SP5-508-004 is set to 1. 
Jam Operation: Time Length  0: Automatic  Call 
1
: Audible Warning at Machine 
021* 
Determines what happens when a paper jam is left unattended. 
Jam Operation: Continuous 
Count  0: Automatic  Call 
1
: Audible Warning at Machine 
022* 
Determines what happens when consecutive paper jams occur. 
Door Operation: Time Length  0: OFF, 1: ON 
023*  Determines what happens if the door remains open (15 min.). 
Displays a warning if set to ON. Pr
essing the call button will contact the 
service center. This setting is available  for setting only if SP5508-004 is set to 
1. 
 
[SC/Alarm Setting]   *CTL - 
5515
  With NRS (New Remote Service) in use,
 these SP codes can be set to issue 
an SC call when an SC error occurs. If th is SP is switched off, the SC call is 
not issued when an SC error occurs.
    Add page 622 to Favourites
    image text
    Enable zoom 
    							 
B230/B237/D042 5-234 SM 
001 SC Call 
002 Service Parts Near End 
Call 
003  Service Parts End Call 
004 User Call  [0 or 1 / 
1 / - ] 
0: Off 
1: On 
006 Communication Test Call
007  Machine Information 
Notice 
008 Alarm Notice 
009 Non Genuine Toner 
Alarm 
010 Supply Automatic 
Ordering Call 
011 Supply Management 
Report Call 
012  Jam/Door Open Call  [0 or 1 / 
1 / - ] 
0: Off 
1: On 
 
5516   [Individual PM Part 
Alarm Call]
  *CTL - 
001  Disable/ Enable Setting  Enables or disables t
he PM part alarm call. 
[0 or 1 /  1 / - ]   
0: Not Send, 1: Send 
002 Alarm Flag   Displays the condition of the PM part alarm call. 
[0 or 1 / 1 / - ] 
0: Ready (to send), 1: Already Send   
003  Alarm Flag Clear Clears the alarm flag (SP5-516-002). 
Do this SP after servicing for PM parts. So, 
SP5-516-002 is set to 0.
    Add page 623 to Favourites
    image text
    Enable zoom 
    							 
SM 5-235 B230/B237/D042 
Service 
Tables 
 
5610   [ACC Factory Setting]  
Recall -  - 
004 
Recalls the factory settings. 
Overwrite -  - 
005 
Overwrites the current values  onto the factory settings. 
Previous Setting -  - 
006 
Recalls the previous settings. 
 
5611   [Toner Color in 2C]  
B-C *ENG [0 to 128 / 
100 / 1 /step] 
128: Darkest density 
001 
Adjusts the Cyan correction value of  the blue signal in two-color mode. 
B-M *ENG[0 to 128 / 
100 / 1 /step] 
128: Darkest density 
002 
Adjusts the Magenta correction value of  the blue signal in two-color mode. 
G-C *ENG[0 to 128 / 
100 / 1 /step] 
128: Darkest density 
003 
Adjusts the Cyan correction value of  the blue signal in two-color mode. 
G-Y *ENG[0 to 128 / 
100 / 1 /step] 
128: Darkest density 
004 
Adjusts the Yellow correction value of the blue signal in two-color mode. 
R-M *ENG [0 to 128 / 
100 / 1 /step] 
128: Darkest density 
005 
Adjusts the Magenta correction value of  the blue signal in two-color mode. 
006 
R-Y *ENG [0 to 128 / 100 / 1 /step]
    Add page 624 to Favourites
    image text
    Enable zoom 
    							 
B230/B237/D042 5-236 SM 
128: Darkest density 
Adjusts the Yellow correction value of the blue signal in two-color mode. 
 
5618   [Color Mode Display Selection]  
- *CTL [0 or 1 / 
1 / - ] 
0: ACS, Colour, Black & White, Two Colour, 
Single colour 
1: ACD, Full Colour, Black & White   
001 
Selects the color selection display on the LCD. 
 5801   [Memory Clear] 
NOTE
: For more information, see “NOTE 1” following SP8-xxx table. 
001 All Clear 
  Resets all correction data for process 
control and all software counters, and 
returns all modes and adjustments to their default values. 
Use this SP only after replacing t he NVRAM, or after the copier has 
malfunctioned due to a damaged NVRAM. 
002 Engine  -  - 
  Clears the engine settings. 
003 SCS  -  - 
  Clears the system settings. 
IMH Memory Clr -  - 
004 
Clears IMH data. DFU  
MCS -  - 
005 
Clears MCS data.  DFU 
006 Copier Application  -  -
    Add page 625 to Favourites
    image text
    Enable zoom 
    							 
SM 5-237 B230/B237/D042 
Service 
Tables 
Clears the copy application settings. 
Fax Application  -  - 
007 
Clears the fax application settings. 
Printer Application  -  - 
008 Clears the printer application settings. 
Scanner Application  -     - 
009 
Clears the scanner application settings. 
Web Service/Network 
Application  -   - 
010 
Delete the netfile application management files and thumbnails, and 
initializes the job login ID. 
NCS -  - 
011 Initializes the system default and in
terface settings (IP address also), 
SmartDeviceMonitor for 
Admin, WebStatusMonitor settings, and the TELNET settings.   
R-FAX -  - 
012 
Initializes the job login ID, SmartDeviceMonitor for 
Admin, job history, and local storage file numbers.   
Clear DCS Settings  -  - 
014 
Initializes the DCS (Delivery Control Service) settings. 
Clear UCS Settings  -  - 
015 Initializes the UCS (User Inform ation Control Service) settings. 
MIRS Setting -  - 
016 
Initializes the MIRS (Machine Info rmation Report Service) settings. 
017 CCS -  -
    Add page 626 to Favourites
    image text
    Enable zoom 
    							 
B230/B237/D042 5-238 SM 
Initializes the CCS (Certification and Charge-control Service) settings. 
SRM Memory Clr  -  - 
018 
Initializes the SRM (System Resource Manager) settings. 
LCS -  - 
019 
Initializes the LCS (Log Count Service) settings. 
WebUapl  - 
020 
Initializes the WebUapl settings. 
 
[Free Run] 
5802  Performs a free run on the copier engine. 
 
ƒ  The machine starts free run in  the same condition as the sequence 
of A4/LT, A3 or A4 SEF printing from the 1st or 2nd tray. Therefore, 
the correct paper should be loaded in the 1st tray or 2nd tray, but 
paper is not fed. 
ƒ  The main switch has to be turned off and on after using the free run  mode for a test. 
001 TRAY1: A4LEF: FC  - 
002 TRAY2: A3: FC  - 
003 TRAY2: A4SEF: FC  -  - 
 
5803   [Input Check]  -  See Input Check in this section. 
5804
  [Output Check]  -  See Output Check in this section. 
 
 
[SC Reset] 
5810 
Resets a type A service call condition.
    Add page 627 to Favourites
    image text
    Enable zoom 
    							 
SM 5-239 B230/B237/D042 
Service 
Tables 
NOTE:  Turn the main switch off and on after resetting the SC code. 
001  Fusing SC Reset  -  - 
 
5811   [Machine Serial]  Machine Serial Number Display 
002  Display  *ENG Displays the machine serial number. 
 
5812   [Service Tel. No. Setting]  
Service *CTL  - 
001 Sets the telephone number for a servic
e representative. This number is 
printed on the Counter List, which can  be printed with the user’s “Counter” 
menu. 
This can be up to 20 characters (both  numbers and alphabetic characters can 
be input). 
Facsimile *CTL - 
002  Sets the fax or telephone number for a service representative. This number is 
printed on the Counter List. 
This can be up to 20 characters (both 
numbers and alphabetic characters can 
be input). 
Supply *CTL - 
003  Use this to input the telephone number  of your supplier for consumables. 
Enter the number and press #. 
Operation *CTL - 
004  Use this to input the telephone number  of your sales agency. Enter the 
number and press #.
    Add page 628 to Favourites
    image text
    Enable zoom 
    							 
B230/B237/D042 5-240 SM 
5816  [Remote Service]  *CTL
- 
I/F Setting 
001  Selects the remote service setting. 
[0 to 2 / 
2 / 1 /step] 
0: Remote service off 
1: CSS remote service on 
2: NRS remote service on 
CE Call 
002  Performs the CE Call at the st
art or end of the service. 
[0 or 1 /  0 / 1 /step] 
0: Start of the service 
1: End of the service 
ƒ  This SP is activated only when SP 5816-001 is set to “2”. 
Function Flag 
003  Enables or disables the remote service function. 
[0 to 1 / 
0 / 1 /step] 
0: Disabled 
1: Enabled 
Device Information Call Display Setting 
006  Displays or does not display t
he device information call content. 
[0 to 1 /  0 / 1 /step] 
0: Not displayed 
1: Displayed 
SSL Disable 
007  Uses or does not use the RCG certif
ication by SSL when calling the RCG. 
[0 to 1 /  0 / 1 /step] 
0: Uses the RCG certification 
1: Does no use the  RCG certification 
008 RCG Connect Timeout
    Add page 629 to Favourites
    image text
    Enable zoom 
    							 
SM 5-241 B230/B237/D042 
Service 
Tables 
Specifies the connect timeout  interval when calling the RCG. 
[1 to 90 /  10 / 1 second /step] 
RCG Write Timeout 
009 
Specifies the write timeout  interval when calling the RCG. 
[1 to 100 /  60 / 1 second /step] 
RCG Read Timeout 
010 
Specifies the read timeout interval when calling the RCG. 
[1 to 100 /  60 / 1 second /step] 
Port 80 Enable  - 
011  Enables/disables access via port 80 to the SOAP method. 
[0 or 1 / 
0 / – ] 
0: Disabled 
1: Enabled 
RCG – C Registed 
021  This SP displays the Cumin installation end flag. 
0: Installation not completed 
1: Installation completed 
RCG – C Registed Detail 
022 This SP displays the Cumin installation status. 
0: Basil not registered 
1: Basil registered 
2: Device registered 
Connect Type (N/M) 
023 
This SP displays and select
s the Cumin connection method. 
[0 or 1 /  0 / 1 /step 
0: Internet connection 
1: Dial-up connection 
061  Cert. Expire Timing DFU Proximity of the expiration
 of the certification.
    Add page 630 to Favourites
    image text
    Enable zoom 
    							 
B230/B237/D042 5-242 SM 
062 Use Proxy This SP setting determines 
if the proxy server is 
used when the machine communicates with the 
service center. 
Proxy Host 
063  This SP sets the address of the proxy server used for communication 
between Cumin-N and the gateway. Use this SP to set up or display the 
customer proxy server address. The 
address is necessary to set up Cumin-N. 
ƒ  The address display is limited to  128 characters. Characters beyond 
the 128 character are ignored.   
ƒ  This address is customer informat ion and is not printed in the SMC 
report. 
Proxy Port Number 
064  This SP sets the port number of t
he proxy server used for communication 
between Cumin-N and the gateway. This setting is necessary to set up 
Cumin-N. 
 
ƒ  This port number is customer info rmation and is not printed in the 
SMC report. 
Proxy User Name 
065  This SP sets the HTTP pro
xy certification user name.  
ƒ  The length of the name is limited  to 31 characters. Any character 
beyond the 31st char acter is ignored. 
ƒ  This name is customer informati on and is not printed in the SMC 
report. 
Proxy Password 
066  This SP sets the HTTP proxy certification password.  
ƒ  The length of the password is limit ed to 31 characters. Any character 
beyond the 31st char acter is ignored.
    All Ricoh manuals Comments (0)

    Related Manuals for Ricoh Mp C3000 Service Manual