Home > Ricoh > All in One Printer > Ricoh Mp C3000 Service Manual

Ricoh Mp C3000 Service Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Ricoh Mp C3000 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 127 Ricoh manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 1312
    Add page 91 to Favourites
    image text
    Enable zoom 
    							  
SM 1-59 B230/B237/D042 
Installation 
4.  Remove the four screws (  x 4 )and ten connectors ( x 10). 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Left side   
 
 
 
 
 
 
 
 
  
 
5.  Slide the PSU to the left together with its bracket, and then remove it. 
 
 
Rev. 11/2006
⇒
    Add page 92 to Favourites
    image text
    Enable zoom 
    							 
B230/B237/D042 1-60 SM 
6.  Attach the key counter I/F board to 
the rear side of the PSU bracket (4 
stud stays). 
 
 
 
   
 
7.  Connect one end of the harness to  CN3 on the  key counter I/F board , and the 
other end to  CN252 on the IOB board . 
  
 
 
 
 
 
 
 
 
 
 
8.  Remove the cutout on the rear cover  shown in the photo to the right. 
 
 
9.  Connect one end of the harness to 
CN4 on the key counter I/F board. 
 
10.  Reattach the PSU with its bracket (
  x 4 ), ( x 10). 
11.  Attach the key counter I/F board. 
12.  Reattach the PSU box cover and tighten the seven screws. 
13.  Reattach the rear cover. 
IMPORTANT : Lead the harness through the cutout space in the rear cover. 
14.  Connect the other end of the harness to the counter device. 
 
CN3  on key counter I/F CN 252  on IOB board 
Rev. 11/2006
⇒
    Add page 93 to Favourites
    image text
    Enable zoom 
    							  
SM 1-61 B230/B237/D042 
Installation 
1.18 ANTI-CONDENSATION HEATER (SCANNER) 
1.18.1 INSTALLATION PROCEDURE 
 
1.  Rear cover (see Rear Cover in the Replacement and Adjustment section) 
2.  Open the ARDF or platen cover. 
3.  Glass cover [A] (
x 4) 
4.  ARDF exposure glass [B]   
5.  Rear scale [C] (
 x 3) 
6.  Exposure glass with left 
scale [D] 
 
 
 
 
 
 
 
7.  Move the scanner carriage  to the right side by rotating 
the scanner motor [E]. 
8.  Install the heater [F] in the 
scanner unit (
  x 1, hook) 
9.  Put the connector [G] 
through the cutout. 
10.  Connect it to the connector  [H] (blue and red cords) in 
the frame of the machine. 
11.  Reassemble the machine. 
Rev. 11/2006
    Add page 94 to Favourites
    image text
    Enable zoom 
    							 
B230/B237/D042 1-62 SM 
1.19 TRAY HEATER 
1.19.1 INSTALLATION PROCEDURE 
 
1.  Remove trays 1 and 2 from the machine. 
2.  Remove the connector cover [A] (
 x 1). 
3.  Connect the connector [B] of the heater to the connector of the main machine. 
4.  Install the heater [C] inside the machine (
 x 1) 
5.  Reassemble the machine.
    Add page 95 to Favourites
    image text
    Enable zoom 
    							  
SM 1-63 B230/B237/D042 
Installation 
1.20 CONTROLLER OPTIONS 
1.20.1 OVERVIEW 
This machine has I/F card slots and SD card slots for optional I/F connections and 
applications. 
After you install an option, check that the machine can recognize it (see “Check All 
Connections” at the end of this section). 
 
I/F Card Slots 
ƒ  Slot A is used for the IEEE1394 (FireWire) or USB Host only. 
ƒ  Slot B is used for one of the optional  I/F connections (only one can be installed): 
IEEE1284, IEEE802.11 (Wireless LAN), or Bluetooth 
ƒ  Slot C is used for the file format converter only. 
 
ƒ  Only one of these cards (IEEE1284, IE EE802.11, and Bluetooth) can be installed 
at same time in this machine. 
SD Card Slots 
ƒ  Slot 1 is used for the standard printer/scanner application only.
    Add page 96 to Favourites
    image text
    Enable zoom 
    							 
B230/B237/D042 1-64 SM 
ƒ  Slot 2 is used for one of the optional applications: 
PostScript 3, Data Overwrite Secu rity Unit, PictBridge, VM Card 
ƒ  Slot 3 is used for installing the Browser Uni t, VM Card, or for service only (for example, 
updating the firmware). 
1.20.2  SD CARD APPLI MOVE 
Overview 
The service program “SD Card Appli Move” ( SP5-873) lets you copy application programs 
from one SD card to another SD card. 
Slot 1 and Slot 2 are used to store applic ation programs. But there are 3 possible 
applications (PostScript 3, DOS unit, Pict Bridge). You cannot run application programs 
from Slot 3. However you can move application pr ograms from Slot 3 to either Slot 1 or Slot 
2 with the following procedure (Slot 1 has the priority in this procedure if both Slot 1 and 
Slot 2 are used.): 
Make sure that the target SD card has enough space. 
1.  Enter SP5873 “SD Card Appli Move”.   
2.  Then move the application from the SD Ca rd in Slot 3 to the card in slot 1. 
 
ƒ  Do steps 1-2 again if you want to move another application program. 
3.  Exit the SP mode. 
Be very careful when you do the SD Card Appli Move procedure: 
ƒ  The data necessary for authentication is transferred with the application program from  an SD card to another SD card. Authentication  fails if you try to use the SD card after 
you copy the application program from one card to another card. 
ƒ  Do not use the SD card if it has been us ed before for other purposes. Normal operation 
is not guaranteed when such an SD card is used. 
 
ƒ  Remove the cover [A] (
  x 2), and then keep the SD card  in the place [B] after you 
⇒
Rev. 03/2007
    Add page 97 to Favourites
    image text
    Enable zoom 
    							  
SM 1-65 B230/B237/D042 
Installation 
copy the application program from one card to another card. This is done for the 
following reasons: 
1.  The SD card can be the only proof that  the user is licensed to use the application 
program.  
2.  You may need to check the SD card and its data to solve a problem in the future. 
ƒ  You cannot copy PostScript  application to another SD card. You have to copy the other 
application (PictBridge, DOS Unit) to the  SD card that stores the PostScript 
application. 
Move Exec 
The menu “Move Exec” (SP5-873-001) lets you c opy application programs from the original 
SD card to another SD card. 
 
ƒ  Do not turn ON the write protect switch  of the system SD card or application SD 
card on the machine. If the write protect  switch is ON, a download error (e.g. Error 
Code 44) occurs during a firmware upgrade or application merge. 
1.  Turn the main switch off. 
2.  Make sure that an SD card is in SD  Card Slot 1. The application program is 
copied into this SD card. 
3.  Insert the SD card (having stored the app lication program) in SD Card Slot 3. The 
application program is copied from this SD card. 
4.  Turn the main switch on. 
5.  Start the SP mode. 
6.  Select SP5-873-001 “Move Exec.” 
7.  Follow the messages shown on the operation panel. 
8.  Turn the main switch off. 
9.  Remove the SD card from SD Card Slot 3. 
10.  Turn the main switch on. 
11.  Check that the application programs run normally. 
Undo Exec 
“Undo Exec” (SP5-873-002) lets you copy back  application programs from an SD card to 
the original SD card. You can use this program when, for example, you have mistakenly 
copied some programs by using Move Exec (SP5-873-001). 
 
ƒ  Do not turn ON the write protect switch  of the system SD card or application SD 
card on the machine. If the write protect  switch is ON, a download error (e.g. Error 
Code 44) occurs during a firmware upgrade or application merge.
    Add page 98 to Favourites
    image text
    Enable zoom 
    							 
B230/B237/D042 1-66 SM 
1.  Turn the main switch off. 
2.  Insert the original SD card in SD Card Slot 3. The application program is copied 
back into this card. 
3.  Insert the SD card (having stored the a pplication program) to SD Card Slot 1. 
The application program is copi ed back from this SD card. 
4.  Turn the main switch on. 
5.  Start the SP mode. 
6.  Select SP5-873-002 “Undo Exec.” 
7.  Follow the messages shown on the operation panel. 
8.  Turn the main switch off. 
9.  Remove the SD card from SD Card Slot 3. 
 
ƒ  This step assumes that the application  programs in the SD card are used by 
the machine. 
10.  Turn the main switch on. 
11.  Check that the application programs run normally. 
12.  Make sure that the machine can recognize the option (see ‘Check All  Connections’ at the end of this section). 
1.20.3 POSTSCRIPT 3 
 
ƒ  Unplug the main machine power cord before you do the following 
procedure.  
 
1.  Remove the slot cover [A] from SD card slot 2 (
 x 1). 
2.  Turn the SD-card [B] label face to the rear of the machine. Then push it slowly 
into slot 2 until you hear a click.
    Add page 99 to Favourites
    image text
    Enable zoom 
    							  
SM 1-67 B230/B237/D042 
Installation 
3.  Attach the slot cover [A] ( x 1). 
 
4.  Attach the “Adobe PostScript 3” decal [C] to the front door. 
5.  Make sure that the machine can recognize the option (see ‘Check All  Connections’ at the end of this section). 
1.20.4 FILE FORMAT CONVERTER 
 
ƒ  Unplug the main machine power cord before you do the following 
procedure.  
The fax unit (B786) must be installed before inst alling this unit. This is because the mother 
board that comes with the fax unit is necessary  to connect the file format converter inside 
the machine. 
 
1.  Remove the slot cover [A] from I/F card slot C (
 x 2). 
2.  Install the file format converter [B] into I/F card slot C and then fasten it with 
screws.
    Add page 100 to Favourites
    image text
    Enable zoom 
    							 
B230/B237/D042 1-68 SM 
3.  Plug in and turn on the main power switch. 
4.  Check or set the following SP codes with the values shown below. 
 
SP No. Title Setting 
SP5-836-001  Capture Function (0:Off 1:On) 1 
SP5-836-002 Panel Setting 0 
 
5.  Check the operation.   
6.  Make sure that the machine can recognize the option (see ‘Check All 
Connections’ at the end of this section). 
1.20.5 IEEE1394 (FIREWIRE) 
Installation Procedure 
 
ƒ  Unplug the main machine power cord before you do the following 
procedure.  
You cannot install the USB host interface  at the same time as the IEEE1394 unit. 
 
1.  Remove the slot cover [A] from I/F Card Slot A (
 x 2). 
2.  Install the FireWire board [B] (Knob-screw x 2) into I/F card slot A. 
3.  Make sure that the machine can recognize the option (see ‘Check All 
Connections’ at the end of this section). 
UP Mode Settings for IEEE 1394 
Enter the UP mode. Then do the procedure below  to perform the initial interface settings for 
IEEE 1394. These settings take effect  every time the machine is powered on.
    All Ricoh manuals Comments (0)

    Related Manuals for Ricoh Mp C3000 Service Manual