Home > Ricoh > All in One Printer > Ricoh Mp C3000 Service Manual

Ricoh Mp C3000 Service Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Ricoh Mp C3000 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 127 Ricoh manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 1312
    Add page 1041 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
SM 69 B786 
B786 
Fax Option 1  Acceptable total error line ratio
0: 5% 1: 10%  If the error line ratio for a page exceeds the 
acceptable ratio, RTN will be sent to the other 
end. 
2 Treatment of pages received 
with errors during G3 
reception 
0: Deleted from memory 
without printing 
1: Printed  0: Pages received with errors are not printed. 
3 
Hang-up decision when a 
negative code (RTN or PIN) is 
received during G3 immediate 
transmission 
0: No hang-up, 1: Hang-up  0: The next page will be sent even if RTN or PIN 
is received. 
1: The machine will s
end DCN and hang up if it 
receives RTN or PIN. 
This bit is ignored for memory transmissions or if 
ECM is being used. 
4-7  Not used   Do not change the settings. 
 
Communication Switch 03 [SP No. 1-104-004]  
No  FUNCTION  COMMENTS 
0-7 Maximum number of page 
retransmissions in a G3 
memory transmission  00 - FF (Hex) times. 
This setting is not used if ECM is switched on. 
Default setting - 03(H) 
 
Communication Switch 04 - Not used  (do not change the settings) 
Communication Switch 05 - Not used (do not change the settings) 
Communication Switch 06 - Not used (do not change the settings) 
Communication Switch 07 - Not used (do not change the settings) 
Communication Switch 08 - Not used (do not change the settings) 
 
Communication Switch 09 [SP No. 1-104-010]  
No  FUNCTION  COMMENTS 
0-7  IP-Fax dial interval setting   Adjusts the interval of the I-fax dialing. 
The interval of I-fax dialing is calculated by 
following formula.  
[Interval time = specified value with this switch x 
0.2 msec] 
 
Communication Switch 0A [SP No. 1-104-011]
    Add page 1042 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
B786 70  SM 
No  FUNCTION  COMMENTS 
0 Point of resumption of 
memory transmission upon 
redialing 
0: From the error page 
1: From page 1  0: The transmission begins from the page where 
transmission failed the previous time. 
1: Transmission begins from
 the first page, using 
normal memory transmission. 
1-7  Not used   Do not change the settings. 
 
Communication Switch 0B - Not used (do not change the settings) 
Communication Switch 0C - Not used (do not change the settings) 
 Communication Switch 0D [SP No. 1-104-014] 
No   FUNCTION  COMMENTS 
0-7 The available memory 
threshold, below which ringing 
detection (and therefore 
reception into memory) is 
disabled  00 to FF (Hex), unit = 4 kbytes 
(e.g., 06(H) = 24 kbytes) 
One page is about 24 kbytes. 
The machine refers to this setting before each fax 
reception. If the amount of remaining memory is 
below this threshold, t
he machine cannot receive 
any fax messages. 
If this setting is kept at 0, the machine will detect 
ringing signals and go into receive mode even if 
there is no memory availabl e. This will result in 
communication failure. 
 
Communication Switch 0E [SP No. 1-104-015]  
No  FUNCTION  COMMENTS 
0-7 Minimum interval between 
automatic dialing attempts  06 to FF (Hex), unit = 2 s 
(e.g., 06(H) = 12 s) 
This value is the minimum time that the machine 
waits before it dials the next destination. 
 
Communication Switch 0F – Not used  (do not change the settings.) 
 
Communication Switch 10 [SP No. 1-104-017]  
No  FUNCTION  COMMENTS 
0-7 Memory transmission: 
Maximum number of dialing 
attempts to the same  01 – FE (Hex) times
    Add page 1043 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
SM 71 B786 
B786 
Fax Option 
destination 
 
Communication Switch 11 – Not used  (do not change the settings.) 
 
Communication Switch 12 [SP No. 1-104-019]  
No  FUNCTION  COMMENTS 
0-7 Memory transmission: Interval 
between dialing attempts to 
the same destination  01 – FF (Hex) minutes 
 
Communication Switch 13 – Not used  (do not change the settings.) 
 
Communication Switch 14 [SP No. 1-104-021]  
No  FUNCTION  COMMENTS 
0 Inch-to-mm conversion during 
transmission 
0: Disabled 1: Enabled  0: In immediate transmi
ssion, data scanned in 
inch format are transmitted without conversion. 
In memory transmission, data stored in the SAF 
memory in mm format are transmitted without 
conversion. 
Note: When storing the scanned data into SAF 
memory, the fax unit always converts the data into 
mm format. 
1: The machine converts the scanned data or 
stored data in the SAF memory to the format 
which was specified in the set-up protocol 
(DIS/NSF) before transmission. 
1-5  Not used   Do not change the factory settings. 
6-7 Available unit of resolution in 
which fax messages are 
received 
Bit 7: 0, Bit 6: 0 = mm 
Bit 7: 0, Bit 6: 1 = inch 
Bit 7: 1, Bit 6: 0 = mm and 
inch  (default) 
Bit 7: 1, Bit 6: 1 = 
Not used For the best performance, do not change the 
factory settings. 
The setting determined by these bits is informed 
to the transmitting terminal in the pre-message 
protocol exchange (in 
the DIS/NSF frames). 
 
Communication Switch 15 – Not used  (do not change the settings) 
 
Communication Switch 16 [SP No. 1-104-023]
    Add page 1044 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
B786 72  SM 
No  FUNCTION  COMMENTS 
0 Not used   Do not change the factory settings. 
1 Optional G3 unit (G3-2) 
0: Off 
1: On  Change this bit to 1 when installing the first 
optional G3 unit (G3-2). 
2 
Not used   Do not change the factory settings. 
3 Optional G3 unit (G3-3)  
0: Off 
1: On  Change this bit to 1 when installing the second 
optional G3 unit (G3-3). 
4-7 
Not used   Do not change the factory settings. 
 
Communication Switch 17 [SP No. 1-104-024]  
No  FUNCTION  COMMENTS 
0 SEP reception 
0: Disabled 
1: Enabled  0: Polling transmission to another maker’s 
machine using the SEP (Selective Polling) signal 
is disabled. 
1 
SUB reception 
0: Disabled 
1: Enabled   0: Confidential reception to another maker’s 
machine using the SUB (Sub-address) signal is 
disabled. 
2 
PWD reception 
0: Disabled 
1: Enabled  0: Disables features that
 require PWD (Password) 
signal reception. 
3-6  Not used   Do not change the factory settings. 
7 Action when there is no box 
with an F-code that matches 
the received SUB code 
0: Disconnect the line 
1: Receive the message 
(using normal reception 
mode)  Change this setting when the customer requires. 
 
Communication Switch 18 [SP No. 1-104-025]  
No  FUNCTION  COMMENTS 
0-4 Not used   Do not change the factory settings. 
5 IP-Fax dial-in routing selection
0: Off 
1: On  1: Transfers receiving data to each IP-Fax dial-in 
number.  
IP-Fax dial-in number is 4 digit-number. 
6-7 
Not used   Do not change the factory settings.
    Add page 1045 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
SM 73 B786 
B786 
Fax Option 
 
Communication Switch 19 - Not used  (do not change the settings) 
Communication Switch 1A - Not used  (do not change the settings) 
 
Communication Switch 1B [SP No. 1-104-028] 
No   FUNCTION  COMMENTS 
0-7 Extension access code (0 to 
7) to turn V.8 protocol On/Off  
0: On 
1: Off 
   If the PABX does not support V.8/V.34 protocol 
procedure, set this bit to “1” to disable V.8. 
Example: If “0” is the PSTN access code, set bit 0 
to 1. When the machine detects “0” as the first 
dialed number, it automat
ically disables V.8 
protocol. (Alternatively, if  “3” is the PSTN access 
code, set bit 3 to 1.)  
 
Communication Switch 1C [SP No. 1-104-029] 
No   FUNCTION  COMMENTS 
0-1 Extension access code (8 and 
9) to turn V.8 protocol On/Off   
0: On 
1: Off  Refer to communication switch 1B. 
Example: If “8” is the PSTN access code, set bit 0 
to 1. When the machine detects “8” as the first 
dialed number, it automat
ically disables V.8 
protocol. (If “9” is the PSTN access code, use bit 
1.) 
2-7  Not used   Do not change the settings. 
 
Communication Switch 1D - Not used (do not change the settings) 
Communication Switch 1E - Not used  (do not change the settings) 
Communication Switch 1F - Not used (do not change the settings) 
 
4.3.5 G3 SWITCHES 
G3 Switch 00 [SP No. 1-105-001] 
No  FUNCTION  COMMENTS 
0 
1 Monitor speaker during 
communication (tx and rx) 
Bit 1: 0, Bit 0: 0 = Disabled 
Bit 1: 0, Bit 0: 1 = Up to Phase 
B 
Bit 1: 1, Bit 0: 0 = All the time 
Bit 1: 1, Bit 0: 1 =
 Not used (0, 0): The monitor speaker is disabled all through 
the communication. 
(0, 1): The monitor speaker is on up to phase B in 
the T.30 protocol. 
(1, 0): Used for testing. The monitor speaker is on 
all through the communication. Make sure that 
you reset these bits after testing.
    Add page 1046 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
B786 74  SM 
2 Monitor speaker during 
memory transmission 
0: Disabled 1: Enabled  1: The monitor speaker 
is enabled during memory 
transmission. 
3-5  Not used   Do not change the settings. 
6 G3 mode selection for direct 
line 
0: Off 
1:On   1: G3 communication through the direct line is 
enabled.  
7 
Not used   Do not change the settings. 
 
G3 Switch 01 [SP No. 1-105-002]  
No  FUNCTION  COMMENTS 
0-1 Not used   Do not change the settings. 
2-3 Not used   Do not change the settings. 
4 DIS frame length 
0: 10 bytes 1: 4 bytes  1: The bytes in the DIS frame after the 4th byte 
will not be transmitted (set to 1 if there are 
communication problems with PC-based faxes 
which cannot receive the 
extended DIS frames). 
5 Not used   Do not change the setting. 
6 Forbid CED/AMsam output 
0: Off 
1: On (Forbid output)  Do not change this setting (Default: 0: Off), unless 
communication problem is caused by a CED or 
ANSam transmission. 
7 
Not used   Do not change the setting. 
 
G3 Switch 02 [SP No. 1-105-003]  
No  FUNCTION  COMMENTS 
0 G3 protocol mode used 
0: Standard and non-standard 
1: Standard only  Change this bit to 1 only when the other end can 
only communicate with machines that send T.30-
standard frames only. 
1: Disables NSF/NSS si
gnals (these are used in 
non-standard mode communication) 
1-6  Not used   Do not change the settings. 
7 Short preamble 
0: Disabled 1: Enabled  Refer to Appendix B in the Group 3 Facsimile 
Manual for details about Short Preamble. 
 
G3 Switch 03 [SP No. 1-105-004]  
No  FUNCTION  COMMENTS
    Add page 1047 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
SM 75 B786 
B786 
Fax Option 0  DIS detection number  
(Echo countermeasure) 
0: 1  
1: 2  0: The machine will hang up if it receives the 
same DIS frame twice. 
1: Before sending DCS, the machine will wait for 
the second DIS which is caused by echo on the 
line. 
1 
Not Used   Do not change the settings. 
2 V.8 protocol 
0: Disabled 
1: Enabled  0: V.8/V.34 communications will not be possible. 
Note: 
Do not set to 0 unless the line condition is always 
bad enough to slow down the data rate to 14.4 
kbps or lower. 
3 
ECM frame size 
0: 256 bytes 
1: 64 bytes  Keep this bit at “0” in most cases. 
4 CTC transmission conditions 
0: After one PPR signal 
received 
1: After four PPR signals 
received (ITU-T standard)  0: When using ECM in non-standard (NSF/NSS) 
mode, the machine sends a CTC to drop back the 
modem rate after receiving a PPR, if the following 
condition is met in communi
cations at 14.4, 12.0, 
9.6, and 7.2 kbps.  
NTransmit- Number of transmitted frames 
NResend- Number of frames to be retransmitted 
1: When using ECM, the  machine sends a CTC to 
drop back the modem rate after receiving four 
PPRs. 
PPR, CTC: These are ECM protocol signals. 
This bit is not effective in V.34 communications. 
5  Modem rate used for the next 
page after receiving a 
negative code (RTN or PIN) 
0: No change 1: Fallback  1: The machine’s tx m
odem rate will fall back 
before sending the next page  if a negative code is 
received. This bit is i gnored if ECM is being used. 
6 Not Used   Do not change the settings 
7 Select detection of reverse 
polarity in ringing 
0: Off  
1: On  This switch is used to prevent reverse polarity in 
ringing on the phone line (applied to PSTN-G3 
ringing). Do not change this setting 
0: No detection 
 Outside Japan 
1: Detection 
 Inside Japan only 
 
 
G3 Switch 04 [SP No. 1-105-005]  
No  FUNCTION  COMMENTS 
0-3 Training error detection 
threshold  0 - F (Hex); 0 - 15 bits 
If the number of error bits in the received TCF is 
below this threshold, the machine informs the
    Add page 1048 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
B786 76  SM 
sender that training has succeeded. 
4-7 Not used   Do not change the settings. 
 
G3 Switch 05 [SP No. 1-105-006]  
No  FUNCTION  COMMENTS 
Initial Tx modem rate 
Bit 3  Bit 2  Bit 1  Bit 0  bps 
0 0 0 1 2.4k 
0 0 1 0 4.8k 
0 0 1 1 7.2k 
0 1 0 0 9.6k 
0 1 0 1 12.0k 
0 1 1 0 14.4k 
0 1 1 1 16.8k 
1 0 0 0 19.2k 
1 0 0 1 21.6k 
1 0 1 0 24.0k 
1 0 1 1 26.4k 
1 1 0 0 28.8k 
1 1 0 1 31.2k 
1 1 1 0 33.6k 
0-3 
Other settings -  Not used These bits set the initial starting modem rate for 
transmission. 
Use the dedicated transmission parameters if 
you need to change this for specific receivers. 
If a modem rate 14.4 kbps or slower is selected, 
V.8 protocol should 
be disabled manually. 
Cross reference 
V.8 protocol on/off - G3 switch 03, bit2 
4-5  Initial modem type for 9.6 k or 
7.2 kbps. 
Bit 5: 0, Bit 4: 0 = V.29 
Bit 5: 0, Bit 4: 1 = V.17 
Bit 5: 1, Bit 4: 0 = V.34 
Bit 5: 1, Bit 4: 1 =
 Not used  These bits set the initial modem type for 9.6 and 
7.2 kbps, if the initial modem rate is set at these 
speeds. 
6-7 
Not used   Do not change the settings.
    Add page 1049 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
SM 77 B786 
B786 
Fax Option 
 
G3 Switch 06 [SP No. 1-105-007]  
No  FUNCTION  COMMENTS 
Initial Rx modem rate 
Bit 3  Bit 2  Bit 1  Bit 0  bps 
0 0 0 1  2.4k 
0 0 1 0  4.8k 
0 0 1 1  7.2k 
0 1 0 0  9.6k 
0 1 0 1  12.0k 
0 1 1 0  14.4k 
0 1 1 1  16.8k 
1 0 0 0  19.2k 
1 0 0 1  21.6k 
1 0 1 0  24.0k 
1 0 1 1  26.4k 
1 1 0 0  28.8k 
1 1 0 1  31.2k 
1 1 1 0  33.6k 
0-3 
Other settings -  Not used  ƒ  These bits set the initial starting modem 
rate for reception. 
ƒ  Use a lower setting if high speeds pose 
problems during reception. 
ƒ  If a modem rate 14.4 kbps or slower is  selected, V.8 protocol should be 
disabled manually. 
Cross reference: 
V.8 protocol on/off - G3 switch 03, bit2 
Modem types available for reception 
Bit 7  Bit 6  Bit 5  Bit 4  Setting 
0 0 0 1  V.27ter 
0 0 1 0 V.27ter,V.29
0 0 1 1  V.27ter, 
V.29, V.33 
0 1 0 0  V.27ter, 
V.29, 
V.17/V.33 
4-7 
0 1 0 1  V.27ter, 
V.29, 
V.17/V33, 
V.34 ƒ  The setting of these bits is used to 
inform the transmitting terminal of the 
available modem type for the machine 
in receive mode. 
ƒ  If V.34 is not selected, V.8 protocol must  be disabled manually. 
Cross reference: 
V.8 protocol on/off - G3 switch 03, bit2
    Add page 1050 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
B786 78  SM 
Other settings - Not used 
 
G3 Switch 07 [SP No. 1-105-008]  
No  FUNCTION   COMMENTS 
0-1 PSTN cable equalizer 
(tx mode: Internal) 
Bit 1: 0, Bit 0: 0 = None 
Bit 1: 0, Bit 0: 1 = Low 
Bit 1: 1, Bit 0: 0 = Medium 
Bit 1: 1, Bit 0: 1 =
 High  Use a higher setting if there is signal loss at higher 
frequencies because of the length of wire between 
the modem and the telephone exchange. 
Use the dedicated transmission parameters for 
specific receivers. 
Also, try using the cable equalizer if one or more 
of the following symptoms occurs. 
Communication error 
Modem rate fallback occurs frequently. 
 
ƒ  This setting is not effective in V.34 
communications. 
2-3  PSTN cable equalizer 
(rx mode: Internal) 
Bit 3: 0, Bit 2: 0 = None 
Bit 3: 0, Bit 2: 1 = Low 
Bit 3: 1, Bit 2: 0 = Medium 
Bit 3: 1, Bit 2: 1 =
 High  Use a higher setting if there is signal loss at higher 
frequencies because of the length of wire between 
the modem and the telephone exchange. 
Also, try using the cable equalizer if one or more 
of the following symptoms occurs. 
Communication error with error codes such as  
 0-20, 0-23, etc. 
Modem rate fallback occurs frequently. 
 
ƒ  This setting is not effective in V.34 
communications. 
4  PSTN cable equalizer 
(V.8/V.17 rx mode: External) 
0: Disabled 
1: Enabled  Keep this bit at “1”. 
5 
Not used   Do not change the settings. 
6 Parameter selection for dial 
tone detection 
0: Normal parameter 
1: Specific parameter  0: This uses the fixed table in the ROM for dial 
tone detection. 
1: This uses t
he specific parameter adjusted with 
SRAM (69ECBEH - 69ECDEH). Select this if the 
dial tone cannot be detec ted when the Normal 
parameter: 0 is selected. 
7  Not used   Do not change the settings. 
 
 
G3 Switch 08 - Not used  (do not change the settings) 
 
G3 Switch 09 - Not used (do not change the settings)
    All Ricoh manuals Comments (0)

    Related Manuals for Ricoh Mp C3000 Service Manual