Home > Ricoh > All in One Printer > Ricoh Mp C3000 Service Manual

Ricoh Mp C3000 Service Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Ricoh Mp C3000 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 127 Ricoh manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 1312
    Add page 1051 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
SM 79 B786 
B786 
Fax Option 
 
G3 Switch 0A [SP No. 1-105-011]  
No  FUNCTION  COMMENTS 
0-1 Maximum allowable carrier 
drop during image data 
reception 
Bit 1: 0, Bit 0: 0 = 200 (ms) 
Bit 1: 0, Bit 0: 1 = 400 (ms) 
Bit 1: 1, Bit 0: 0 = 800 (ms) 
Bit 1: 1, Bit 0: 1 =
 Not used These bits set the acceptable modem carrier drop 
time. 
Try using a longer setting if error code 0-22 is 
frequent. 
2 
Select cancellation of high-
speed RX if carrier signal 
lost while receiving 
0: Off 
1: On  This switch setting determines if high-speed 
receiving ends if the carrier signal is lost when 
receiving during non-ECM mode 
3 
Not used   Do not change the settings 
4 Maximum allowable frame 
interval during image data 
reception. 
0: 5 s 1: 13 s  This bit set the maximum interval between EOL 
(end-of-line) signals and the maximum interval 
between ECM frames from the other end. 
Try using a longer setting if error code 0-21 is 
frequent. 
5 
Not used   Do not change the settings. 
6 Reconstruction time for the 
first line in receive mode 
0: 6 s 1: 12 s  When the sending terminal
 is controlled by a 
computer, there may be a delay in receiving page 
data after the local machine accepts set-up data 
and sends CFR. This  is outside the T.30 
recommendation. But, if this  delay occurs, set this 
bit to 1 to give the sending machine more time to 
send data. 
Refer to error code 0-20. 
ITU-T T.30 recommendation:  The first line should 
come within 5 s of CFR. 
7  Not used   Do not change the settings. 
 
G3 Switch 0B - Not used  (do not change the settings). 
G3 Switch 0C - Not used (do not change the settings) 
G3 Switch 0D - Not used (do not change the settings). 
 
G3 Switch 0E [SP No 1-105-015]  
0-7 
Set CNG send time interval 
Some machines on the receiving side may not  be able to automatically switch the
    Add page 1052 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
B786 80  SM 
3-second CNG interval.  
High order bit 3000-2250ms: 3000-50xNms 
3000 – 50 x Nms 0F (3000 ms) ≤
 N ≤ FF (2250 
ms) 
Low order bit  00-0E(3000-3700ms: 3000+50xNms 
3000 – 50 x Nms 0F (3000 ms) ≤
 N ≤ 0F (3700 
ms) 
 
G3 Switch 0F [SP No. 1-105-016]  
No  FUNCTION  COMMENTS 
0 Alarm when an error occurred 
in Phase C or later 
0: Disabled 
1: Enabled  If the customer wants to hear an alarm after each 
error communication, change this bit to “1”. 
1 Alarm when the handset is off-
hook at the end of 
communication 
0: Disabled 
1: Enabled  If the customer wants to hear an alarm if the 
handset is off-hook at the end of fax 
communication, change this bit to “1”. 
2 
Not used   Do not change the settings. 
4 Sidaa manual calibration 
setting 
0: Off 
1: On   1: manually calibrates for communication with a 
line, whose current change occurs such as an 
optical fiber line. 
5-7 
Not used   Do not change the settings. 
 
4.3.6 G3-2/3 SWITCHES 
These switches require an optional G3 interface unit. 
G3-3 switches are the same as for G3-2 switches. 
G3-2 Switch 00 [SP No. 1-106-001]  
No  FUNCTION  COMMENTS 
0-1 Monitor speaker during 
communication (tx and rx) 
Bit 1: 0, Bit 0: 0 = Disabled 
Bit 1: 0, Bit 0: 1 = Up to Phase 
B 
Bit 1: 1, Bit 0: 0 = All the time 
Bit 1: 1, Bit 0: 1 = Not used  (0, 0): The monitor speaker is disabled all through 
the communication. 
(0, 1): The monitor speaker is on up to phase B in 
the T.30 protocol. 
(1, 0): Used for testing. The monitor speaker is on 
all through the communication. Make sure that 
you reset these bits after testing. 
2  Monitor speaker during  1: The monitor speaker is enabled during memory
    Add page 1053 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
SM 81 B786 
B786 
Fax Option 
memory transmission 
0: Disabled 1: Enabled  transmission. 
3-6 
Not used   Do not change the settings. 
 
G3-2 Switch 01 [SP No. 1-106-002]  
No  FUNCTION  COMMENTS 
0-3 Not used   Do not change the settings. 
4 DIS frame length 
0: 10 bytes, 1: 4 bytes  1: The bytes in the DIS frame after the 4th byte 
will not be transmitted (set to 1 if there are 
communication problems with PC-based faxes 
which cannot receive the 
extended DIS frames). 
5 Not used   Do not change the setting. 
6 CED/ANSam transmission 
0: Disabled 
1: Enabled  Do not change this setting, unless the 
communication problem is caused by the 
CED/ANSam transmission. 
7 
Not used   Do not change the setting. 
 
G3-2 Switch 02 [SP No. 1-106-003]  
No  FUNCTION  COMMENTS 
0 G3 protocol mode used 
0: Standard and non-standard 
1: Standard only  Change this bit to 1 only when the other end can 
only communicate with machines that send T.30-
standard frames only. 
1: Disables NSF/NSS si
gnals (these are used in 
non-standard mode communication) 
1-4  Not used   Do not change the settings. 
5 Use of modem rate history for 
transmission using 
Quick/Speed Dials 
0: Disabled 
1: Enabled  0: Communications using Quick/Speed Dials 
always start from the highest modem rate. 
1: The machine refers to the modem rate history 
for communications with the same machine when 
determining the most suitable rate for the current 
communication. 
6 
Not used   Do not change the settings. 
7 Short preamble 
0: Disabled, 1: Enabled  Refer to Appendix B in the Group 3 Facsimile 
Manual for details about Short Preamble. 
 
G3-2 Switch 03 [SP No. 1-106-004]  
No  FUNCTION  COMMENTS
    Add page 1054 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
B786 82  SM 
0 DIS detection number  
(Echo countermeasure) 
0: 1 
1: 2  0: The machine will hang up if it receives the 
same DIS frame twice. 
1: Before sending DCS, the machine will wait for 
the second DIS which is caused by echo on the 
line. 
1 
Not used   Do not change the settings. 
2 V.8 protocol 
0: Disabled 
1: Enabled  0: V.8/V.34 communications will not be possible.  
ƒ  Do not set to 0 unless the line condition is 
always bad enough to slow down the 
data rate to 14.4 kbps or lower. 
3  ECM frame size 
0: 256 bytes 
1: 64 bytes  Keep this bit at “0” in most cases. 
4 CTC transmission conditions 
0: After one PPR signal 
received 
1: After four PPR signals 
received (ITU-T standard)  0: When using ECM in non-standard (NSF/NSS) 
mode, the machine sends a CTC to drop back the 
modem rate after receiving a PPR, if the following 
condition is met in communi
cations at 14.4, 12.0, 
9.6, and 7.2 kbps. 
 
NTransmit- Number of transmitted frames 
NResend- Number of frames to be retransmitted 
 
1: When using ECM, the  machine sends a CTC to 
drop back the modem rate after receiving four 
PPRs. 
 
PPR, CTC: These are ECM protocol signals. 
This bit is not effective in V.34 communications. 
5  Modem rate used for the next 
page after receiving a 
negative code (RTN or PIN) 
0: No change, 1: Fallback  1: The machine’s tx m
odem rate will fall back 
before sending the next page  if a negative code is 
received. This bit is i gnored if ECM is being used. 
6 Not used   Do not change the settings. 
7 Not used   Do not change the settings. 
 
G3-2 Switch 04 [SP No. 1-106-005]  
No  FUNCTION  COMMENTS 
0-3 Training error detection 
threshold  0 - F (Hex); 0 - 15 bits 
If the number of error bits in the received TCF is 
below this threshold, the machine informs the 
sender that training has succeeded. 
4-7 
Not used   Do not change the settings.
    Add page 1055 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
SM 83 B786 
B786 
Fax Option 
 
G3-2 Switch 05 [SP No. 1-106-006]  
No  FUNCTION  COMMENTS 
Initial Tx modem rate 
Bit 3  Bit 2  Bit 1  Bit 0  bps 
0 0 0 1 2.4k 
0 0 1 0 4.8k 
0 0 1 1 7.2k 
0 1 0 0 9.6k 
0 1 0 1 12.0k 
0 1 1 0 14.4k 
0 1 1 1 16.8k 
1 0 0 0 19.2k 
1 0 0 1 21.6k 
1 0 1 0 24.0k 
1 0 1 1 26.4k 
1 1 0 0 28.8k 
1 1 0 1 31.2k 
1 1 1 0 33.6k 
0-3 
Other settings -  Not used These bits set the initial starting modem rate for 
transmission. 
Use the dedicated transmission parameters if 
you need to change this for specific receivers. 
If a modem rate 14.4 kbps or slower is selected, 
V.8 protocol should 
be disabled manually. 
Cross reference  
V.8 protocol on/off - G3 switch 03, bit2 
4-5  Initial modem type for 9.6 k or 
7.2 kbps. 
Bit 5: 0, Bit 4: 0 = V.29 
Bit 5: 0, Bit 4: 1 = V.17 
Bit 5: 1, Bit 4: 0 = V.34 
Bit 5: 1, Bit 4: 1 =
 Not used  These bits set the initial modem type for 9.6 and 
7.2 kbps, if the initial modem rate is set at these 
speeds. 
6-7 
Not used   Do not change the settings.
    Add page 1056 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
B786 84  SM 
G3-2 Switch 06 [SP No. 1-106-007] 
No  FUNCTION  COMMENTS 
Initial Rx modem rate 
Bit 3  Bit 2  Bit 1  Bit 0  bps 
0 0 0 1  2.4k 
0 0 1 0  4.8k 
0 0 1 1  7.2k 
0 1 0 0  9.6k 
0 1 0 1  12.0k 
0 1 1 0  14.4k 
0 1 1 1  16.8k 
1 0 0 0  19.2k 
1 0 0 1  21.6k 
1 0 1 0  24.0k 
1 0 1 1  26.4k 
1 1 0 0  28.8k 
1 1 0 1  31.2k 
1 1 1 0  33.6k 
0-3 
Other settings -  Not used  ƒ  These bits set the initial starting modem 
rate for reception. 
ƒ  Use a lower setting if high speeds pose 
problems during reception. 
ƒ  If a modem rate 14.4 kbps or slower is  selected, V.8 protocol should be 
disabled manually. 
Cross reference : 
V.8 protocol on/off - G3 switch 03, bit2 
Modem types available for reception 
Bit 7  Bit 6  Bit 5  Bit 4  Setting 
0 0 0 1  V.27ter 
0 0 1 0 V.27ter,V.29
0 0 1 1  V.27ter, 
V.29, V.33 
0 1 0 0  V.27ter, 
V.29, 
V.17/V.33 
0 1 0 1  V.27ter, 
V.29, 
V.17/V33, 
V.34 
4-7 
Other settings -  Not used  ƒ  The setting of these bits is used to 
inform the transmitting terminal of the 
available modem type for the machine 
in receive mode. 
ƒ  If V.34 is not selected, V.8 protocol must  be disabled manually. 
Cross reference: 
V.8 protocol on/off - G3 switch 03, bit2
    Add page 1057 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
SM 85 B786 
B786 
Fax Option 
 
G3-2 Switch 07 [SP No. 1-106-008]  
No  FUNCTION   COMMENTS 
0-1 PSTN cable equalizer 
(tx mode: Internal) 
Bit 1: 0, Bit 0: 0 = None 
Bit 1: 0, Bit 0: 1 = Low 
Bit 1: 1, Bit 0: 0 = Medium 
Bit 1: 1, Bit 0: 1 =
 High  Use a higher setting if there is signal loss at higher 
frequencies because of the length of wire between 
the modem and the telephone exchange. 
Use the dedicated transmission parameters for 
specific receivers. 
Also, try using the cable equalizer if one or more 
of the following symptoms occurs. 
Communication error 
Modem rate fallback occurs frequently. 
 
ƒ  This setting is not effective in V.34 
communications. 
2-3  PSTN cable equalizer 
(rx mode: Internal) 
Bit 3: 0, Bit 2: 0 = None 
Bit 3: 0, Bit 2: 1 = Low 
Bit 3: 1, Bit 2: 0 = Medium 
Bit 3: 1, Bit 2: 1 =
 High  Use a higher setting if there is signal loss at higher 
frequencies because of the length of wire between 
the modem and the telephone exchange. 
Also, try using the cable equalizer if one or more 
of the following symptoms occurs. 
Communication error with error codes such as  
 0-20, 0-23, etc. 
Modem rate fallback occurs frequently. 
 
ƒ  This setting is not effective in V.34 
communications. 
4  PSTN cable equalizer 
(V.8/V.17 rx mode: External) 
0: Disabled 
1: Enabled  Keep this bit at “1”. 
5 
Not used   Do not change the settings. 
6 Parameter selection for dial 
tone detection 
0: Normal parameter 
1: Specific parameter  0: This uses the fixed table in the ROM for dial 
tone detection. 
1: This uses t
he specific parameter adjusted with 
SRAM (69ECBEH - 69ECDEH). Select this if the 
dial tone cannot be detec ted when the Normal 
parameter: 0 is selected. 
7  Not used   Do not change the settings. 
 
G3-2 Switch 08 - Not used  (do not change the settings) 
G3-2 Switch 09 - Not used (do not change the settings)
    Add page 1058 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
B786 86  SM 
G3-2 Switch 0A [SP No. 1-106-011] 
No  FUNCTION  COMMENTS 
0-1 Maximum allowable carrier 
drop during image data 
reception 
Bit 1: 0, Bit 0: 0 = 200 (ms) 
Bit 1: 0, Bit 0: 1 = 400 (ms) 
Bit 1: 1, Bit 0: 0 = 800 (ms) 
Bit 1: 1, Bit 0: 1 =
 Not used These bits set the acceptable modem carrier drop 
time. 
Try using a longer setting if error code 0-22 is 
frequent. 
2 
Select cancellation of high-
speed RX if carrier signal 
lost while receiving 
0: Off 
1: On  This switch setting determines if high-speed 
receiving ends if the carrier signal is lost when 
receiving during non-ECM mode 
3 
Not used   Do not change the settings 
4 Maximum allowable frame 
interval during image data 
reception. 
0: 5 s 1: 13 s  This bit set the maximum interval between EOL 
(end-of-line) signals and the maximum interval 
between ECM frames from the other end. 
Try using a longer setting if error code 0-21 is 
frequent. 
5 
Not used   Do not change the settings. 
6 Reconstruction time for the 
first line in receive mode 
0: 6 s 1: 12 s  When the sending terminal
 is controlled by a 
computer, there may be a delay in receiving page 
data after the local machine accepts set-up data 
and sends CFR. This  is outside the T.30 
recommendation. But, if this  delay occurs, set this 
bit to 1 to give the sending machine more time to 
send data. 
Refer to error code 0-20. 
ITU-T T.30 recommendation:  The first line should 
come within 5 s of CFR. 
7  Not used   Do not change the settings. 
 
G3-2 Switch 0B - Not used  (do not change the settings.) 
G3-2 Switch 0C - Not used (do not change the settings.) 
G3-2 Switch 0D - Not used (do not change the settings) 
G3-2 Switch 0E - Not used (do not change the settings) 
G3-2 Switch 0F - Not used (do not change the settings)
    Add page 1059 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
SM 87 B786 
B786 
Fax Option 
4.3.7  IP FAX SWITCHES 
IP Fax Switch 00 [SP No. 1-111-001]  
No.  FUNCTION  COMMENTS 
0 Not used   Do not change this setting. 
1 IP Fax Transport 
0: TCP, 1: UDP  Selects TCP or UDP protocol for IP-Fax 
2 
IP Fax single port selection 
0: OFF, 1: ON (enable)  Selects single data port. 
3 IP Fax double ports (single data 
port) selection 
0: OFF, 1: ON (enable)  Selects whether IP-Fax uses a double port. 
4 
IP Fax Gatekeeper  
0: OFF, 1: ON (enable)  Enables/disables the 
communication via the 
gatekeeper for IP-Fax. 
5  IP Fax T30 bit signal reverse 
0: LSB first, 1: MSB first  Reverses the T30 bit signal. 
6 
IP Fax max bit rate setting 
0: Not affected, 1: Affected  When 0 is selected, the max bit rate does 
not affect the value of the DIS/DCS. 
When 1 is selected, the max bit rate affects 
the value of the DIS/DCS. 
7 
IP Fax received telephone number 
confirmation 
0: No confirmation, 1: 
Confirmation  When 0 is selected, fax data is received 
without checking the telephone number. 
When 1 is selected, fax data is received 
only when confirming 
that the telephone 
number from the sender matches the 
registered telephone number in this 
machine. If this confir mation fails, the line is 
disconnected. 
 
IP-Fax Switch 01 
No.   FUNCTION  COMMENTS 
Select IP FAX Delay Level 
Bit3 Bit2 Bit1 Bit0  Setting 
0 0 0 0 Level 0 
0 0 0 1 Level 1 
0 0 1 0 Level 2 
0 0 1 1 Level 3 
0-3 
      Raise the level by selecting a higher setting 
if too many transmission errors are 
occurring on the network. 
If TCP/UDP is enabled on the network, raise 
this setting on the T.30 machine. Increasing 
the delay time allows the recovery of more 
lost packets. 
If only UDP is enabled, increase the number 
of redundant packets. 
Level 1~2: 3 Redundant packets 
Level 3: 4 Redundant packets
    Add page 1060 to Favourites
    image text
    Enable zoom 
    							Bit Switches 
B786 88  SM 
4-7  IP Fax preamble wait time setting Selects the preamble wait time. 
[00 to 0f]  
There are 16 values in this 4-bit binary 
switch combination.  
Waiting time: set value level x 100 ms 
Max: 0f (1500 ms) Min: 00 (No wait time) 
The default is 0000 (00H). 
 
IP Fax Switch 02 [SP No. 1-111-003]  
No.  FUNCTION  COMMENTS 
0 IP Fax bit signal reverse setting 
0: Maker code setting 
1: Internal bit switch setting   When 0 is selected, the bit signal reverse 
method is decided by the maker code. 
When 1 is selected, the bit signal reverse 
method is decided by the internal bit switch. 
When communicating between IP Fax 
devices, LSB firs
t is selected.) 
1 IP Fax transmission speed setting 
0: Modem speed 
1: No limitation  Selects the transmit speed for IP Fax 
communication. 
2 
SIP transport setting  
0: TCP 
1: UDP  This bit switch sets the transport that has 
priority for receiving IP Fax data. 
This function is activated only when the 
sender has both TCP and UDP.  
3 
CCM connection 
0: No CCM connection 
1: CCM connection  When 1 is selected, only the connection 
call message with H.323 or no tunneled 
H.245 is transmitted via CCM. 
4 
Message reception selection from 
non-registered SIP server  
0: Answer 
1: Not answer  0: This answers the INVITE message from 
the SIP server not registered for the 
machine. 
1: This does not receive the INVITE 
message from the SIP server not registered 
for the machine and send a refusal 
message.  
5 
ECM communication setting 
0: No limit for image compression 
1: Limit for image compression  0: This does not limit
 the type of the image 
compression with ECM communication. 
1: When the other end machine is Ciscco, 
this permits the image compression other 
than JBIG or MMR with ECM 
communication.  
6-7  Not used   Do not change these settings.
    All Ricoh manuals Comments (0)

    Related Manuals for Ricoh Mp C3000 Service Manual