Panasonic Dbs 824 Instructions Manual
Have a look at the manual Panasonic Dbs 824 Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Hunt Group Name AssignmentFF6Hunt Group Name Assignment Software VersionCPC-S and CPC-M, Version 1 0 and higher Address- FF6 W (HuntGrp)# CONF (NNNNNNNNNNN)# DescriptionHunt groups can be given names of up to 10 characters to help identify the source of trunk calls transferred from the hunt group Hunt group names can only be assigned through the programming mode using a DSS/72See Figure 6-l on page 6-3 for DSS/72 keys used for text assignment Programming To assign hunt group namesFF6 6## (l-4)# CONF (NNNNNNNNNN)# tfHunt Group Number CPC-S and CPC-M l-4Hunt Group Text (up to 10 characters) To clear hunt group names6-10 DBS 824-l O-400Issued 3/i /95
FF6Call Waiting/OHVA Text Reply Call Waiting/OHVA Text Reply Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF6 7# (l-5)# CONF (NNNNNNNNNNNNNNN)# DescriptionWhen a busy party receives an indication of an incoming intercom call the busy party can respond by sending a text message back to the caller The text message can be sent after a Call Waiting tone an Offhook Voice Announce, or a Call Waiting tone followed by Offhook Voice Announce This address allows you to change the default messages The following table shows the default messages Table 6-2Default call waitinglOHVA text reply messages I 2I PIease HoldI 3Will Call Back 4Transfer 1 5 1 Unavailable Changing these default text messages in the programming mode requires a DSS/72 consoleFigure 6- 1 on page 6-3 shows the DSS/72 keys used for textassignment Call WaitingjOHVA text messages can also be changed through the attendant phone without entering the programming mode For instructions on this method of text assignment, see Section 700-Feature Operation Programming To assign call waiting/OHVA text reply messages FF6 7# (115)# CONF (NNNNNNNNNNNNNNN)# ftMessage Number l-5 Message Text (up to 15 characters) issued 3/l 195DBS 824-l O-4006-11
Call Waiting/OHVA Text ReplyFF6 To clear call waiting/OHVA text reply messagesFF6 7# (l+)#CONF ON/OFF G-12DBS 824- 1 O-400Issued 3/l /95
7. Toll Restrictions (FF7)Use the FF7 program addresses in this chapter to perform Toll Restriction Service (TRS) programming This chapter covers the following topics TopicPage An Overview of Toll Restrictions 7-3International Calling For TRS Types 3-6 1 7-5Dialing Restriction During Inbound Trunk Calls for 7-7 TRS Tvpes 3-6Maximum Dialed Digits For TRS Types 3-6 1 7-8 3-Digit Toll Restriction For TRS Types 2-6 7-Digit Toll Restriction For TRS Types 2-6 Dialing Plan Switch 7-9 7-10 7-11 Operator Access7-12International Calling on Extensions 7-13 Country Code TableEqual Access Code Format 7-15Office Code Restriction Table For TRS Types 2-6 7-16 Area Code Table For TRS Types 3-67-17 Office Code Table For TRS Types 3-67-18 Special Area Code Table For TRS Types 3-6Special Office Code Table For TRS Types 3-6 7-20 Special 7-Digit Table For TRS Types 2-67-21 Day TRS Types O-7 for Trunks 1 7-22 Night TRS Types O-7 for Trunks7-23Area Code Table For TRS Types 3-6 (Global Copy)7-24 Office Code Table For TRS Types 3-6 (Global COPY)Area & Office Code Table for TRS Types 3-6 (Glo-7-26 bd COPY)Special Office Code Table For TRS Types 3-6 (Glo- 7-27 bd COPY) Issued 3/l/95DBS 824-10-4007-1
An Overview of Toll RestrictionsUse the Toll Restriction Service (‘IRS) to set limits on the types of calls that can be made from specific extensions or trunksFor example, TRS can prohibit long-distance calls and prevent after-hours callsTRS can also minimize non-business calls and reduce phone bills by permitting only long-distance calls over designated trunks The DBS 824 system supports up to eight different TRS types (see table below) ATRS type can be assigned to each trunk to activate toll restriction Table 7-lToll restriction types TRS TypeCharacteristics 0lFull restriction of outbound dialingl Inbound calls can be answered if trunk is assigned to ring an extension Intercom calls are permittedl Group Call Pickup (intercom calls only) 1Full restriction of outbound dialingl Inbound trunk calls to all phones can be answered and/or transferred l Intercom calls are permittedl Group Call Pickup (intercom calls only) 2lLocal calls (office code dialing) are permitted l-800 calls are permitted 911 calls are always permittedl Inbound trunk calls to all phones can be answered and/or transferredl Full restriction of international calls lFull restriction of operator calls (old dialing plan)l Selectable restriction of operator calls (new NANP dialing plan)l Selectable restriction of speed dial numbersl Selectable restriction of Nil codes (211-811)l Restriction of up to 10 three-digit office codes (new NANP dialing plan)l Restriction of up to 50 seven-digit numbersl Inter-digit timing is set to 6 seconds 3ll-800 calls are permittedl 9 11 calls are always permittedl Full restriction of operator calls (old dialing plan)l Selectable restriction of operator calls (new NANP dialing plan)l Selectable restriction of international calls (defaulted to full restriction -- see Notes’ next page)l Selectable restriction of Nil codes (211-811)l Selectable restriction of speed dial numbersl Restriction of up to 50 seven digit numbersl Trunk calls can be answered and transferredl Defaulted to full restriction of area code dialing (see ‘Notes’ next page)l Defaulted to full restriction of office-code dialing (seeNotes”, next page)l Inter-digit timing is set to 6 seconds 4l Identical to TRS type 3, except that office-code dialing is permitted by default and operator calls are permitted (see “Notes” next page) 5l Programmable TRS type defaulted to no restrictions (see Notes” next page) 6l Programmable TRS type, defaulted to no restrictions (see ‘Notesnext page) 7lNo restriction of outbound dialing Issued 3/l/95DBS 824-10-4007-3
An Overview of Toll RestrictionsFF7 Notes: Operator CallsUnder the old dialing plan, operator calls for TRS types 3-6are permitted if international calls are permitted system-wide (FF7 l# l# l#)The Office Code Tables (FM 3#) are used to restrict all 0+ dialing, the next two digits will also be analyzed(Operator calls are always restricted for TRS types O-2- and always allowed for TRS type 7 ) Under the new NANP dialing plan operator calls can be allowed or restrictedon individual extensions (using FF7 l# 17#), as long as the extension uses a trunk assigned TRS type 2-6(Operator calls are always restricted for TRS types 0 and 1 -- and always allowed for TRS type 7 ) Area Codes and OfSice CodesUnder either dialing plan outgoing calls ontrunks assigned TRS types 3-6 can be allowed or restricted based on the area code and/or office code dialed When a number is dialed, the system first checks arealofice code combinations entered in the “Special Area Code/Office Code Tables” (FF7 # and 5#)If it doesn’t find any restrictions there, the system then checks the ofice codes assigned to TRS types 2-6 as a group (FF7 l# 21#) -- if the system is programmed to use the new NANP dialing planIf not (or if the system doesn’t find a match), it then checks the individual area codes and office codes assigned to individual TRS types in FF7 2# and 3# International CallingUnder the old dialing plan, international calls areallowed or restricted on a system-wide basis using the TRS type assigned to the trunk Under the new NANP dialing plan, international calls on trunksassigned TRS types 3-6 can be allowed or restricted on individual extensions (FF7 l# lS#)Furthermore these extensions can also be programmed to allow or restrict individual calls based on the Country Code dialed (FF7 1# l#and FF7 I# 19#)7-4 DBS 824-l O-400 Issued 3/l /95
FF7international Calling For TRS Types 3-6 International Calling For TRS Types 3-6 Software VersionCPC-S and CPC-M, Version 1 0 and higher Address FF7 l# I# (0 or l)# DescriptionUse this program to set system-wide restrictions for the dialing of international calls on trunks assigned TRS types 3-6 If the DBS 824 system is programmed to use the new AJANP dialing plan (FF7 l# 16# l#), this “International Calling For TRS Types 3-6” program determines whether the system will check the Country Code Table for any restrictions on the dialed number If the DBS 824 system is programmed to use the old dialing plan (FF7l# 16# O##), this “International Calling For TRS Types 3-6” program determines whether international calling is allowed or restricted system-wide This program only applies to those trunks that are assigned TRS types 3-6 International calls are always restricted for TRS types 1 and 2 -- and always allowed for TRS type 7 Programming IFF7 l# I# (0 or l)# t Old Dialing PlanO=International calls are restricted l=Intemational calls are permitted New Dialing Plan (NANP)O=System will check Country Code Table for restrictionsl=System will not check Country Code Table for restrictions (all international calls are allowed) Related ProgrammingDialing Plan Switch FF’7 l# 16# (0 or l)#Country Code Table FF7 l# 19# (Table)++ (Code)+!Override Toll Restrictions with SSD Numbers FFl 2# l# 4## (SSD)#System Installation Area Code FFl 2# l# 17# (0 or l)# Issued 3/l /95DBS 824-l O-4007-5
International Calling For TRS Types 3-6FF7 NotesRestricting International Calls On Individual ExtensionsIf the new NAWdialing plan is used, individual extensions can be set for allowing/restricting international calls based on the Country Code Table, using program address FF7 l# 18# Including “011” in Ome Code Tables for International CallingIf international calls are permitted, 011 should be permitted in office code tablesfor TRS types 3-6 7-6DES 824-l O-400Issued 3/l !95
FF7Dialing Restriction During Inbound Trunk Calls for TRS Types 3-6 Dialing Restriction During Inbound Trunk Calls for TRS Types 3-6 Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF7 I# 2# (0 or l)# DescriptionUse this program to prevent users from circumventing restrictions on outside calling If TRS types 3-6 are set to prevent outside calling, users may try to circumvent the restriction in the following manner lThe user receives an outside call l During the outside call, the user presses FLASH, causing the phone torelease and reseize the trunk lThe user dials an outside number on the trunk, thus circumventing the restriction To prevent circumvention of the restriction, use this program to restrict dialing during inbound trunk calls for TRS types 3-6 ProgrammingFF7 1# 2# (0 or l)# $ O=When an incoming call is received,the FLASH key cannot be used to originate an outgoing call l=When an incoming call is received, the FLASH key can be used to originate an outgoing call Issued 3/l 195DBS 824-l O-4007-7