Panasonic Dbs 824 Instructions Manual
Have a look at the manual Panasonic Dbs 824 Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
tt1ejusy lone (t51j uerecrron 11mer Busy Tone (BT) Detection Timer Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 3# 27# (0-15)# DescriptionUse this program to set the amount of time the DBS 824 will wait to detect a busy tone from the CO before automatically rediaiing an outgoing callIf a busy tone is not detected within this amount of time, the DBS 824 will not automatically redial the number Programming FFl 3# 27# (0115)# f Timer Setting (Default=3 see the following table) Table l-30 BT detection timer values Number 0ValueNo restriction (system will wait indefinitely) 2 seconds 4 seconds II+-- I13 6 seconds 8 seconds 10 seconds 12 seconds 14 seconds 16 seconds i 30 seconds Issued 3/l/95DBS 824-10-4001-113
Busy Tone (BT) Detection TimerFFlRelated Programming Auto Repeat Dialing Count FFl 2# l# 3447 (0-15)## Wait Timer For Auto-Repeat Dialing FFl 3# 26# (0- 15)# Dial Tone (DT) Detection Timer FFl 3# 28# CO Busy Tone (BT) Detection for Auto-Repeat DialingFF2 (Trunk)# 22# 1-114DBS 824-l O-400Issued 3/l /95
FFlDial Tone (DT) Detection Timer Dial Tone (DT) Detection Timer Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 3# 28# (O-255)44 DescriptionUse this program to set the amount of time (in milliseconds) the DBS 824 willwait to detect a dial tone from the CO, before automatically redialing an outgoing callIf a dial tone is not detected within this amount of time auto- repeat dialing will not be carried out. Programming I FFl 3#$ 28# (01255)# $Timer Setting (Default=25,see the following table for values) Table I-31 DT detection timer values Number 01200 ms Value (in milliseconds) 14Oms t2180ms I 120 ms 4 24 160 ms960 ms (increments of 40 ms) 251,000 ms(or 1 second) 26 1,040 ms 272551,080 ms10,200 ms (or 10 2 seconds) Related ProgrammingAuto-Repeat Dialing Count FFl 2# l# 34# (0-15)# Wait Timer For Auto-Repeat Dialing FFl 3# 26# (0-15)# Busy Tone (BT) Detection Timer FFl 3# 27# (0- 15)# CO Busy Tone (BT) Detection for Auto-Repeat DialingFF2 (Trunk)# 22# Issued 3/l /95DBS 824-l O-4001-115
Automatic Night 2 fviode Start TimeFFl Automatic Night 2 Mode Start Time Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 3# 29# HHMM# DescriptionThis option sets a time for the DBS 824 to automatically switch from ‘Night 1 ’ to ‘Night 2” mode This program uses the 24-hour time format Programming To set the automatic Night 2 mode start time FFl 3# 29# (0000-2359)# f Night 2 Mode Start Time (in 24-hour format) To disable the automatic Night 2 mode start time I ~~FFl 3## 29## CONF ON/OFF Related ProgrammingTime Setting FFl l# 2# HHMM#Automatic Day Mode Start Time FFl 3# 25# HHMM#Automatic Night 1 Mode Start Time FFl 3# l# HHMM# NotesIntetaction with the System Clock.Automatic “Night 2” start time depends on the accuracy of the DBS 824 clock 1-116DES 824-10-400issued 3/l/95
FFlRemote Programming ID Code Remote Programming and DISA Codes Remote Programming ID Code Sofhnrare VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 4## (0000-9999)# DescriptionThe Remote Programming ID Code allows you to enter the terminal programming modeThis programming mode is used to enter programming commands from a remote PC or a local PC connected directly to the SMDR port (CNl) You can enter the remote programming mode through any of these three methods lBy dialing into the system through a direct DISA trunk lBy dialing into the system through a regular CO trunk, then requesting the operator to enter the Remote Programming ID Code lBy using a local PC and communications package to connect directly to the DBS serial port For more information on the terminal programming mode, see Appendix B Programming To set the remote programming ID code FFl 4## (0000-9999) t 4-Digit ID Code To reset the ID code to the default (9999) IFFl 4## CONF ON/OFFI I s&ed 3/l /95DBS 824-l O-400l-117
DISA Inbound Call ID CodeFFl DISA Inbound Call ID Code Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 5# (0000-9999)# DescriptionThis program allows you to enter a DISA ID code Once a caller has dialed into the DBS 824 using a DISA trunk, dialing this code provides direct access to intercom dial tone Programming To set the DISA ID code FFl 5# (OOOO-9999)# t 4-Digit ID Code To clear the DISA ID code FFl !5## CONF ON/OFFI Related ProgrammingDISA Outbound Call XD Code 1 FFl 6# l# (0000-9999)#DISA Outbound Call ID Code 2 FFl 6# 2# (0000-9999)#DISA Start Time FE2 (Trunk)# 19#DISA End Time FF2 (Trunk)# 20# DISA Auto Answer FE2 (Trunk)# 11# NotesDlSA Dial ToneThe default setting of the DBS 824 supplies intercom dial tone to a CO trunk defined as a DISA trunk If a DESA ID code is stored in place of the default setting (via remote programming), a DISA dial tone (fast busy tone) will be heard instead of intercom dial tone The DISA dial tone is a signal to proceed with your call until you enter the stored DISA ID code After the DISA ID code is entered, the intercom dial tone is presented This provides the opportunity to make an extension call To make an outbound CO trunk call, enter #7, dial 9 or 8 l-86 (to access a CO trunk), then dial the 4digit DISA ID code 1-118DBS 824-l O-400Issued 3/l /95
FFlDISA Outbound Call ID Code 1 DISA Outbound Call ID Code 1 Software Version CPC-S and CPC-M, Version 1 0 and higherAddress FF1 6# l# (0000-9999)# DescriptionOnce a DISA caller has entered the system he/she can make an outside call after entering a valid ID code This program sets the first of two valid DISA Outbound Call ID Codes Thesystem will accept either code to give the DISA caller an outside line(The purpose of having two Outbound Call ID Codes is to be able to track two groups of DISA callers on SMDR reports ) Programming To assign the DISA Outbound Call ID Code 1 FFl 6# l# (OOOO-9999)# t 4-Digit ID Code (Default=llll) To reset the ID code to the default valuer FFl 6# l# CONF ON/OFF Related Programming DISA Auto AnswerFF2 (Trunk)# 11# (0 or I)#DISA Inbound Call ID Code FFl 5# (0000-9999)# DISA Outbound Call ID Code 2FFl 6# 2# (0000-9999)#DISA Start lime FF2 (Trunk)# 19# (HHMM)#DISA End Time FF2 (Trunk)# 20# (HHMM)# Issued 3/l /95DES 824-l O-400l-119
DISA Outbound Call ID Code 2FFl DISA Outbound Call ID Code 2 Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 6## 2# (0000-9999)# DescriptionOnce a DISA caller has entered the system, he/she can make an outside call after entering a valid ID code This program sets the second of two valid DISA Outbound Call ID Codes The system will accept either code to give the DISA caller an outside line (The purpose of having two Outbound Call ID Codes is to be able to track two groups of DISA callers on SMDR reports ) Programming To assign the DISA Outbound Call ID Code 2 IFFl 6# 2# (OOOp9999)# 4-Digit ID Code (Def aul t=9999) To reset the ID code to the default value FFl 6# 2# CONF ON/OFFI Related Programming DISA Auto AnswerFF2 (Trunk)# ll# (0 or l)# DISA Inbound Call ID CodeFFl 5# (0000-9999)# DISA Outbound Call ID Code 1 FFl 6# l# (0000-9999)#DISA Start lime FF2 (Trunk)# 19# (HHMM)#DISA End Time FF2 (Trunk)# 20# (HHMM)#l-120 DBS 824-l O-400Issued 3/l /95
Programming Authorization Code ID Code For System Programming Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 7# (OOOO-9999)# DescriptionThis program assigns an ID code that can be dialed from a non-attendant phone to enter the programming mode Non-attendant extensions enter the programming mode by dialing #I98 and then the ID Code entered in this address Programming To assign the ID code for system programming Notes I FFl 7# (OOOO-9999)# f 4-Digit ID Code (Default=9!3!8) To reset the ID code to the default value FFl 7# CONF ON/OFF Entering the Programming ModeOnly one non-attendant extension can be a programming extension at a particular time Issued 3/l/95DBS 824-10-400l-121
New Function ResetFFl New Function Reset New Function Reset Software Version CPC-S and CPC-M, Version 1 0 and higherAddress FFl 8## 1# (01l)# DescriptionThis feature is reserved for future use New Function Reset Confirmation Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress: FFl 8# 2# (O-l)# DescriptionThis feature is reserved for future use 1-122 DBS 824-l O-400 Issued 3/l /95