Panasonic Dbs 824 Instructions Manual
Have a look at the manual Panasonic Dbs 824 Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
FFlCO-to-CO Talk Mode Control CO-to-CO Talk Mode Control Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 2# l# 38## (0 or l)# DescriptionUse this address to determine whether the DBS 824 system will use an internal conference circuit for trunk-to-trunk conference calls or whether it will connect the trunks directlyThe CO-to-CO Talk mode is entered via the Call Forward-Outside feature or the DISA Outgoing functionIf an audio loop-back problem occurs when trunks are connected directly, reset this program address to “Use a conference circuit” Programming 1 FFl 2# l# 38## (0 or l)# t O=Connect the trunks directly (Default) 1 =Use a conference circuit. Related ProgrammingAutomatic DISA Callers FFl 2# 8# (l-lO)# (PhoneNo )#Unsupervised Conference Timer FFl 3# 9# (0-15)# Unsupervised Trunk ConferenceFF2 (Trunk)# 16# (0 or l)#Unsupervised ConferenceFF3 (ExtPort)# 13# (0 or l)# NotesLimihdion On Availability Of Conference Citcuii?sThe system can support up to three conference circuits at a timeIf this programming address is set to “1” (use a conference circuit), and a fourth CO-to-CO call is attempted while three other conference calls are currently in progress, the system will connect the trunks in the fourth call directly to each other Issued 3/l/95DBS 824-10-400Page1-43
Parity Check (SMDR)FFl SMDR Data (Serial Port CNl) Parity Check (SMDR) Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 2# 2# l# (0 or l)## DescriptionThis program determines whether the DBS 824 uses parity checking over serial port CNl, which is normally dedicated for SMDR If this address is set to “on,” use FFl 2# 2# 2# (0 or l># to select even or odd PetY Programming I I FFl 2# 2# l# (0 or l)# f O=Turns off the parity check l=Turns on the parity check Related ProgrammingOdd/Even Parity (SMDR) FFl 2# 2# 2# (0 or l)# NotesChecking Communications ParametersBe sure to properly set all communication programming addresses when modifying any single address valueCommunication parameters for SMDR are set with addresses FF12# 2# 1 through 9#Page l-44 DBS 824-l O-400Issued 3/l 195
FFlOdd/Even Parity (SMDR) Odd/Even Parity (SMDR) Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 2# 2# 2# (0 or l)## DescriptionIf the parity check for SMDR serial port CNl has been set (FF12# 2# l#), this option determines whether the check is based on an even count or an odd count. Programming 11 FFl 2# 2# 2# (0 or l)# t O--odd parityl=Even parity NotesChecking Communications ParametersBe sure to properly set all communication programming addresses when modifying any single address value Communication parameters for SMDR are set with addressesFFl2# 2# 1 through 9#Issued 3/l/95DBS 824-l O-400Page 1-45
Baud Rate (SMDR)FFl Baud Rate (SMDR) Software Version CPC-S and CPC-M, Version 1 0 and higherAddress FFl 2# 2# 3# (l-4)# DescriptionThe data transmission speeds between SMDR serial port CNl and peripheral equipment can be set from 300 bits per second to 9600 bits per second Programming FFl 2W 2# 3## (54)# f 1=300 bps 2=1200 bps 3=2400 bps 4=9600 bps NotesChecking Communications ParametersBe sure to properly set all communication programming addresses when modifying any single address valueCommunication parameters for SMDR are set with addresses FFl 2# 2# 1 through 9# Page 1-46DES 824-l O-400issued 3/l 195
FFlStop Bit Lenqth (SMDR) Stop Bit Length (SMDR) Software VersionCPGS and CPC-M, Version 1 0 and higherAddress FFl 2# 2# 4## (l-3)# DescriptionThis program sets the length of the stop-bit parameter for transmitted data over SMDR serial port CNl Proghmming FFl 2# 2# 4## (1 to 3)# t l=l bit 2=I 5 bits 3=2 bits NotesChecking Communications ParametersBe sure to properly set all communication programming addresses when modifying any single address valueCommunication parameters for SMDR are set with addresses WI 2# 2# 1 through Y# Issued 3/l/95DBS 824-10-400Page 1-47
Data Length (SMDR)FFl Data Length (SMDR) Software VerskdPC=S and CPC-M, Version 1 0 and higherAddress FFl 2# 2# 5# (3 or 4)# DescriptionThis program sets the length of the transmitted data string at 7 or 8 bits, over SMDR serial port CNl Programming II FFl 2# 2# 5## (3 or 4)# t 3=7 bits 4=8 bits NotesChecking Communicaticins ParametersBe sure to properly set all communication programming addresses when modifying any single address valueCommunication parameters for SMDR are set with addresses FF1 2# 2#1through9#Page l-48 DBS 824- 1 O-400Issued 3/l 195
FFlSMDR Serial Port Flow Control (XON / XOFF) SMDR Serial Port Flow Control (XON / XOFF) Software Version CPC-S and CPC-M, Version 1 0 and higherAddress FFl 2# 2# 6# (0 or l)# DescriptionUse this address to determine whether the DBS 824 system will control the flow of data to the SMDR device connected to serial port CNl If “XON/XOFF” is activated in this address, the DBS 824’s software will stopthe flow of data when the SMDR device s memory buffer becomes full and resume the flow when the buffer empties ‘XON/XOFF ’ should be deactivated (default setting) if a flow control mechanism is present elsewhere in the interface (i e in the printer or RTS and CTS lines)A flow control mechanism should always be present in orderto prevent data from being lost during transmission Programming FFl 2# 2# 6## (0 or l)# t O=Turns off “XONIXOFF” (824 software does not control data flow) 1 =Tums on “XON/XOFF” (824 softwarecontrols data flow) NotesDBS 824 Buffer SizeThe size of the DBS 824 buffer for SMDR is 1,000 bytesThis is the maximum amount of data that the system can hold while the SMDR device is emptying its buffer Issued 3/l/95DBS 824-l O-400Page l-49
SMDR Printing Mode 1 Outbound and InboundFFl SMDR Printing Mode 1: Outbound and Inbound Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 2# 2# 7# (0 or l)# DescriptionThe SMDR printer can record data for only outgoing calls or for both outbound and inbound calls Progiamming FFl 2# 2# 7# (0 or l)# f O=Outbound only kInbound and outbound NotesActivating SMDR Mode after Using the Bus Monitor ModeLf the DBS 824is in Bus Monitor Mode, the SMDR Mode must be reactivated to resume SMDR output. To reactivate SMDR mode from any extension press ON/OFF ##90 ON/OFF (to empty buffer), then ON/OFF ##!I3 ON/OFF (to activate SMDR mode) Page l-50 DBS 824-l O-400Issued 3/l /95
FFlSMDR Printing Mode 2. Long-Distance and Local Calls SMDR Printing Mode 2: Long-Distance and Local Calls Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FFl 2# 2# 8# (0 or l)# DescriptionThe SMDR printer can record data on only long-distance calls or on all types of outbound calls Pro$ramming FFl 2# 2# 8# (0 or l)# t O=Long-distance only l=Local and long-distance Issued 3/l /95DBS 824-l O-400Page l-51
SMDR Printing Mode 3 Header TitleFFl SMDR Printing Mode 3: Header Title Software VersionCPC-S and CPC-M, Version 1 0 and higherAddress FF1 2# 2# 9# (0 or l)# DescriptionTitles such as “Time,” “Duration,” and “COW are printed every 60 lines on the SMDR report if this feature is enabled Programming FFl 2# 2# 9# (0 or l)# t O=Turns off tlie header l=Turns on the headerPage l-52 DBS 824-l O-400Issued 3/l /95