Home
>
Triad
>
Telephone
>
Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual
Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual
Have a look at the manual Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 9 Triad manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Camp On2-53 Chapter 2 - Features and Operation Conditions » The CAMP ON button can be assigned on 8-button phones using code 620. » Calls cannot be camped on when a station is in DND or in Conference. » If the party that initiated the Camp On hangs up, then Camp On is canceled and the call is blind-transferred. Camp On Button Flash Rate Description The Camp On button flash rate is the rate at which the Camp On button flashes when you receive a Camp On. This flash rate can be programmed to 29 different options identified in the flash rate table. This enables the programmer to customize the key system configuration to desired flash rates. Programming Steps 1. Press the CAMP ON BTN flexible button (FLASH 07, Button #15). The following message displays: 2. Enter a valid number (00-28) on the dial pad to correspond to one of the 29 available options. (Refer to Table 2-14 on page 2-148.) 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. DEFAULT … Camp On Button flash rate is set for a Red 120 ipm Flash (10). Camp On Recall Description When a station does not answer a Camp On, that call recalls the person placing the Camp On, and if unanswered by them, recalls the Attendant(s). CAMP ON BTN 00-28 RED 120 IPM FLASH
2-54Centrex/PBX Chapter 2 - Features and Operation Centrex/PBX The XTS provides features that are Centrex compatible so that Centrex users can utilize the XTS System to enhance their Centrex capabilities. The system actually simplifies and provides easier access to many Centrex features by offering the following features. CO / PBX Programming Description Each individual outside line connected to the system may be programmed as a CO or PBX line. Use the PBX mark when identifying Centrex lines. Programming Steps 1. Press FLASH and dial [40]. The following message displays: 2. Enter a valid number for the range of lines being programmed. If only one line is being programmed, enter that number twice (001 001). 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. Flexible button #19 (Page A) is lit. The following message displays to indicate current programming of that line or group of lines: XXX-XXX = CO Line Range 4. Press the CO/PBX flexible button (Button #2). 5. Enter a 0 or 1 which corresponds with the following entries: [0] = PBX [1] = CO 6. Press HOLD to save the entry. A confirmation tone sounds. DEFAULT … All lines are assigned as CO lines. CO L IN E AT TRIBUTES SELECT A CO LINE RANGE If HOLD is pressed without entering a CO range, ALL CO lines are selected. XXX - XXX PAGE A ENTER BUTTON NUMBER PBX / CO 0-1 CO
Centrex/PBX2-55 Chapter 2 - Features and Operation Off-Hook Preference Description Telephones, key and SLT, may be programmed to have their personal Centrex line accessed automatically just by lifting the handset or pressing the ON/OFF button (Speaker Button on SLTs). Internal features to the XTS are still made available to digital telephones by accessing intercom before going off-hook. Refer to “Ring Down/Hot Line/Off-Hook Preference” on page 2-247. Private Line Appearance Description The XTS allows for private line assignment on an unlimited basis. Each station may have sole access to a particular outside line if desired and may also be assigned to receive incoming ringing on that line. Refer to “CO Line Group Programming” on page 2-74, “Line Group Access - Station” on page 2-72, and “Flexible Button Assignment” on page 2-148. Programming , #, and Hook-Flashes into Speed Dial Description Many Centrex codes utilize a hook-flash followed by, in many cases, the digit [] and or [#]. The XTS allows programming of these codes as a part of system or station speed dial sequences. Refer to “Speed Dial” on page 2-256. Centrex/PBX Flash Description Provides telephone users with the ability to terminate an outside call or transfer a call behind a PBX or Centrex and restore dial tone without hanging up the handset. A FLASH button is located on each digital telephone. Operation When connected to an outside line: Press FLASH to disconnect outside line and reseize outside line dial tone. SINGLE LINE TELEPHONE Depress the hookswitch briefly; or if equipped with a flash key, depress it. Conditions » 8-button telephones can assign a FLASH button by using code [660].
2-56Centrex/PBX Chapter 2 - Features and Operation Centrex/PBX Flash Timer Description Flash is a programmable opening on a line for signaling. When using an outside line, flash lets a user obtain a new dial tone without losing the line. This is particularly useful behind a PBX or Centrex. Each CO line can be programmed for a flash time. Programming Steps 1. Press FLASH and dial [40]. The following message displays: 2. Enter a valid number for the range of lines being programmed. If only one line is being programmed, enter that number twice (001 001). 3. Press Button #21 to select Page C. The display updates. The following message displays to indicate current programming of that line or group of lines: XXX-XXX = CO Line Range 4. Press the FLASH TIMER flexible button (Button #1). 5. Enter a valid number on the dial pad (01–20) which corresponds to 100 ms to 2 seconds. 6. Press HOLD to save the entry. A confirmation tone sounds and the display updates. DEFAULT … Flash Timer is set for 10 (1.0 seconds) and is variable from 01-20 (100 ms to 2seconds). Centrex / PBX Transfer Description When Centrex or PBX lines are connected to the XTS, users may, by using the Flash button, transfer callers to other Centrex or PBX extensions. The Flash command may also be included within a Speed Bin and programmed onto a flexible button for one button transfer. Consult your Centrex user guide for further instructions after flashing the line. Refer to “Centrex/PBX Flash Timer” on page 2-56. CO LIN E AT TRIBUTES SELECT A CO LINE RANGE If HOLD is pressed without entering a CO range, ALL CO lines are selected. XXX - XXX PAGE C ENTER BUTTON NUMBER FLASH TIMER 01-20 10
Centrex/PBX2-57 Chapter 2 - Features and Operation Operation While connected to an outside line (PBX/Centrex): 1. Press the FLASH button. Receive transfer dial tone. 2. Dial a PBX/Centrex station number. 3. Hang up to complete the transfer. PBX Dialing Codes Description Five 1- or 2-digit PBX access codes can be programmed into memory. When dialed, these codes signal the system so toll restriction is applied at the next dialed digit. When a single digit code [9] is entered, it must be followed by [#] as the second digit. Refer to “911 Feature” on page 2-4. Programming Steps 1. Press FLASH and dial [12]. The following message displays: 2. Enter valid numbers (one right after the other) on the dial pad, up to ten digits. If a single digit code is required, enter the code followed by [#]. 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 4. To delete a code, enter [#] [#] and press HOLD. DEFAULT … No PBX dialing codes are assigned. Conditions » Lines must be programmed as PBX lines before these codes apply. If 911 is enabled for a PBX trunk using Centrex, entry one in Flash 12 (of [9] + [#]) will insert the Centrex 9 (not LCR). Quick Reference Flash 40 Page A Button #2 PBX/CO (Refer to “CO / PBX Programming” on page 2-54.) PBX DIAL CODES ##, ##, ##, ##, ##
2-58Class Of Service Chapter 2 - Features and Operation Class Of Service Description Each station and each CO line is assigned a Class of Service (COS) which governs stations’ dialing privileges. Day COS and Night COS assignments to stations provide the system administrator additional control over station dialing, preventing misuse of phones after hours. Seven uniquely defined COSs are available for assignment to stations and five uniquely defined COSs are available for assignment to CO lines. Station COS works in conjunction with CO line COS to provide the most flexible means for offering custom toll restriction. The following table depicts how the station and CO line COSs interact. After setting the station COS, any change to the CO line COS will result in a change in dialing privilege. For example, a station COS of 2 with a CO line COS of 5 gives the user an unrestricted calling privilege. Related Information Table 2-2: Class of Service (COS) S T A T I O N C O SCO Line Class of Service 12345 1Unrestricted Unrestricted Unrestricted Canned Restricted*Unrestricted 2Table A Table A Unrestricted Canned Restricted*Unrestricted 3Table B Unrestricted Table B Canned Restricted*Unrestricted 4Table A and B Table A Table B Canned Restricted*Unrestricted 5Canned Restricted*Canned Restricted*Canned Restricted*Canned Restricted*Unrestricted 6Intercom Only Intercom Only Intercom Only Intercom Only Intercom Only 7Canned Restricted*Canned Restricted*Canned Restricted*Canned Restricted*Unrestricted * Canned Restriction: No [0], [1], [#], [*] as first dialed digit, and 7-digit dialing limitation; plus 1-800, 1- 888, 1-866, 1-877, 1-911, 1-611 are allowed, and 411, 976, and 555 numbers are denied. COS 7 allows 10- digit dialing maximum. Quick Reference Flash 70 Toll Restriction (Refer to “Toll Restriction” on page 2-296.)
Class Of Service2-59 Chapter 2 - Features and Operation Class of Service - CO Line Description Through assignments of a CO Line Class of Service, the assigned CO line interacts with a station Class of Service. Programming Steps 1. Press FLASH and dial [40]. The following message displays: 2. Enter a valid number for the range of lines being programmed. If only one line is being programmed, enter that number twice (001 001). 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. Flexible button #19 (Page A) is lit. The following message displays to indicate current programming of that line or group of lines: XXX-XXX = CO Line Range 4. Press the LINE COS flexible button (FLASH 40, Page A, Button #9). 5. Enter a valid number on the dial pad (1-5) corresponding to one of five possible Classes of Service to which a CO line may be assigned: [1] = COS1; No restrictions [2] = COS2; Table A governs, Station COS 2 and 4 are monitored [3] = COS3; Table B governs, Station COS 3 and 4 are monitored [4] = COS4; Restricts [0], [1], [*], [#] dialed as first-digit and places a 7-digit dialing limitation. Allowed are: 1-800, 1-888, 1-866, 1-877, 1-911, and 1-611. Denied are: 411, 976, and 555. [5] = COS5; Overrides Station COS 1, 2, 3, 4, 5, and 7, and allows unrestricted dialing. 6. Press HOLD to save the entry. A confirmation tone sounds and the display updates. DEFAULT … Class of Service setting is 1. CO LIN E AT TRIBUTES SELECT A CO LINE RANGE If HOLD is pressed without entering a CO range, ALL CO lines are selected. XXX - XXX PAGE A ENTER BUTTON NUMBER CLASS OF SERVICE 1-5 1
2-60Class Of Service Chapter 2 - Features and Operation Station Day Class of Service Description Each station must be assigned a certain COS for Day Mode operation and for Night Mode operation. Class of Service (COS) determines the station’s dialing privileges. Use Flash 50 programming when you want to modify a range of stations’ attributes using fixed station numbers. Use Flash 51 programming to modify a single station’s attributes using a flexible station number. Programming Steps 1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of the following messages displays: 2. Enter the range of fixed station numbers (100-351) to be programmed. If only one station is being programmed, enter that number twice, e.g., [100 100]. -or- Enter a valid flexible number (100-8999) to be programmed. 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. Flexible button #19 is lit. The display updates to reflect current programming for Page A: 4. Press button #20. The display updates to reflect current programming for Page B. Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers STATION ATTRIBUTES SELECT A STATION RANGEENTER STATION NUMBER If HOLD is pressed without entering a station range, ALL stations are selected. Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers XXX - XXX PAGE A ENTER BUTTON NUMBERSXXX PAGE A ENTER BUTTON NUMBER XXX-XXX = fixed station range XXX = 3- or 4-digit flexible number Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers XXX - XXX PAGE B ENTER BUTTON NUMBERSXXX PAGE B ENTER BUTTON NUMBER XXX-XXX = fixed station range XXX = 3- or 4-digit flexible number
Class Of Service2-61 Chapter 2 - Features and Operation 5. Press the DAY COS flexible button (Button #2). 6. Enter a valid number on the dial pad (1-7) corresponding to one of seven possible Classes of Service to which a station may be assigned. The seven classes of service are: [1] = COS 1; No restrictions [2] = COS 2; Table A governs [3] = COS 3; Table B governs [4] = COS 4; Table A and B govern [5] = COS 5; Restricts [0], [1], [ ], [#] dialed as first-digit with a 7-digit maximum [6] = COS 6; Intercom Only (no CO line access - results in a 911 block unless 911 Feature is active) [7] = COS 7; Restricts [0], [1], [ ], [#] dialed as first-digit with a 10-digit maximum 7. Press HOLD to save the entry. A confirmation tone sounds and the display updates. DEFAULT … All stations are assigned a COS 1 for Day Mode. Conditions » Only one station at a time can be programmed when using a flexible station number. » When in Flash 51 programming, if you press HOLD without specifying a flexible number to be programmed, you will get the station that is in port/station 100. Station Night Class of Service Description Each station must be assigned a COS for Night Mode operation. The Night COS goes into affect when the system is manually or automatically placed into Night Mode. This prevents misuse of phones after hours. Class of Service (COS) determines the station’s dialing privileges. Use Flash 50 programming when you want to modify a range of stations’ attributes using fixed station numbers. Use Flash 51 programming to modify a single station’s attributes using a flexible station number. DAY COS 1-7 1
2-62Class Of Service Chapter 2 - Features and Operation Programming Steps 1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of the following messages displays: 2. Enter the range of fixed station numbers (100-351) to be programmed. If only one station is being programmed, enter that number twice, e.g., [100 100]. -or- Enter a valid flexible number (100-8999) to be programmed. 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. Flexible button #19 is lit. The display updates to reflect current programming for Page A: 4. Press button #20. The display updates to reflect current programming for Page B. 5. Press the NIGHT COS flexible button (Button #3). a Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers STATION ATTRIBUTES SELECT A STATION RANGEENTER STATION NUMBER If HOLD is pressed without entering a station range, ALL stations are selected. Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers XXX - XXX PAGE A ENTER BUTTON NUMBERSXXX PAGE A ENTER BUTTON NUMBER XXX-XXX = fixed station range XXX = 3- or 4-digit flexible number Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers XXX - XXX PAGE B ENTER BUTTON NUMBERSXXX PAGE B ENTER BUTTON NUMBER XXX-XXX = fixed station range XXX = 3- or 4-digit flexible number NIGHT COS 1-7 1