Home
>
Triad
>
Telephone
>
Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual
Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual
Have a look at the manual Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 9 Triad manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ProgrammingC-13 Appendix C - Networking Systems Programming Programming must be done with a 24-button display telephone or with WinDBA. It is recommended that WinDBA be used for network programming. The following sections describe programming steps that pertain to networking. Each section assumes that you have already entered system programming. The following sections provide a detailed description of programming steps necessary for networking. A Quick Start procedure is provided at the end of this document as an aid to understanding the flow of programming. Node/Hub Identification Programming Description In networking, there must be a central Hub. All communication within the network must be linked via the Hub. The Hub should be identified as system 1. Each Node should be identified with its own unique number between 2 and 16. Networking requires 4-digit dialing. Complete the following programming steps to specify numbers that identify Hub/Nodes and to specify the leading digit to be used for dialing. Programming Steps 1. Press FLASH and dial [09]. The following message displays: 2. Press Button #8. The following message displays: 3. Dial a valid number (01-16) to identify the system by number. 4. Press HOLD to save the entry. 5. Press Button #9. The following message displays: 6. Dial a valid number (0-8) to identify the desired leading digit. SYSTEM PARAMETERS ENTER BUTTON NUMBER SYSTEM NODE 1-16 01 The Hub should be identified as system 1. Each Node should be identified with its own unique number between 2 and 16. LEADING DIGIT 0-8 0
C-14Programming Appendix C - Networking Systems 7. Press HOLD to save the entry. Networking Tables Programming Description The Networking Table is used to route calls between systems. It identifies the table number (01-16), the CO Group (00-23), the range of station numbers (from xxxx to xxxx), which card sends DSS/BLF information to an external location (programming for external BLF is only done on the Hub system), and whether the Status Check is enabled or disabled. The Table Number establishes the sequence that the system uses to search for a match to the number being called. The system searches based on table number 01 parameters. If no match is found, then the system searches based on table number 02 parameters. This process continues until a match is found and the call is placed, or no match is found and the caller receives an error tone. An automatic Status Check is designed to cope with unique network configurations that have a system’s extension range that overlaps another system’s extension range. Status Check screens a call to determine if the station number is assigned within the network. If the extension number is unassigned, the call is not forwarded to another system in the network and the caller receives an error tone. EXAMPLE OF THE ISSUE -- System A has station numbers 6005, 6006, 6007, 6024 and 6048; System B has station numbers 6008, 6009, 6010, 6025, and 6049. Station number 6022 is not assigned. In this example, both Systems have overlapping station ranges. A problem can occur when an incoming call for station number 6022 enters System A. System A checks to determine if this is an assigned number within System A. Since it is not an assigned number within System A, the call is forwarded to System B. System B completes the same process, then forwards the call back to System A, etc. Networking Tables For Nodes (refer to Figure C-11 and Figure C-12 ) Table Number 01 of a Node’s networking tables should include: CO Group = valid CO Group Number 01-23 Extension Range = the Node’s extension range Table Number 02 of a Node’s networking tables should include: CO Group = valid CO Group Number 01-23 Extension Range = entire network’s extension range Table Number 03 of a Node’s networking tables should include: CO Group = CO Group Num ber 00 Extension Range = complete range of possible extension numbers (i.e., 1000-8999) Only 3-digit codes will be changed to include a leading digit, e.g., 2-digit codes such as group call pickup (#0) are not affected. You should use the disabled setting for Status Check if your network has no overlapping ranges. To maximize routing efficiency for a system with overlapping station ranges, it is recommended that you enable the remote system’s Status Check.
ProgrammingC-15 Appendix C - Networking Systems The system will screen and process calls in the following sequence: If the call matches an extension specified in Flash 52 programming, the call will be connected within the same system. -or- If the call matches an extension associated with Table Number 02, the call will be routed to the appropriate remote device. -or- If the call matches an extension associated with Table Number 03, the caller will receive an error tone. Networking Tables For the Hub (refer to Figure C-11 and Figure C-12 ) Table Number 01 of a Hub’s networking tables should include: CO Group = valid CO Group Number 01-23 Extension Range = the Hub’s range of extension numbers Table Number 02 of a Hub’s networking tables should include: CO Group = valid CO Group Number 01-23 Extension Range = the first Node’s range of extension numbers External Busy Lamp Field Slots = numbers identifying PRIB slot locations associated with each Node in the network, other than the Node being defined Table Numbers greater than 02 of a Hub’s networking tables (one Table Number to define each Node) should include: CO Group = valid CO Group Number 01-23 Extension Range = the Node’s range of extension numbers External Busy Lamp Field Slots = numbers identifying PRIB slot locations associated with each Node in the network, other than the Node being defined The last Table Number of a Hub’s networking tables should include: CO Group = CO Group Num ber 00 Extension Range = complete range of possible extension numbers (i.e., 1000-8999)
C-16Programming Appendix C - Networking Systems Figure C-11: Two-Node Networking Table Example LEGEND: Table Number = the identification number assigned to each array within the system. CO Group = the line group used to access each system. Co Group 00 = internal calls only. Extn Range = the extension numbering range for the array. Ext BLF Slot = identifies PRIB slot locations in the Hub that are associated with each Node within the network, other than the Node being defined by the Table Number row. This allows DSS/BLF updates to be sent to the correct systems within the network. Node systems do not identify Ext BLF Slot locations because the Hub system controls passing of information.SYSTEM 2 SYSTEM 1 (HUB) SYSTEM 3 Ext 1000 – 1999 Ext 2000 – 2999 Ext 3000 – 3999 PRIB Slot 7 PRIB Slot 2 CO Group 02 CO Group 02 PRIB Slot 3 PRIB Slot 4 CO Group 03 CO Group 02 Actions notify System 1 (e.g., on/off hook)Actions notify both System 2 and System 3Actions notify System 1 Table Number CO Group Extn Range Ext BLF Slot Table Number CO Group Extn Range Ext BLF Slot Table Number CO Group Extn Range Ext BLF Slot 01 00 1000 - 1999--- 01 00 2000 - 2999-- 01 00 3000 - 3999--- 02 02 1000 - 3999--- 02 02 1000 - 19993 02 02 1000 - 3999--- 03 00 1000 - 8999--- 03 03 3000 - 39992 03 00 1000 - 8999--- …. to ….--- 04 00 1000 - 8999---…. to …. …. to ….…. to ….…. to …. 16…. to ….--- 16…. to ….16…. to ….---
ProgrammingC-17 Appendix C - Networking Systems Figure C-12: Five-Node Networking Table Example LEGEND: Table Number = the identification number assigned to each array within the system. CO Group = the line group used to access each system. Co Group 00 = internal calls only. Extn Range = the extension numbering range for the array. Ext BLF Slot = identifies PRIB slot locations in the Hub that are associated with each Node within the network, other than the Node being defined by the Table Number row. This allows DSS/BLF updates to be sent to the correct systems within the network. Node systems do not identify Ext BLF Slot locations because the Hub system controls passing of information. System 2 (Node) Ext 2000 - 2999 PRIB Slot 1 CO Group 01 Table NumberCO GroupExtn RangeExt BLF Slot 01 00 2000-2999 NA 02 02 1000-6999 NA 03 00 1000-8999 NA System 3 (Node) Ext 3000 - 3999 PRIB Slot 1 CO Group 01 Table NumberCO GroupExtn RangeExt BLF Slot 01 00 3000-3999 NA 02 02 1000-6999 NA 03 00 1000-8999 NA System 5 (Node) Ext 5000 - 5999 PRIB Slot 1 CO Group 01 Table NumberCO GroupExtn RangeExt BLF Slot 01 00 5000-5999 NA 02 02 1000-6999 NA 03 00 1000-8999 NA System 6 (Node) Ext 6000 - 6999 PRIB Slot 1 CO Group 01 Table NumberCO GroupExtn RangeExt BLF Slot 01 00 6000-6999 NA 02 02 1000-6999 NA 03 00 1000-8999 NA System 1 (Hub) Ext 1000 - 1999 PRIB Slot 1, CO Group 02 PRIB Slot 2, CO Group 03 PRIB Slot 3, CO Group 04 PRIB Slot 4, CO Group 05 PRIB Slot 5, CO Group 06 Table NumberCO GroupExtn RangeExt BLF Slot 01 00 1000-1999 -- -- -- -- 02 02 2000-2999 2 3 4 5 03 03 3000-3999 1 3 4 5 04 04 4000-4999 1 2 4 5 05 05 5000-5999 1 2 3 5 06 06 6000-6999 1 2 3 4 07 00 1000-8999 -- -- -- -- System 4 (Node) Ext 4000 - 4999 PRIB Slot 1 CO Group 01 Table NumberCO GroupExtn RangeExt BLF Slot 01 00 4000-4999 NA 02 02 1000-6999 NA 03 00 1000-8999 NA
C-18Programming Appendix C - Networking Systems Programming Steps 1. Press FLASH and dial [16]. The following message displays: 2. Select a valid table number (01-16), then press HOLD. The following message displays: 3. Press the desired button to select a trunk group, station range, external busy lamp field, and system number: [1] = Select Trunk Group (00-23), then press HOLD. [2] = Station Range – START (1000-8999), then press HOLD. [3] = Station Range – END (1000-8999), then press HOLD. [5] = External Busy Lamp Field (BLF)(1-28), followed by [1] to add or [0] to delete, then press HOLD. ( This button is for Hub programming only.) To add more than one BLF slot location, press the digit identifying the next slot location, followed by [1], then press HOLD. Repeat as necessary, until all slot locations are added. [6] = Status Check - press [0] to disable (default) or press [1] to enable. [22] = Page Up [23] = Page Down [24] = Returns you to Networking Tables display (shown in Step 1) Conditions » Feature access codes must not conflict with station numbering. » CO line numbers are fixed and cannot be changed other than the current FLASH 42 reassignment. » The VMID digits need to be programmed separately. » The SMDR will output up to 4-digit numbers in the station field. If less than 4 digits are selected in the numbering plan, leading spaces will be added in place of numbers. Call Accounting devices need to be configured to accept 4 digits. » When systems are tied together, each system has to have access to 911 through local lines. NET WORKING TABLES SELECT TBL NO TBL 01 ENTER BUTTON NUMBER Button #4 is an active button used for VoIP programming, but it is not used for network programming. The VoIP card cannot be used for networking applications.
ProgrammingC-19 Appendix C - Networking Systems Cabinet/Card Programming Description The Cabinet/Card Programming feature provides a means to assign the peripheral cards to alternative peripheral card slots. Flash 24 also allows for partial signaling over T1IBs (9) or PRIBs (8). For example, card slots ordinarily accommodate 24 CO line time slots each. This feature allows you to limit the amount of time slots per card to four (4), or multiples of four (4) up to 20. To use this feature, the card ID is programmed followed by the number of CO lines to be used in groups of four (4). A group of four (4) is known as a cluster. If the card number is programmed without a cluster number, all COs on that card are active. Programming Steps 1. Press FLASH and dial [24]. The following message displays: 2. Press the button corresponding to the desired cabinet. Button #17-19 represent cabinets 0-2. The following message displays: Button #1 LED is lit to indicate that you are programming for peripheral card slot 0. 3. Press the button corresponding to the desired slot location. (Buttons #1-9 indicate peripheral card slots 0-8.) 4. Enter a valid number for the type of card plugged into the current peripheral card slot. [00] = None [06] = GCOB [12] = VOIP [01] = ETIB [07] = DIDB [13] = SL12 [02] = DTIB [08] = PRIB [14] = LC08 [03] = DT24 [09] = T1IB [15] = LCI8 [04] = SLIB [10] = BRIB [16] = SI12 [05] = LCOB [11] = BR16 When using partial signaling, the last channel in the cluster and the 24th channel are data channels (e.g., for partial signaling with one cluster, the 4th and 24th channels are data channels. If two clusters are used, then the 8th and 24th channels are data channels.) CABINET 0 ENTER BUTTON NUMBER CAB X SLOT XX 00-12 DTIB Electrical bus configurations restrict the slots that can support T1 and PRI cards to slots 1-7 of Cabinet 0 and to slots 0-7 of Cabinets 1 and 2.
C-20Programming Appendix C - Networking Systems 5. Enter a valid number (1-5) to specify the desired cluster (partial) quantity. [1] = cluster of 4 [3] = cluster of 12 [5] = cluster of 20 [2] = cluster of 8 [4] = cluster of 16 No Entry = All CO lines 6. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 7. Press the reset button on the Main Processing Board (MPB). Ring Assignment Programming The local KSU will program ringing assignments by the fixed station number. For example, for CO line 1 to ring at station 100, use the sequence of Flash 40, 001001, HOLD, Page A, Button #10, dial 1007, HOLD. A remote system programs ringing assignments by the flexible station number. For example, for CO line 1 to ring at station 2000, use the sequence of 20007 + HOLD. Programming Steps 1. Press FLASH and dial [40]. The following message displays: 2. Enter a valid number for the range of lines being programmed. If only one line is being programmed, enter that number twice (e.g., 001 001). 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. Flexible button #19 (Page A) is lit. The following message displays to indicate current programming of that line or group of lines: XXX-XXX = CO Line Range 4. Press the RING ASSIGNMENT flexible button (FLASH 40, Page A, Button #10). The display shows the following information: A CO can only ring one remote device/extension at a time. CO LINE ATTRIBUTES SELECT A CO LINE RANGE If HOLD is pressed without entering a CO range, all CO lines are selected. XXX - XXX PAGE A ENTER BUTTON NUMBER RING ASSIGNMENTS ENTER DDDR The actual LCD displays a 3-digit destination field (DDD), but both a 3- or 4-digit entry is possible.
ProgrammingC-21 Appendix C - Networking Systems 5. Enter a valid Destination (DDD) or (DDDD) and Ring type (R) followed by the HOLD button (refer to Ta b l e C - 6 ). A confirmation tone sounds and the display updates. * Internal flexible numbers range = 100-8999 ** Remote device numbers can be any numbers between 1000-8999, excluding those numbers assigned for internal use. a For Remote Voice Mail Ring Assignment, refer to Flash 67. To add multiple stations: Enter: DDDDR HOLD DDDDR HOLD DDDDR HOLD...etc. (Example: 10073 HOLD, 10083 HOLD, 10093 HOLD) To delete a single station: Enter: DDDD0 HOLD (Example: 10080 HOLD) To delete multiple stations: Enter: DDDD0 HOLD DDDD0 HOLD...etc. (Example: 10080 HOLD, 10090 HOLD) Only one Node or the Hub can ring at any one time. Table C-6: CO Line Ringing Assignments Valid 3- and 4-Digit Destinations (DDD) and (DDDD) Valid Ring Types (R) System Speed Bins [9020–9999], for Off-Net Ringing [0] = No Ring; unassigned; or to delete a station Flexible Extension Numbers* [1] = Day Ring [D] Flexible Numbers for Voice Mail Groups 1–8* a[2] = Night Ring [N] Flexible Numbers for Hunt Groups 1–8* [3] = Day/Night Ring [DN] Flexible Numbers for Direct Ringing to Modem* [4] = Special Only [S] Flexible Numbers for ACD Groups 1–16* [5] = Day/Special [DS] Flexible Numbers for UCD Groups 1–8* [6] = Night/Special [NS] Remote Device Numbers** [7] = All Modes [Day/Night/Special [A]
C-22Programming Appendix C - Networking Systems Trunk Direction Programming CO Lines can be programmed on a per CO Line basis for the type of CO Line desired: Incoming, Outgoing, or Incoming and Outgoing. The 24th channel must be marked as Out-of-Service (OOS). This is true on all PRI cards, not just for networking. To eliminate collisions (referred to as “glare”), it is best to either: Divide CO Lines into Incoming or Outgoing lines, -or- Renumber the CO Lines on all of the Nodes to hunt in reverse order (refer to “Flash 42, Flexible Port Assignment”). Programming Steps 1. Press the TRUNK DIRECTION flexible button. (FLASH 40, Page A, Button #12). The following message displays: 2. Enter a valid number (0-3) on the dial pad which corresponds to the desired trunk type: [0] = Out-of-Service (OOS) [1] = Incoming Only [2] = Outgoing Only [3] = Both Incoming and Outgoing 3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. T-1 / ISDN Signaling Type Programming Description TIE signaling is used for networking systems. Programming Steps If the system is in the programming mode, continue using the program codes. If starting to program here, enter the programming mode. If Page B CO Line features must be changed: 1. Press FLASH and dial [40]. The following message displays: 2. Enter a valid number for the range of lines being programmed. If only one line is being programmed, enter that number twice (001 001). CO DIRECT ION 0-3 INCOMING - OUTGOING CO L IN E AT TRIBUTES SELECT A CO LINE RANGE If HOLD is pressed without entering a CO range, ALL CO lines are selected.