Vodavi Starplus Hybrid Key Telephone System Installation Manual

							TARPLUS 1428 CONFIGURATION NOTES 
NOTES: 
1. 
2. 
3. 
, 
4. 
5. 
6. 
7. 
8. 
9. 
10. 
11. 
12. 
13. The Expansion KSU, 2x4 Expander Module, 2x4 SLT Expander Module, and the 4x8 Expander Module 
each may have one additional DTMP Receiver Module installed on the module, this yields a maximum 
system capacity of 4. 
The Basic KSU, Expansion KSU, 2x4 Expander Module, 2x4 SLT Expander Module, and the 4x8 
Expander Module each have Green LED indicators for +5 Volts DC and -5 Volts DC. 
The Basic KSU, Expansion KSU, 2x4 Expander Module, and the 4x8 Expander Module each have Green 
LED indicators for +12 Volts DC (One per four Digital Key terminals). 
The 2x4 and 4x8 Expander Modules have an External Page Port, this yields a maximum system capacity 
of 4 external page zones. All External Page Zones Are I-Wav! The 2x4 SLT Expander Module 
provides NO External Page capability. 
All External Paging requires customer provided page amplifier, speakers and power supply for operation. 
If a 2x4 SLT Expander Module is installed in the system it requires a Ring Generator (Tellabs 8 101) be 
provided. 
If Off Premise Extension (OPX) Modules are installed a -48 Volt DC Power Supply is required. Each 
OPX module consumes 500ma of current. To arrive at a current rating for a power supply Multiply the 
Number of OPX Modules by 0.5, this will equal the current rating, in Amps, of the -48 Volt de power 
supply required. 
If Relay Closure is Required for any application, an optional Relay Sensor Module (RSM) is required. 
The unit provides three relays and three sensing circuits. Relays are rated at 24 Vdc, 1 amp and require 
customer provided power supply. 
Each OPX Module, RSM, or Digital Data Interface Unit requires one Digital Key Station Port for 
connection. 
Additional l/O ports may be added using the IOM (1 RS-232C DB25, 1 RS-422 RJ-14 ), 
If enhanced modem speed is required a 1200 Baud I . 
Modem Module may be added to the Basic KSU. 
The Basic KSU, Expansion KSU, 2x4 Expander 
Module, 2x4 SLT Expander Module, and the 4x8 
Expander Module each use RJ-11 Jacks for CO 
interface. The pinout is shown in the inset. 
1 A N 
liie!e 
Pin 8 1 (bhm) -N/C 
Pin 12 (b&k) . N/C 
Pin #S (rad) _ Ring 1 
Ph L4 (Qrren) -Tap ( 
G Pln#S (yallow) - N/C 
Pln M (brown) - N/C 
RJ-11 
If Loop Supervision is provided by telco, and Loop 
Supervision is enabled on a CO Line which is engaged ’ * 
in conversation with an SLT Port, and the outside party disconnects the call. A Loop Supervision signal 
of 700ms duration will be provided to the connected SLT or device. 
Page 3 1  
						

							STARPLUS 2856 CONFIGURATION 
COMPONENTS NECCESSARY FOR SYSTEM OPERATION 
Equipment Cabinet with Power Supply (KSU) 
Central Processing Board 
4x8 Key Station Interface Board QlJ 
4x8 SLT Interface Board 
ADDITIONAL SYSTEM COMPONENTS 
DTMF Receiver Module (RMJ 
1200 Baud Modem Module 
Expansion I/O Module 
EOUIPMENT CABINET WITH POWER SUPPLY 
ww 
POWER SUPPLY 
ON/OFF SWITCH 
EIGHT CARDSLOT BACKPLANE 
GROUNDING LUG 
FERRITEKIT 
5AMP 250 VAC SLO-BLOW FUSE 
CENTRAL PROCESSING BOARD 
PW 
300 BAUD MODEM 
BATTERY FOR BACK-UP OF RAM MEMORY (J3) 
RESET BUTTON 
SYSTEM HEARTBEAT INDICATION (RED LED) 
+ 5 VOLT DC AND -5VOLT DC INDICATIONS (GREEN LED@ 
MUSIC ON HOLD INPUT (RCA JACK) 
MUSIC ON HOLD ADJUSTMENT POT (R5) 
RS-2332C INPUT/OUTPUT PORT (RJ-45) 
NO DTMF RECEIVERS ON CPB 
- 
4x8 KEY INTERFACE BOARD 
(CW 
4 CO/CENTREX@BX LINES (LOOP START) 
EIGHT DIGITAL STATION PORTS 
1 EXTERNAL PAGE ZONE PER CARD (l-WAY) 
1 PROGRAMMABLE MULTI USE RELAY PER CARD 
RELAY STATUS LED INDICATOR 
CO LINE IN USE LED INDICATOR 
+ 5 VOLT DC AND -5VOLT DC INDICATIONS (GREEN LEDs) 
125 PAIR SHIELDED CABLE CURRENTLY PROVIDED 
Page 32  
						

							4x8 SLT INTERFACE BOARD 
(CW 
4 COICENTREXIPBX LINES (LOOP START) 
EIGHT STANDARD SINGLE LINE TELEPHONE (2500) PORTS 
w EXTERNAL PAGE ZONE 
1 PROGRAMMABLE MULTI USE RELAY PER CARD 
RELAY STATUS LED INDICATOR 
CO LINE IN USE LED INDICATOR 
+ 5 VOLT DC AND -5VOLT DC INDICATIONS (GREEN LEDs) 
125 PAIR SHIELDED CABLE CURRENTLY PROVIDED 
RING GENERATOR INPUT 
STANDARD MESSAGE WAlTING INDICATION 
DTMF RECEIVER MODULE 
uw 
PROVIDES ONE DTMF RECEIVER 
ONE MAY BE ADDED TO ANY 4X8 CARD 
REQUIRED FOR DISA 
REQUIRED FOR SINGLE LINE TELEPHONES 
ONE RECEIVER WILL SUPPORT EIGHT SLTs WITH LIGHT TO MODERATE TRAFFIC 
INCREASE RECEIVERS WHEN VOICE MAIL OR AUTO ATTENDANT IS INSTALLED 
NO DTMF RECEIVERS ARE PRESENT UNTIL YOU ADD THEM 
- 
EXPANSION I/O MODULE FOR THE 2856 
(IOW 
MOUNTS ON THE CPB 
1 RS-232C I/O PORT (RJ-45) 
1 RS-422 I/O PORT (RI-14) 
l PROGRAMABLE OPTIONS 
300, 1200,2400,4800,9600 BAUD 
1200 BAUD MODEM MODULE 
(MM) 
MOUNTS ON THE CPB 
PROVIDES ENHANCED MODEM SPEED OF 1200 BAUD 
Page 33  
						

							TARPLUS 2856 CONFIGURATION NOTES 
NOTES: 
1. 
2. 
3. 
4 4. 
5. 
6. 
7. 
-8. If the 4x8 SLT Interface Board (CSB) is used, at least one DTMF Receiver Module (RM) 
must be installed in the system. One module will support up to eight SLTs with light to 
moderate trafhc. 
If DISA is used at least one DTMF Receiver Module (RM) must be installed in the system. 
The 4x8 SLT Interface Board (CSB) requires a ring generator be used with the board, a 
Tellabs 8101,3OHz, 90 Vat Ring Generator may be used. Only one ring generator per system 
is required. 
When using more than one 4x8 SLT Interface Board (CSB) in a system, make sure that both 
ring generator cables have identical polarity. Use a DVM to continuity check the cables to 
identity proper polarity. 
The ferrite kit which comes with the KSU will support upto a 16x32 configuration (four 4x8 
Cards), beyond this configuration an additional ferrite kit must be used. 
The Ferrite kit must be properly installed to comply with FCC regulations (see installation 
manual for detatils). 
There are two RJ-14s located on the ’ 
front edge of each CKB and CSB they 
Pin # 1 (blue) -N/C 
are used to interface the CO Lines to 
the system. The Pinouts for the jacks Pin #3 (red) - Ring 1 
TANG 
Pin #4 (green) -Tip 1 
are shown in the inset . 
Installation of the battery strap (J3) on 
 FPin #2 (black) -Ring i 
L Ping6 (yellow) - Tip 2  - 
Pin 116 (brown) - N/C 
the CPB is required for proper system 
operation.  RJ-14 JACK 
9. 
10. 
11. If Off Premise Extension (OPX) Modules are installed, a -48 V DC Power Supply is required. 
Each OPX Module consumes 500ma of current. To arrive at a current rating for the power 
supply Multiply the Number of OPX Modules by 0.5, this will equal the current rating, in 
Amps, of the -48 volt DC power supply required. 
Each OPX Module, RSM, or Digital Data Interface unit requires one Digital Key Station Port 
for connection. 
IfLoop Supervision is provided by telco, and Loop Supervision is enabled on a CO Line 
which is engaged in conversation with an SLT Port, and the outside party disconnects the call. 
A Loop Supervision signal of 7OOms duration will be provided to the connected SLT or 
device. 
Page 34  
						

							STARPLUS DIGITAL SYSTEMS TERMINAL DEVICES 
DIGITAL TERMINAL DEVICES 
Enhanced Digital Terminal 
Executive Digital Display Terminal 
Basic Digital Terminal 
Digital Direct Station Selector/Direct Line Selector Console @SS/DLS) 
SLT Adapter/Off Premise Extension Module (OPX) 
Relay Sensor Module (RSM) 
Digital Data Interface Unit (DDIU) 
ADDITIONAL SYSTEM COMPONENTS 
Power Fail Transfer Unit (PFTU) 
EXECUTIVE DIGITAL DISPLAY TERMINAL 
34 BUTTONS 
48 CHARACTER LCD DISPLAY 
12 DIAL KEY PAD 
28 FLEXIBLE BUTTONS* 
ON/OFF BUTTON* 
MUTE BUTTON* 
SPEED BUTl-ON* 
FLASH BUlTON* 
TRANSFER BUTTON* 
HOLD BUTTON* 
SPEAKERPHONE 
SPEAKER VOLUME CONTROL 
RING VOLUME CONTROL 
H-T-P SWITCH 
DIRECTORY TRAY 
WALLMOUNTABLE 
K-STYLE HANDSET 
*EACH HAVE A SUPER BRIGHT LED 
Page 35  
						

							ENHANCED DIGITAL TERMINAL 
34 BUTTONS 
12 DIAL KEY PAD 
28 FLEXIBLE BUlTONS* 
ON/OFF BUTTON* 
MUTE BUTTON* 
SPEED BUTTON* 
FLASH BUlTON* 
TRANSFER BU’ITON* 
HOLD BU’lTON* 
SPEAKERPHONE 
SPEAKER VOLUME CONTROL 
RING VOLUME CONTROL 
H-T-P SWITCH 
DIRECTORY TRAY 
WALL MOUNTABLE 
K-STYLE HANDSET 
BASIC DIGITAL TERMINAL 
12 DIAL KEY PAD 
8 FLEXIBLE BUTTONS* 
ON/OFF BUlTON* 
MUTE BUlTON* 
SPEED BUTTON* 
FLASH BU+lTON* 
TRANSFER BUTTON* 
HOLD BU-ITON* 
HANDSFREE INTERCOM 
ON-HOOK MONITOR DIALING 
SPEAKER VOLUME CONTROL 
RING VOLUME CONTROL 
H-T-P SWITCH 
DIRECTORY TRAY 
WALLMOUNTABLE 
K-STYLE HANDSET 
*EACH HAVE A SUPER BRIGHT LED 
Page 36  
						

							DIGITAL DSWDLS CONSOLE 
48 BUTTONS 
EXPANDABLE TO 96 BUTTONS 
WALLMOUNTABLE 
EACH DSS/DLS REQUIRES A KEY STATION PORT FOR OPERATION 
’ THREE MAPPING OPTIONS 
MAP l* - FIRST 14 CO LINES, 28 STATIONS, FIRST THREE CALL 
PARR LOCATIONS, RELEASE, ATTENDANT OVERRIDE, AND ALL 
CALL PAGE BUTTON. 
MAP 2* - 28 CO LINES, FIRST 14 STATIONS, FIRST THREE CALL 
PARK LOCATIONS, ATTENDANT OVERRIDE, AND ALL CALL PAGE 
BUTTON 
MAP 3* - STATIONS 114-155, CALL PARR LOCATIONS 223-225, 
INTERNAL PAGE ZONES l-3 
*ALL BUTTONS EXCEPT CO LINE KEYS AND RELEASE KEYS ARE 
USER PRQG RAMMABLE. PROGRAMMTN G USER KEYS WHICH 
REQUIRE LAMFING ONTO A DSS/DLS CONSOLE IS NOTPERMITTED. 
SLT / OFF PREMISE EXTENSION MODULES 
Pw 
PROVIDES ONE LONG LOOP EXTENSION 
REQUIRES A -48 VOLT DC POWER SUPPLY 
INTERNALLY EQUIF’PED WITH A DTMF RECEIVER 
REQUIRES ONE DIGITAL TERMINAL PORT FOR OPERATION 
PROVIDES ONE POWER FAIL TRANSFER CIRCUIT 
RELAY SENSOR MODULE 
PROVIDES THREE Pt$.? R4MMABLE RELAYS 
l LOUD BELL CONTROL, CO LINE CONTROL CONTACTS, 
RAN START CONTACTS, PAGE RELAY, POWER FAIL 
CONTACT 
PROVIDES THREE SENSING CIRCUITS 
l RANSTOP 
REQUIRES ONE DIGITAL TERMINAL PORT FOR OPERATION 
REQUIRES EXTERNAL POWER SOURCE TO DRIVE 
I EQUIPMENT OPERATED BY RELAYS 
RELAY RATINGS ARE 24 VOLT DC, 1 AMP 
Page 37  
						

							DIGITAL DATA INTERFACE UNIT 
@DW 
POINT TO POINT INTERNAL DATA TRANSMISSION 
(DATA INTERCOM) 
APPLICATIONS 
l PRIWI’ER SHARING, MODEM SHARING, EXTENDING SMDR 
OUTPUT OVER 50 FEET FROM THE KSU, SMALL FILE 
TRANSFERS 
PROGRAMMABLE DATA RATES 
l 300,1200,2400,4800,9600,19.2K, 38.4K BAUD 
DB-25 FEMALE SERIAL PORT 
REQUIRES ONE DIGITAL TERMINAL PORT FOR OPERATION 
POWER FAIL TRANSFER UNIT 
(PFTU) 
12 TRANSFER CIRCUITS 
. WILL TRANSFER TIP AND RING OF TWELVE CO LINES TO 
TIP AND RING OF TWELVE SLT’s IN THE EVENT OF A POWER 
OUTAGE, CO ARE RESTORED TO THE SYSTEM WHEN 
POWERRETURNS 
REQUIRES 12 VOLT POWER SUPPLY FOR OPERATION 
TEST SWITCH 
Page 38  
						

							STARPLUS DIGITAL TERMINAL OPERATIONS 
OPERATIONS 
Flexible Button Programming 
H-T-P Switch 
Volume Controls 
FLEXIBLE BUTTON PROGRAMMING 
l 
IF YOU HAVE BU?TONS ON YOUR TELEPHONE WHICH HAVE NOT BEEN 
ASSIGNED IN DATABASE ADMINISTRATION PROGRAMMIN 
GASCOLINES,POO 
GROUP, OR LOOP BUTI-ONS, THEY MAY BE USER PROGRAMMED AT 
4  TELEPHONE AS A FEATURE OR SPEED DIAL BUTTON. IF THE BU-ITON WHICH YO 
WISH TO CHANGE IS DESIGNATED AS A CO LINE POOL OR LOOP BUlTON, 
MUST FIRST BE IMARKED 
AS A MULTI-FUNCTION Bu?TON IN DATABASE 
IUMINISTRATION PROGRAMMING. 
TO PROGRAM FLEXIBLE BUlTONS: 
1. PRESS THE SPEED BUTrON TWICE. 
2. PRESS THE ASSIGNED BUTTON TO BE PROGRAMMED. 
3. DIAL THE DESIRED FLEXIBLE By-TON PROGFWMMING CODE. 
4. PRESS THE ON/OFF KEY TO END OR REPEAT STEPS TWO AND 
THREE TO CONTINUE PROGRAMMIN 
G ADDITIONAL BUTT’ONS. 
TO ERASE FLEXlBLE BUTI’ONS: 
I. PRESS THE SPEED BUTrON TWICE. 
2. PRESS THE BU-ITON TO BE ERASED. 
3. PRESS THE RASH BUITON. 
4. PRESS THE ON/OFF KEY TO END. 
I FLEXIBLE BUTTON PROG 
RAMMING CODES 
I 
loo-155 
2Wl 228 
33lw 
4wl 
55wl 
566 
567 
571 
572 55[vl 
573 
574 
575 
576 55[vl 
577 55[vl 
601 
602 
603 
604 
620 
621 
623 
624 
625 
626 
627 
628 
631 
632 
633[22] 
633 00 STATION INTERCOM NUMBERS 
CALL PARK LOCATION (sy&m) 
PERSONAL PARK 
HUNT GROUP PILOT NUMBERS O-7 
VOICE MAIL GROUP PILOT NUhiBERS O-7 
ACDNCD GROUP PILOT NUMBERS O-7 
ACD/‘UCD AVAILABLE’UNAVAILABLE 
ACDAJCD CALLS IN QUEUE DISPLAY 
ACD AGENT LOGGUT 
ACD AGENT LOGIN 
ACD GROUP MEMBER STATUS 
ACD AGENT HELP 
ACD SUPERVISOR LOGOUT 
ACD SUPERVISOR UJGIN 
ACD SUPERVISOR QUEUE STATUS 
ATIXNDANT OVERRIDE 
ATTENDANT DISABLE CO LINE ACCESS 
CO LINE OFF-NET FORWARD 
NIGHT SERVICE 
CAMP43N 
LINE QUEUE 
MESSAGE WAIT 
CONFEIiENCE 
FXECUTIVE OVERRIDE 
LC!t LINE QUEUE CANCEL 
ACCOUNT CODE ENTER 
OHVO 
DO NOT DISTURB 
BACKGROUND MUSIC 
PERSONALIZED MESSAGES 
CLEAR PERSONALIZED MESSAGES 634 
635 
640 
695 
70 
71 
72 
73 
74 
75 
760 
76[01 
76iPl 
77 
9 
Ml HEADSET MODE 
k-l 
ICLID DISPLAY (UNANSWERED CALLS) 
ALL CALL FORWARD 
DISTINCTIVE RING 
i 
ALL CALL PAGE (INTERNAL & EXTERNAL 
INTERNAL PAGE ZONE 1 
INTERNAL PAGE ZONE 2 
INTERNAL PAGE ZONE 3 
INTERNAL PAGE ZONE 4 
INTERNAL ALL CALL PAGE 
EXTERNAL ALL CALL PAGE 
EXTERNAL PAGE ZONE 1-7 ’ 
EXTERNAL PAGE 1-7 
MEET-ME PAGE ANSWER 
LEAST COST ROUTING ACCES 
GROUP CALL PICK-UP 0 $ 
1/1 (i” 
;iPEEDl YY UNIVERSAL NIGHT ANSWER (UNA) . 
SPEED DIAL ACCESS 
l+ 
(STATION 00-19) (20-99 SYSTEM) 
[SPEED]+[*] SAVE NUh4BER REDIAL 
[SPEED]+[#] LAST NUMBER REDIAL 
YY = SPEED DIAL BIN NUMBERS 
ZZ = PERSONALIZED MESSAGES 
U = UCD/ACD GROUP NUMBER O-7 
C = CALL PARK LAXATION O-7 
H = HUNT GROUP NUMBER O-7 
V = VOICE MAIL GROUP NUMBER O-7 
P = EXTERNAL PAGE ZONE NUMBER 1-7  
						

							H-T-P SWITCH 
l 
USERS MAY SELECT THE METHOD BY WHICH THEY RECEIVE 
INTERCOM CALLS AND SIGNALS. 
OPERATION 
l HANDSFREE (H) (LEFT POSITION ) - THE STATION USER, UPON 
HEARING A TONE BURST AND A VOICE ANNOUNCEMENT MAY 
REPLY HANDSFREE. 
l TONE RINGING (T) (CENTER l%XITION) - A STANDARD TONE RING 
NOTIFIES THE PARTY OF AN INCOMING INTERCOM CALL. THE 
CALLED PARTY ANSWERS BY LIFTING THE HANDSET OR MOVING 
THE SWITCH TO THE HANDSFREE PQSITION OR PRESSING THE 
ON/OFF BUTTON. 
l PRIVACY (P) (RIGHT POSITION) - THE STATION USER RECEIVES A 
BURST OF TONE AND A VOICE ANNOUNCEMENT OVER THE 
SPEAKER THE MICROPHONE IS DEACTIVATED FOR PRIVACY. THE 
CALLED PARTY MUST LIFT THE HANDSET OR PRESS THE MUTE 
BUTTON TO REPLY. 
I 
AN OVERRIDE OF THE H AND P SWITCH POSITIONS IS PROVIDED FOR 
VOICE MAIL OR AUTO ATTENDANT TRANSFERS. TONE MODE 
RINGING BY BE FORCED BY DIALING 6# AND THE CALLED PARTIES 
EXTENSION NUMBER 
VOLUME CONTROLS 
l 
SEPARATE SLIDE SWITCHES ARE LOCATED ON THE FRONT OF 
THE DIGITAL TERMINALS TO CONTROL THE VOLUME OF VOICE AND 
TONE SIGNALS PRESENTED TO THE TERMINAL SPEAKER 
l THE SPEAKER VOLUME CONTROLS ALL VOICE SIGNALS 
PRESENTED TO THE SPEAKER I.E. SPEAKERPHONE CONVERSATION, 
BACKGRGUND MUSIC, AND PAGE ANNOUNCEMENTS. 
l THE RINGING VOLUME CONTROLS ALL TONE SIGNALS 
PRESENTED TO THE SPEAKER I.E. RINGING, CAMP-ON. MUTED 
RINGING WILL BE PROPORTIONATELY QUIETER THAN NORMAL 
RINGING, BASED ON THE SWITCH SETTING. 
Page 40