Vodavi Starplus Hybrid Key Telephone System Installation Manual

							STAFIPLUS~ Digital Systems TF NO: 43 
VOICE MAIL GROUPS (Cont’d) 
A Uave” Mall Index Entry 
Desaiptbm 
The “Leave” mail index specifies the outpulsing Table where the ‘in-band” digits required to connect a caller, 
forwarded into Voice Mall, to the called stations mail box are stored. Refer to Sec. 645.2 for programming entries 
into an outpulsing table. 
.._ 
To delete a ‘Leave” mail index entry, enter one pound [#] in the desired location on the keypad and press the 
HOLD button.(i.e.: Tables-l ,2,3 entered. To delete only Table 2, enter 1,#,3 and press HOLD). 
OpeIMOIX 
None 
Programming: 
To specify the “Leave” mail index (outpulsing table) to be accessed by a Voice Mail group: 
1. Press the LEAVE flexible button (Button #lo). 
2. Enter the three-digit “Leave” mail index on the dial pad. 
- 1st Digit = Standard Leave Table number (O-7). 
- 2nd Digit = Leave Table to utilize when station is forwarded to VM in a “No-Answer” condition. 
- 3rd Digit = Leave Table to utilize when station is forwarded to VM in a “Busy” condition. 
3. Press the HOLD button to save the entry. 
Confirmation tone is heard and the display will now update. 
Vodavi Communicalions Systems 
Page 56 d 56 TF NO. 43 
8300 E. Raintree Drive swttedaie, AZ 85260 (@a 443-6m  
						

							TECHNICAL FACT NOTICE 
Starplus Dlgltal Systems 
-TF NO: 33 
2/l/93 
2x4 SLT Expander Module 
Description: 
The 2x4 SLT Expander Module is a two CO by four single line telephone Interface module that plugs onto the main 
key service board of the Basic KSU or the main key service board of the Expansion KSU through the use of two 
ribbon cables. This module is a combination board that contains the necessary circuitry to connect two 
CO/Centrex/PBX loop start lines and four single line telephones to the system. This card also contains a connector 
for adding one application module (i.e. DTMF Receiver) to the system. 
Message Waiting capability comes installed on the 2x4 SLT Expander Module. This circuitry provides message 
waiting voltage to single line telephones equipped with message waiting lamps, and supports up to four single line 
telephones message waiting lamps at 9OV dc typically across tip and ring. 
LEDs & Indicators: Two green LEDs indicate the presence of +5V & -5V dc. An extinguished LED indicates the 
absence of the associated voltage. 
CO Llne/Statlon Interfaces: The 2x4 SLT Expander Module provides the interface for two Central Office, Centrex 
or PBX loop start, lines. The protection circuitry necessary to allow the system to be classified as a fully protected 
system are located on the card for each CO circuit. The CO circuits are equipped with current sensing circuitry that 
identifies distant end disconnect (loop supervision). The module design also provides proper fusing or protection 
to comply with the requirements of UL 1459 Second Edition and CSA C22.2 No. 225 standards. CO lines are 
connected to the system via RJ-11 modular connectors mounted on the bottom edge of the board. 
The 2x4 SLT Expander module also provides the interface for four standard on-premise single line telephones 
(2500 type). Four 36V dc single line circuits are provided on the printed circuit board. These single line telephones 
can be equipped with a standard message waiting lamp (9OV T&R) that operate on the “tip” and “ring” leads. 
Additionally, each circuit may be individually optioned (software controlled) to provide a loop interrupt 
to the 
connected SLT or device. The card will support single line telephones up to 2000 feet from the Basic KSU. 
On-premise single line telephones should present a load to the port totaling a maximum ringer equivalence of 2.5. 
A molex connector (J4) is located on the 2x4 SLT Expander Module to provide ring generator capabilities. It is 
recommended that the Tellabs 8101, 30 Hz, SOVAC Ring Generator be used with this board. 
Vodavi Communications Systems 
Page1 of 11 
6300 E. Raintree Drive Scottsdale, AZ 85260 
TF NO. 33 
(602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL SYSTEMS 
2 X 4 SLT EXPANDER MODULES (cont’d) 
CO Lines Connections: 
CO Lines are connected to the system via modular RJ-11 connectors mounted on the 
2x4 SLT Expander Module and accessed on the bottom of the Basic KSU. The 2x4 SLT Expander Module connects 
CO Line ports 5 and 6 (when installed on the Basic KSU) or ports 13 and 74 (when installed in the Expansion KSU) 
to the system through modular connectors J21 and J22 respectively. The pinouts of the modular connector are as 
follows. 
CO1 TIP 1 1 CO1 RING 
Figure 1 - CO 
Lines Connectlons 
NOTE: Currently ALL CO Line modular cables must pass through a 1.2” thick,, 2-3/a” diameter,, round ferrite core 
fhree times prior to exiting the KSU in order to comply with FCC regulations. Up to five cables can be wrapped 
Gd one ferrite core. 
*If the 2x4 Station or SLT Expander Module is NOT installed in the Basic KSU and an Expansion 
KSU is part of the system configuration, CO Ports 5-6 and Station Ports 9-12 can be re-assigned 
Refer to Techfact Notice #TFN 27A for Flexible Port Assignment features. 
Statlons Connectlons: The station ports of the 2x4 SLT Expander Module are wired to the main distribution frame 
via a 25pair, (50-pin) male amphenol-type connector located on the main key service board or expansion key 
service board, connector Jl 1. A 25-pair cable with a 50-pin female amphenol-type connector is required to extend 
the station ports to the main distribution frame. The pinouts for the stations on the 2x4 SLT Expander Module 
activate ports 009 through 012 on connector Jl 1 as shown in Table 1 when installed on the main key service board 
in the Basic KSU. Also refer to Table 1 Basic KSU Jl 1 Station Connections. 
Page 2 of 11 TF NO. 33 
Vodavi Communications Systems 8300 E. Raintree Drive Scottsdale, AZ 65260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL SYSTEMS 
Table 1 - 2 x 4 SLT Expander Module Jll BKSU Connections 
PAIR 
17 
18 
19 
20 
21 
22 
23 
.24 
25 PIN COLOR 
42 YUOR 
17 
OFvfL 
43 YIJGN 
18 GNNL 
44 YUBN 
19 BNNL 
45 YUSL 
20 SINL 
46 VI/BL 
21 BWI 
47 VI/OR 
22 OFVVI 
48 VI/GN 
23 GNNI 
49 VI/BN 
24 BNNI 
50 VIISL 
25 SWI DESIG 
Port 009 SLT Tip 
SLT Ring 
Port 010 SLT Tip 
SLT Ring 
Port 011 SLT Tip 
SLT Ring 
Port 012 SLT Tip 
SLT Ring 
External Page Tip 
External Page Ring 
Page3of 11 TF NO. 33 
Vodavi Communications Systems 8300 E. Raintree Drive Scottsdale, AZ 86260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE 
STARPLUS DIGITAL SYSTEMS 
2 x 4 SLT EXPANDER MODULE (cont’d) 
The pinouts for the stations on the 2x4 SLT Expander Module activate ports 025 through 028 on connector Jl 1 
are shown in Table 2 2x4 SLT Expander Module Jl 1 EKSU Connections when installed on the main key service 
board in the Expansion KSU. Also refer to Table 2 Expansion KSU Jll Station Connections. Only the Xmit Tip (SLT 
Tip) and Xmit Ring (SLT Ring) leads are used when connecting SLT stations to the 2x4 SLT Expansion Module. 
Table 2 - 2 x 4 SLT Expander Module Jll EKSU Connections 
PAIR 
I PIN 
I COLOR 
I DESIG 
17 
18 
19 
20 
21 
22 
23 
24 
25 42 
17 
43 
18 
44 
19 
45 
20 
46 
21 
47 
22 
48 
23 
49 
24 
50 
25 YUOR 
OR/YL 
YUGN 
GNNL 
YUBN 
BNNL 
YUSL 
SlNL 
VIn3L 
BWI 
O&l 
VI/GN 
GNNI 
VI/BN 
BNNI 
VIISL 
SWI Port 021 SLT Tip 
SLT Ring 
Port 022 SLT Tip 
SLT Ring 
Port 023 SLT Tip 
SLT Ring 
Port 024 SLT Tip 
SLT Ring 
External Page Tip 
External Page Ring 
Appllcatlon Module(s) Connections: The Ji connector on the 2x4 SLT Expander Module allows the installation 
of one application module (i.e. DTMF receiver) to the system. Refer to Application Module(s) Installation for a 
description of the available application modules. 
Vodavi Communications Systems 
Page4of 11 
8300 E. Raintree Drive Scottsdale, AZ 85260 
TF NO. 33 
(602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE 
STARPLUS DIGITAL SYSTEMS 
Installation: 
1. 
2. Remove power from both the Basic KSU and Expansion KSU, if installed. 
Locate the Meaage Waiting Module and remove the two screws holding it to the 2x4 SLT Expander 
Module. Remove the Message Wafting Module to expose the hold down screw underneath. 
3. Locate the J9 connector on the main service board of the Basic KSU or main key service board of the 
Expansion KSU and the Pl connector on the 2x4 SLT Expander Module. Refer to Figure 2 Basic KSU 
Application Card Locations. 
4. Gently push the cable from the Pl connector on the 2x4 SLT Expander Module onto the J9 connector on 
the main key service board of the Basic KSU or main key service board of the Expansion KSU. 
5. Locate the JlO connector on the main key service board of the Basic KSU or main key service board of 
the Expansion KSU and the P2 connector on the 2x4 SLT Expander Module. Refer to Figure 500-18 Basic 
KSU Application Card Locations. 
6. Gently push the cable from the P2 connector on the 2x4 SLT Expander Module onto the JlO connector 
on the main key service board of the Basic KSU or main key service board of the Expansion KSU. 
7. Secure the four screws attached to the 2x4 SLT Expander module to the main key service board of the 
Basic KSU or main key service board of the Expansion KSU. 
8. Re-install the Message Waiting Module and secure it with the two mounting screws. 
9. Restore power to both the Basic KSU and Expansion KSU, if installed. 
Page5of 11 TF NO. 33 
Vodavi Communications Systems 8300 E. Raintree Drive Scottsdale, AZ 85260 (602) 443-6000  
						

							J 
’ 
STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL SYSTEMS 
DSI 0 
DS2 0 
0 
1 
Pl 
_ _ _ _ _ _ - - - _ - 
Figure 2 - 2 x 4 SLT Expander Module 
Page6of 11 TF NO. 33 
Vodavi Communications Systems 8300 E. Raintree Drive Scottsdale, AZ 85260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE 
STARPLUS DIGITAL SYSTEMS 
4x8 SLT Interface Board (CSB) 
Description: 
The 4x8 SLT Interface Board (CSB) is a four CO Line by eight single line telephone interface board. The card is 
a combination card that contains the necessary circuitry to connect four CO/Centrex/PBX loop start lines and eight 
standard on-premise single line telephones (2500 type) to the system. This card also contains one additional voice 
(transmit) path for external paging and a connector for adding one application module (i.e. DTMF Receiver or Dual 
DTMF/Taik-Back Page Module) to the system. The 4x8 SLT interface Board can be removed or inserted with power 
on the KSU. Refer to Figure 5 Basic KSU Equipment Cabinet for component layout and location of connectors. 
A moiex connector is located on the 4x8 SLT Interface Board (CSB) to provide ring generator capabilities. It is 
recommended that the Teiiabs 8101, 30 Hz, SOVAC Ring Generator be used with this board. 
NOTE: Only one Ring Generator is required per system. At least one DTMF Receiver MUST be installed in the 
system. 
Message Waiting capability is installed onto the 4x8 SLT interface Board. This circuitry provides message waiting 
lamps to single line telephones equipped with message waiting lamps, and supports up to eight single line 
telephone Message Waiting lamps at 9OV ac typically across tip and ring. 
LEDs & indicators: Five red LEDs are located along the front edge of the 4x8 SLT interface Board, one for each 
CO Line to indicate when it is in use and one LED that monitors the contact operation of the multi use relay located 
on the board. Two green LEDs also located along the front edge of the 4x8 SLT Interface Board (CSB) indicate 
the presence of +5V & -5V dc. 
CO Line/Station Interfaces: The 4x8 SLT interface Board (CSB) provides the interface for four Central Office, 
Centrex or PBX loop start,, lines. The protection circuitry necessary to allow the system to be classified as a fully 
protected system are located on the card for each CO circuit. The CO circuits are equipped with current sensing 
circuitry that identifies distant end disconnect (loop supervision). The card also provides proper fusing or protection 
to comply with the requirements of UL 1459 Second Edition and CSA C22.2 No. 225 standards. The 4x8 SLT 
interface Board does not support data devices for data switching. 
The 4x8 SLT Interface Board (CSB) provides the control and interface for eight standard single line telephones 
(2500 type). Eight 36V dc single line circuits are provided on the printed circuit board. These single line telephones 
can be equipped with a standard Message Waiting Lamp (9OV T & R) that operate on the “tip” and “ring” leads. 
Additionally each circuit may be individually “optioned” (software controlled) to provide a loop interrupt to the 
connected SLT or device. The card will support single line telephones up to 2000 feet from the Basic KSU cabinet. 
On-premise single line telephones should present a load to the port totaling a maximum ringer equivalence of 2.5. 
Page7of 11 TF NO. 33 
Vodavi Communications Systems 6300 E. Raintree Drive Scottsdale, AZ 65260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE 
STARPLUS DIGITAL SYSTEMS a 
4 x 8 SLT EXPANDER MODULES (cont’d) 
. 
CO Lines Connections: CO Lines are connected to the system via modular RJ-14 connectors mounted to the 
front edge of the 4x8 SLT Interface Board and accessed through the bottom of the Basic KSU cabinet. Each 4x8 
SLT Interface Board connects four CO Line ports to the system through modular connectors J2 and J3 found on 
each card. The pinouts of the modular connector are as follows: 
4x8 SLT Interlace Board (CSS) W-14 Modular Jack Pinout 
Flgure 3 - 4 x 8 SLT Interface Board 
(CSB) RJ-14 Modular Jack Plnout 
NOTE: Currently ALL CO Line modular cables must pass through a 1.2” thick,, 2-3/8” diameter,, round ferrite core 
three times prior to exiting the KSU in order to comply with FCC regulations, Up to five cables can be wrapped 
around one ferrite core. 
c-tomour~ 
m 4X8 in- cd 
‘Q::.. 
“:::;; 
..:::., 
.: . ...:,, ‘7. 
b ..,:,, ‘.. 
hull RJ,,cj& .:.:.: .:...:,:,:., “‘” k”r*m~ 
m MOF 
Vodavi Communications Systems 
Page8of 11 
8300 E. Raintree Drive Scottsdale, AZ 85260 
TF NO. 33 
(602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL SYSTEMS 
0 
$ 
Station 
0 Connects 
Message 
Wait 
Circuitry 
(FUTURE) 
Optional- 
Dual DTMF/ 
Talk-Back Page 
Module 
_------- Jqg# ----------- 
Optional 
Single DTMF 
Receiver 
Module 
514 
I I 
CJJ Pin #1 (blue) - N/C 
1 Pin #2 (black) +f?i~@- 
1 
I 1 Pin #3 (red) - Ring I 
I 
I 
I 
C-5 1 Pin #4 (green) - Tip 1 
Pin #5 (yellow) Gp-% 
I 
Pin #6 (brown) - N/C 
4x8 SLT Interface Board RJ-14 Modular Jack Pinouts 
Figure 5 - 4 x 8 SLT Interface Board (CSB) 
Page 9 of 11 TF NO. 33 
Vodavi Communications Systems 8300 E. Raintree Drive Scottsdale, AZ 65260 (662) 443-6000