Vodavi Starplus Hybrid Key Telephone System Installation Manual

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL TELEPHONE 
TF NO: 27a 
‘ 
./ 
STATION RELOCATION FEATURE 
Description 
The Station Relocation Feature will provide a means to allow a user to unplug their station and plug it in at another 
location. Then by dialing a simple code followed by his old station number, bring all the station attributes including 
extension number, button mapping, speed dial, and class of service to the new location. 
Operation 
A station can be relocated by unplugging it and then plugging it in at a new location. Then dial [636] followed by 
the extension number of the station being relocated. Once this is done, all station attributes are copied to the 
current station. 
4 
NOTE: If a station is assigned to a specific port and that user unplugs their station and plugs it in at another 
location, the database administration programming will be updated to reflect the new port change. 
Conditions 
I. The station number that is dialed as the relocated station must be currently out of service. 
2. The relocated station will be given the station attributes of the station doing the relocating. The two stations 
have traded station numbers and station attributes. 
3. If a keyset is plugged into the relocated position it will have all the station attributes of the relocating station. 
4. This feature only is applicable to keysets. 
5. If a call is on hold at the relocating station or the relocated station is in service, error tone will be received. 
Vodavi Communications Systems 
Page 58 of 72 
6300 E. Raintree Drive Scottsdale, AZ 66260 /602) 443-6000 
TF NO. 27a  
						

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL TELEPHONE 
TF NO: 27a 
FLEXIBLE PORT ASSIGNMENT FEATURE 
Description 
The Flexible Port Assignment Feature will provide a means to assign stations and CO line numbers to any station 
or CO line port in the system. This provides complete flexibility in determining station and CO line numbers within 
the system as long as they stay within the system numbering plan. Therefore, a station can be assigned any 
number between 100 and 155 on a 2856 system and any station number between 100 and 127 on a 1428 system. 
A CO line can be assigned any number between 01 and 28 on a 2856 system and any CO Line number between 
01 and 14 on a 1428 system. This restriction is required to minimize memory requirements on the smaller system. 
Conditions 
1. All the station and CO Line numbers entered are stored in a temporary database area which is uploaded 
to main database when the system is reset. 
2. System reset can be accomplished in ADMIN by entering “FLASH” 80, Button #20, and ‘HOLD”. 
3. Station and CO Line numbers are restricted to the system numbering plan. 
4. To return the stations and CO line back to their default condition, enter ‘FLASH” 80, Button #4 and press 
“HOLD”. 
5. To print the station and CO line port assignments, enter ‘FLASH” 85, Button #4 and press “HOLD”. 
Programming - CO 
If the CO Line numbers need to be relocated to different ports: 
a. Press FLASH and dial [42]. The following message is shown on the display phone: 
123456789012345678901234 
b. The buttons 1 through 7 indicate cards 1 through 7. When the relocation program is initially entered, Button 
#l will be lit indicating the user is programming the CO Line numbers on the first card (CO Ports 1 through 
4). The LCD will display the CO Line numbers presently assigned to the first 4 ports. 
To change the CO Line number assigned to any port: 
a. Dial the position number on the display (01 through 04), followed by the CO Line numbered desired. For 
example: if 0103 were dialed, the CO line number of the first entry on the display would be changed to 03. 
In addition, since 03 was shown as the third entry on the display, that entry would be blank (##). 
Page 59 of 72 TF NO. 27a 
Vodavi Communications Systems 8300 E. Raintree Drive Scottsdale, AZ 85260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL TELEPHONE 
TF NO: 27a 
FLEXIBLE PORT ASSIGNMENT (cont’d) 
To select another card in the system: 
a. Press the button associated with that card. For example, if button #3 were pressed (CO Ports 9 through 
12) the CO Line numbers assigned to the third card would be displayed. CO Line numbers on the third 
card are changed in the same manner by entering the position number (01 through 04), followed by the 
CO Line number desired. 
When all the CO line numbers desired have been programmed, the system will have to reset to update the data. 
This is done so that the programming of CO Lines can be done while the system is in use. 
4 LCD Display 
After dialing the CO Line flexible port programming code (FLASH 42), the ADMIN station will receive the following 
display: 
123456789012345678901234 
Programming 
- Station 
If the Station numbers need to be relocated to different ports: 
a. Press FLASH and dial [52]. The following message is shown on the display phone: 
423456789012345678901234 
b. The buttons 1 through 7 indicate cards 1 through 7. When the relocation program is initially entered, Button 
#l will be lit indicating the user is programming the station numbers on the first card (Station Ports 1 
through 8). The LCD will display the station numbers presently assigned to the first 8 ports. 
To change the Station number assigned to any port: 
a. Dial the position number on the display (01 through 08), followed by the Station number desired. For 
example: if 01105 were dialed, the station number of the first entry on the display would be changed to 
105. In addition, since 105 was shown as the sixth entry on the display, that entry would be blank (###). 
Page 60 of 72 
TF NO. 27a ” 
Vodavi Communications Systems 
6300 E. Raintree Drive 
Scottsdale, AZ 66260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL TELEPHONE 
TF NO: 27% 
FLEXIBLE PORT ASSIGNMENT (cont’d) 
To select another card in the system: 
a. Press the button associated with that card. For example, if button #3 were pressed (Station Ports 17 
through 24) the station numbers assigned to the third card would be displayed. Station numbers on the 
third card are changed in the same manner by entering the position number (01 through 08) followed by 
the station number desired. 
When all the station ntimbers desired have been programmed, the system will have to reset to update the data. 
This is done so that the programming of station numbers can be done while the system is in use. 
LCD Display 
After dialing the station flexible port programming code (FLASH 52), the ADMIN station will receive the following 
display: 
123456789012345678901234 
Page 61 of 72 TF NO. 27a 
Vodavi Communications Systems 8300 E. Raintree Drive Scottsdale, AZ 66260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE 
STARPLUS DIGITAL TELEPHONE 
TF NO: 27a 
, 
HARDWARE FEATURES 
Digital Data Interface Unit (DDIU) 
Keyset Self Test 
Page 62 of 72 
TF NO. 27a 
Vodavi Communications Systems 8300 E. Raintrw Drive 
Scottsdale, AZ 85260 
(602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE 
STARPLUS DIGITAL TELEPHONE 
TF NO: 27a 
DIGITAL DATA INTERFACE UNIT (DDIU) 
Description 
The Data Feature is a time division switched, point to point data transmission capability which permits simultaneous 
voice and data communications (same system but not same port). The Data Feature offers the ability to transmit 
data information between personal computers, printers, plotters, modems, CRT terminals, and main frame computer 
ports. To establish a Data call a Digital Data Interface Unit (DDIU) is required to be connected to each data 
communications device. Data information can be switched through the system at speeds of 300, 1200,2400,4800, 
9600, 19.2K and 38.4K baud asynchronous. 
Installation 
The Digital Data Interface Unit (DDIU) is wired to the Stat-plus 1428 and Starplus 2856 like a digital telephone, and 
requires one station port. 
All connections to the DDIU are made on the back panel. The back panel has a modular jack and a DB-25 type 
connector. The modular jack, labeled KSU, is used to connect the DDIU to the station port of the system. The DB- 
25 connector supports an W-232 connection and is used to connect the data device to the system. 
A green LED lights to indicate the DDIU is properly wired to the system. 
Page 63 of 72 TF NO. 27a 
Vodavi 
Communications Systems 6300 E. Raintrw Drive Scottsdale, AZ 66260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE 
STARPLUS DIGITAL TELEPHONE 
- 
TF NO: 27a 
DIGITAL DATA INTERFACE UNIT (DDIU) (cont’d) .a’ 
l-r 
g MDF 
RR 
STATION 
~~CW&CTING 
1 KSU 
Figure 2 - Digital Data Interface Wiring 
Page 64 of 72 
TF NO. 27a 
Vodavi Communications Systems 8300 E. Raintree Drive 
Scottsdale, AZ 85260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE 
STARPLUS DIGITAL TELEPHONE 
TF NO: 27a 
DIGITAL DATA INTERFACE UNIT (DDIU) (Cont’d) 
Connection of the individual data communication devices requires that the installer be familiar with 
data 
communications terms, and has access to the appropriate information for connecting the variety of data 
communications devices that may be encountered. This information consists of, but is not limited to: 
1. Is the device configured as data terminal equipment (DTE), or data communications equipment (DCE). 
2. What pin on the RS-232 type connector performs what function? 
3. What signal leads are required to make the device operate? 
When planning the installation of the data feature, use a digital display phone at any location that is to originate 
a data connection. A DDIU can only be called; it cannot originate a connection. A digital display phone would 
typically be connected to a CRT terminal, or personal computer. A DDIU would typically be connected to a printer, 
or a MODEM. 
The station wiring for a digital display phone and a DDIU are identical. 
The data connector of the Digital Data Interface Unit (DDIU) is a 25 pin, type D connector which is configured as 
Data Communications Equipment with the following pin configurations. 
Pin Use 
2 Receive Data 
3 Transmit Data 
4 Request To Send 
5 Clear To Send 
6 Data Set Ready 
7 Signal Ground 
8 Data Carrier Detect 
11 
unassigned 
92 
Secondary DCD 
15 Transmit Clock 
17 
Receive Clock 
19 
Secondary RTS 
20 Data Terminal Ready 
22 Ring Indicator Direction 
into telephone (or DDIU) 
out of telephone (or DDIU) 
into telephone (or DDIU) 
out of telephone (or DDIU) 
out of telephone (or DDIU) 
out of telephone (or DDIU) 
into telephone (or DDIU) 
out of telephone (or DDIU) 
out of telephone (or DDIU) 
out of telephone (or DDIU) 
into telephone (or DDIU) 
into telephone (or DDIU) 
out of telephone (or DDIU) 
Page 65 of 72 TF NO. 27a 
Vodavi Communications Systems 6300 E. Raintree Drive 
Scottsdale, AZ 66260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL TELEPHONE _ 
TF NO: 27a 
DIGITAL DATA INTERFACE UNIT (DDIU) (cont’d) 
The following diagram will aid in the design of cables to connect the many different configurations of data 
communications devices. 
DCE 
DCE 
I I 
lxD 
RXD 
SIG ON 
RTS 
D-m 
DSFI 
DCD 
surs 
SDCD 
QM 
RI 
lxcu 
RXCLK 
slxl 3xD 
IXD 
SIG GND 
TTS 
3s 
l-m 
XR 
ICD 
Figure 3 - STARPLUS 1428 AND 2856 Data Switching 
Page 66 of 72 TF NO. 27a 
Vodavi Communications Systems 8300 E. Raintree Drive 
Scottsdale, AZ 85280 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTlCE STARPLUS DIGITAL TELEPHONE 
TF NO: 27a 
DIGITAL DATA INTERFACE UNIT (DDIU) (Cont’d) 
QNDI 
1 QND 
2Ro 
3lu 
sQ7 . 72Q 
ms4 
4RT2 
mJ3 
BLlco 
DlR2a 
2olnw 
me 
(IOSR 
iuP 
11 QM 
Figure 4 - MODEM to DDIU Cable 
Page 67 of 72 TF NO. 27a 
Vodavi Communications Systems 8300 E. Raintree Drive Scottsdale, AZ 85260 (602) 4436000