Vodavi Starplus Hybrid Key Telephone System Installation Manual

							LCR PROGRAMMING (Cont’d) 
L. Default LCR Data Base 
Programming Steps Description 
In an effort to decrease installation and set up time, 
usually associated with LCR, a default LCR data 
base has been incorporated. The default LCR data 
base will provide basic routing for local and long 
distance dialing. Default entries have been made in 
the Three Digit Table for local office codes (NNX’s) 
and all area codes (NPA’s). Two routes have been 
established with the default data base for routing of 
all calls under default. The entire default data base 
is shown in Table 665.7. 
The three digit tables contain a default where all 
Long distance (numbers requiring an area code) with 
a leading digit “1” are routed to Route table 00. 
Route Table 00 will route calls on lines in group 1 for 
all time periods. All Local calls (numbers that are 
dialed without an area code) with or without a leading 
digit “1’ are routed to route list table 01. Route list 
table 01 also routes calls using lines in line group 1 
for all time periods. 
655-l 2 Issue 1, November 1991  
						

							sTARPLUS@ SPD 1428 & 2856 
Digital Key Telephone Systems 
SECTION 660 
-  INITIALIZE DATA BASE PARAMETERS 
A. Introduction 
Programming Steps 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. (Refer to Sec. 600.2). 
If Data Base Parameters need to be initialized: 
1. Press FLASH and dial [80]. The following mes- 
sage will be shown on the display of a display 
phone: Description 
This section describes the procedures and steps 
necessary to initialize the system data base retum- 
ing any programmed data to its original or default 
value. The entire system data base may be initial- 
ized or various portions of the data base may be 
individually initialized. In addition to initialization of 
the entire data base, a system reset (Button 8) 
command is also included in this section for clearing 
meantime errors. 
The buttons on the programming terminal are de- 
fined as shown below when initializing or resetting 
the system data base. 
Issue 1, November 1991 660-l  
						

							Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2866 
Initialize Data Base Parameters 
B. Initialize System Parameters 
Programming Steps 
If System Parameters need to be initialized: 
1. Press the System Parameters flexible button 
(Button #l). The following message will be 
shown on the display phone: Description 
The system parameters may be initialized setting all 
data fields to their original, default values. The fol- 
lowing data fields are returned to their default values 
upon initializing the System parameters; 
2. To initialize the system parameters, press the 
HOLD button. Confirmation tone is heard. 
666-2 
Issue 1, November 1991  
						

							Initialize Data Base Parameters (Cont’d) 
Initialize System Parameters (Cont’d) 
, 
Programming Steps Description 
Issue 1, November 1991 660-3  
						

							Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2656 
Initialize Data Base Parameters (Cont’d) 
C. initialize CO Line Attributes 
Programming Steps 
If CO tine Attributes need to be initialized: 
1. Press the CO Line Attributes flexible button 
(Button #2). The following message will be 
shown on the display phone: Description 
The CO Line parameters may be initialized setting 
all data fields to their original, default values. The 
following data fields are returned to their default 
value upon initializing the CO Line parameters; 
2. To initialize the CO Line Attributes, press the 
HOLD button. Confirmation tone will be heard. 
DEFAULT VALUE 
660-4 
Issue 1, November 1991  
						

							sTARPLUS@ SPD 1428 & 2858 Digital Key Telephone Systems 
Initialize Data Base Parameters (Cont’d) 
D. Initialize Station Attributes 
Programming Steps 
If Station Attributes need to be initialized: 
1. Press the Station Attributes flexible button (But- 
ton #3). The following message will be shown 
on the display phone: Description 
The Station parameters may be initialized setting all 
data fields to their original, default values. The fol- 
lowing data fields are returned to their default value 
upon initializing the Station parameters; 
2. To initialize the Station Attributes, press the 
HOLD button. Confirmation tone will be heard. 
Off-Hook Preference 
Issue 1, November 1991 660-5  
						

							Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2868 
1 
ZAMP ON 
DND 
CONF 
HTP 
7, r SPKRVOL 
FUNGVOL 
Figure 660-l Default Button Mapping 
660-6 
Issue 1, November 1991  
						

							Initialize Data Base Parameters (Cont’d) 
E. Initialize Group Parameters 
Programming Steps 
If Group Parameters need to be initialized: 
1. Press the Group Parameters flexible button 
(Button #4). The following message will be 
shown on the display phone: Description 
Hunt, UCD and Voice Mail Group parameters may 
be initialized setting all data fields to their original, 
default values. The following data fields are returned 
to their default value upon initializing Group parame- 
ters: 
2. To initialize the Group parameters, press the 
HOLD button. Confirmation tone will be heard. 
PROGRAMCODE FLEX 
BUT-TON FEATURE DEFAULT VALUE 
(after initializing) 
FLASH 30 l-8 Hunt Groups 330337 
No Hunt Groups established 
9 Station or Pilot Hunting All Hunt Groups default using Pilot 
Hunting 
FLASH 60 1-8 UCD Groups 550-557 
No UCD groups established 
9 Alternate UCD Group Assign No UCD Alternates group 
assignments is made 
10 I Overflow Assignment 1 No Overflow assignment is made 
11 1 UCD Station Assignments 
No stations are assigned 
12 Announcement Table Assign 
No RAN tables are specified 
1 UCD Ring Timer 
060seconds 
2 UCD Message Interval Timer 
060 seconds 
3 
UCD Overflow Timer 060seconds 
4 UCD Wrap-Up Timer 
004seconds 
5 UCD No Answer Timer 
000 seconds (disabled) 
1-2 RAN Tables 1 and 2 
No RAN parameters set  FLASH 61 
FLASH 62 
FLASH 65 1-8 Voice Mail Groups 440447 No Voice Mail groups are 
established 
9 Alternate VM Group Assign No Alternate VM group assignmeni 
is made 
10 Leave Table No outpulsing table is 
referenced 
FLASH 66 11 Retrieve Table No outpulsing table is 
referenced 
12 VM Station Assignments 
NO stations are assigned 
l-7 Voice Mail Out-Pulsing Tables Out-pulse tables are empty 
for in-band signaling by default 
8 Voice Mail Disconnect Table Disconnect table is empty 
FLASH 67 1 In-Band Digits for Incoming 
CO Calls Disabled by default 
I 
Issue 1, November 1991 660-7  
						

							Initialize Data Base Parameters (Cont’d) 
F. Initialize Toll Tables 
Programming Steps 
If Exception Tables need to be initialized: 
1. Press the Toll Tables flexible button (Button 
#5). The following message will be shown on 
the display phone: Description 
The Toll Table parameters including the Allow/Deny 
Tables and the Special Tables may be initialized 
setting all tables to their original, default values. The 
following Tables are cleared returning to their default 
value upon initializing the Exception Tables parame- 
, 
2. To initialize the Toll Tables, press the HOLD 
button. Confirmation tone will be heard. 
TABLE DEFAULT VALUE 
(after initializing) 
ALLOW TABLE - A Table Cleared (no entries 
DENY TABLE - A Table Cleared (no entries) 
ALLOW TABLE - B Table Cleared (no entries) 
DENY TABLE - B Table Cleared (no entries) 
SPECIAL TABLE Table Cleared (no entries allowed, no 
1 area code specified) 
SPECIAL TABLE Table Cleared (no entries allowed, no 
2 area code specified) 
SPECIAL TABLE Table Cleared (no entries allowed, no 
3 area code specified) 
SPECIAL TABLE 
4 Table Cleared (no entries allowed) 
666-6 Issue 1, November 1991  
						

							STARPLUS@ SPD 1428 & 2856 Digital Key Telephone Systems 
Initialize Data Base Parameters (Cont’d) 
G. Initialize System Speed 
Programming Steps Description 
If System Speed bins need to be initialized: 
1. Press the System Speed flexible button (Button 
#6). The following message will be shown on 
the display phone: 
2. To initialize the System Speed bins, press the 
HOLD button. Confirmation tone will be heard. Numbers entered into the System Speed dial Table 
may be initialized clearing all bins to their original, 
default value (empty). All bins 20 through 99 are 
cleared returning to their default value (empty) upon 
initializing the Speed Dial Table. 
Issue 1, November 1991 660-9