Vodavi Starplus Hybrid Key Telephone System Installation Manual

							STARPLUS’ Digiil systems TF NO: 43 
PRIVACY RELEASE TONE OPTION 
Description: 
Privacy is insured on all communications in the system. If desired, the customer may elect to disable the Automatic 
Privacy feature, thus allowing up to three other stations to join in on an existing CO Line conversations. 
NOTE: Disabling of the privacy feature may be limited by federal, state or local law, so check the relevant laws in 
your area before disabling privacy. 
l Per CO Line Option: 
This feature allows each CO line to be individually programmed for privacy. This feature is useful for 
maintaining security on such lines as Data lines, Private lines, or special circuits requiring privacy. If privacy 
is disabled on 
a CO line then, while in use, another station may enter the conversation simply by pressing the 
CO line button. A programmable warning tone is presented to all parties prior to actual cut-thru. The station 
attempting to enter the conversation must also have privacy disabled. 
l Per Station Option 
Each station may be programmed to give the station the capability to join an existing conversation simply by 
pressing the CO line button that is in use. A programmable warning tone is presented to all parties when the 
station enters the conversation. The CO line must also have privacy disabled to allow the cut-thru. 
NOTE: Display stations will continue to receive the *CONFERENCE” display regardless of the warning tone setting. 
Programming: 
If the Privacy Release Tone needs to be changed: 
1. Press FLASH and dial [06]. The following message is shown on the display phone: 
2. Press the BARGE IN WARNING TONE flexible button (Button #l). The following message is shown on the 
display phone: 
3. Enter a one-digit value on the dial pad to enable or disable the conference tone. 
[0] = Disabling of Conference tone 
[1] = Enabling of Conference tone 
4. Press the HOLD button to save the entry. Confirmation tone is heard and the display will now update. 
Default By default, the Privacy Release Tone is enabled. 
Page 16 of 56 TF NO. 43 
Vodavi Ckmmunicalions Systems 8300 E. Raintree Drive !k.dtsdale, AZ 85260 @@) 44s6ooo  
						

							STARPLUS” Digiil SystemS TF NO: 43 
FLASH RATES (Programmable) 
Description: 
The flash rates for the following features can now be programmed to 16 different options in admin programming: 
47 
l Incoming CO line ringing: defaults to 30 ipm flash 
l Incoming intercom ringing: defaults to 120 ipm flutter 
l Call Forward: defaults to 30 ipm flash 
l Message Waiting: defaults to 15 ipm flash 
All other flash rates in the system are fixed at the rates shown in Table 400-13 DSS/BLF Button Visual Indicators, 
Table 400-14 CO Line. Button Visual Indicators, and Table 400-15 Function Button Visual Indicators in the Starplus 
Digital Systems Technical Manual, Issue 
1, November 1991. 
Programming: 
If the flash rates need to be changed: 
1. Press FLASH and dial [07]. The following message is shown on the display phone: 
The available flash rates are as follows: 
l oo=off 
l 01 = Steady On 
l 02 = 30 ipm flash 
l 03 = 60 ipm flash 
l 04 = 240 ipm double wink 
l 05 = 240 ipm flash 
l 06 = 240 ipm flutter 
l 07 = 460 ipm flash 
l 08 = 480 ipm flutter 
l 09 = 15 ipm flash 
l 10 = 120 ipm flash 
l 11 = 120 ipm flutter 
l 12 = 480 ipm wink 
l 13 = 240 ipm wink 
l 14 = 240 ipm quad wink 
l 15 = 480 ipm triple wink 
Vcdavi Communifzations Systems 
Page 17 of 56 TFNO. 43 
8300 E. Ftaintree Drive Scottsdale, AZ 85260 (602) 443-6ow  
						

							STARPLUS@ Digiii systems 
TF NO: 43 
Flash Rates (Cont’d) 
A banning CO Line Ringing: 
1, Press the INCOMING CO RINGING flexible button (Button #l). The following message is shown on the display 
phone: 
2. Enter a two-digit value on the dial pad to correspond to one of the 16 available options. 
3. Press the HOLD button to save the entry. Confirmation tone is heard and the display will now update. 
Default By default, the Incoming CO Ringing is set for a 30 ipm flash. 
B. incoming intercom Ringing: 
1. Press the INCOMING ICM RINGING flexible button (Button #2). The following message is shown on the display 
phone: 
2. Enter a two-digit value on the dial pad to correspond to one of the 16 available options. 
3. Press the HOLD button to save the entry. Confirmation tone is heard and the display will now update. 
Default By default, the Incoming Intercom Ringing is set for 120 ipm flutter. 
C. Call Fonvarding: 
1. Press the CALL FORWARD flexible button (Button #3). The following message is shown on the display phone: 
2. Enter a two-digit value on the dial pad to correspond to one of the 16 available options. 
3. Press the HOLD button to save the entry. Confirmation tone is heard and the display will now update. 
Defauk By default, the Call Forward is set for a 30 ipm flash. 
Page 18 of 56 TF NO. 43 
Vodavi Communications Systems 83&l E. Raintree Drive Scottsdale, AZ 65260 032) 443-woe  
						

							STARPLUS@ Digiil Systems 
TF NO: 43 
Flash Rates (Cont’d) 
D. Message Waiting: 
1. Press the MESSAGE WAITING flexible button (Button #4. The following message is shown on the display phone: 
2. Enter a two-digit value on the dial pad to correspond to one of the 16 available options. 
3. Press the HOLD button to save the entry. Confirmation tone is heard and the display will now update. 
Default: By default, the Message Waiting is set for a 15 ipm flash. 
Vodavi Communications Systems 
Page 19 of56 ?F NO. $3 
WI E. Raintree Drive Scottsdale, AZ 85260 w 44cwNJ  
						

							STARPLUS” Dig&d systems TF NO: 43 
CO LINE AlTRIBUTES 
DISA Programming Options (Button #7) 
Trunk Direction (Button #13) 
Ring Delay Timer (Button #14) 
Vodavi Communications Systems 8300 E. Raintrw Drive 
Page 20 of 56 
Scottsdale, AZ 85260 
TF NO. 43 
(602) 443aoo  
						

							STARPLUS” Digital Systems TF NO: 43 
DISA PROGRAMMING OPTIONS 
Description: 
A line can be assigned as a DISA line during night service only or on a 24- hour basis. Additionally, a DISA line 
is allowed to follow station forwarding during night service only or on a 24-hour basis. 
An unlimited number of DISA lines can be .programmed into the system. A DISA access code can also be 
programmed. Incoming DISA callers may dial any valid internal station or access outside line groups. A CO line 
ringing at a station will follow preset forward or no-answer call forward using the preset forward timer the same as 
an initially ringing CO call does. It will follow direct forward and busy forward the same as an initially ringing CO 
call. If the preset forward timer is set to 06, the first forward of the DISA ringing call at 
a station will take 15 
seconds. DISA callers-will be subjected to the Class of Service placed on the line accessed for outdialing. It is 
recommended that Loop Supervision be enabled when setting up DISA line(s). 
Refer to the following Sections in the Starplus Digital Technical Manual. Sec. 610.1, System Timers, 
Conference/DISA Timer allows the system administrator to control the length of time a DISA caller is allowed after 
establishing a “Trunk-to-Trunk” call. After expiration of the Conference Timer, a tone will be presented to both DISA 
parties, then one minute later the system will automatically release both trunks. The Conference Timer does not 
affect or control a DISA-to-Station call. 
Programming: 
If any CO line features are to be changed: 
1. Press FLASH and dial [40]. The following message is shown on the display phone: 
~~SELECT’A’~CO”UNE’RANGE ?:. ,.::‘:. 
2. Enter a four-digit number for the range of lines being programmed. If only one line is being programmed, enter 
that number twice (0101). 
3. Press the HOLD button to save the entry. Confirmation tone is heard and the display will now update. Flexible 
button #20 (New Range) will be lit. The following message is shown on the display phone to indicate current 
programming of that line or group of lines. 
Where: XX-XX = CO Line Range (01-46) 
DT = DTMF or Dial Pulse 
CO = Line Type, CO or PBX 
UNA = Universal Night Answer enabled 
C = DISAJTrk-to-Trk enabled 
P = Privacy feature enabled 
LSX = Loop Supervision 
DSX = Type of DISA options 
FLXX t Flash Timer; GRPX = CO Line Group 
COSX =CO Line Class of Service 
Vodavi Communications Spiwms 
Page 21 of 56 TF NO. 43 
83&l E. Rainlrse Drive ,sLcdtaa, A.2 Bmo (602) 443-6ooo  
						

							STARPLUS’ Digital Systems TF NO: 43 
DISA Programming Options (Cont’d) 
4. Press the DISA flexible button (Button #7). 
5. Enter a one-digit value on the dial pad to indicate type of DISA desired. 
[0] = No DISA (disable DISA) 
[l] = 24-Hour DISA 
[2] = Night DISA only 
[3] = 24-Hour DISA with forwarding 
[4] = Night DISA only with forwarding 
6. Press the HOLD button to save the entry. Confirmation tone is heard and the display will now update. 
Default By default, there are no outside lines assigned as DISA lines. 
Page 22 of 56 TF NO. 43 
Vodavi Communications Systems WO E. iiaintree Diva §izYdale, k 6250 WQ) 4434ooo  
						

							STARPLUS’ Digiil SyStemS TF NO: 43 
TRUNK DIRECTION 
Descriphkn: 
CO Lines can be programmed on a per CO tine basis for the type of CO Line desired: Incoming, Outgoing, or Both 
incoming and outgoing. 
l Incoming: Restricts the CO Line for incoming calls only: Users cannot press a CO line button or dial CO line 
access code to access a CO line. Users can answer a CO call and then transfer the call. Users can place call 
on hold, park the call, and other stations can pick-up the call. 
l Outgoing restricts the CO tine to outgoing calls only. Users can press a CO line button or dial CO line access 
code to access a CO line. Users can place call on hold, park the call, and other stations can pick-up the call. 
Incoming calls to this CO type are ignored. Callers receive ringback, no answer. 
l Both incoming and outgoing type allows calls to be received or dialed out. 
Programming: 
1. Press the TRUNK DIRECTION flexible button. (Button #13). The following message is shown on the display 
phone: 
2. Enter a one-digit value on the dial pad which corresponds to the desired trunk type: 
[0] = Out-of-Service (00s) 
[l] = Incoming only 
[2] = Outgoing only 
[3] = Both Incoming and Outgoing 
3. Press the HOLD button to save the entry. Confirmation tone is heard and the display will now update. 
Default By default, all CO lines default to both incoming & outgoing type. 
Page 23 of 56 TF NO. 43 
Vodavi Communications Systems 8300 E. Raintree Drive 
Sadtsdale, AZ 85260 w4 443-woe  
						

							STARPLUS” Dig&al Systems TF NO: 43 
RING DELAY TIMER 
Desuipth: 
The Ring Delay timer has been added to the Starplus Digital Systems to accommodate ICLID interface 
requirements. 
The Ring Delay timer is started whenever a CO Line detects incoming ringing. When the timer expires, CO line 
ringing will be detected by digital terminals and Single Line telephones. The purpose of this timer is to wait until 
after the first ring cycle to be detected by the digital system in order for ICLID information to be passed down the 
CO line prior to being answered. 
Programming: 
1. Press the RING DELAY TIMER flexible button (Button #14). The following message is shown on the display 
phone: 
2. Enter a two-digit timer value on the dial pad between 00-20 which corresponds to 00 seconds to 20 seconds. 
3. Press the HOLD button to save the entry. Confirmation tone is heard and the display will now update. 
Default By default, the Ring Delay timer is set at 00 (disabled) and is variable from 00 to 20 seconds. 
Page 24 of 56 TF NO. 43 
Vodavi Communications Systems 8300 E. Raintree Drive Scottsdale, AZ 85260  
						

							STARPLUS” Digiil Systems TF NO: 43 
STATION ATTRIBUTES 
CO Line Ringing Options 
, 
Vodavi Communications SystertIS 
Page 25 of 56 TF NO. 43 
8300 E. Raintrw Drive 
Scoltsdale, AZ 85260 W) 443-ml