Vodavi Starplus Hybrid Key Telephone System Installation Manual

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL TELEPHONE 
TF NO: 27a 
DIGITAL DATA INTERFACE UNIT (DDIU) (cont’d) 
Operation 
To establish a connection to any idle data port, a user with an associated DDIU dials the station number of the 
DDIU or the group access number of the groups that the DDIU has been inserted into or depresses a DSS button 
representing the DDIU. The key system will then determine the baud rate setting for the called DDIU and convert 
the users associated DDIU to the same baud rate. The system will then complete the connection. 
A second method to establish a connection between two DDIU is done by the first attendant. The first attendant 
dials the extension number of one data unit. Dial tone is received and the display will show the BAUD RATE. Then 
the first attendant dials the station number of the second data unit, confirmation tone is heard. This connection will 
, be maintained until the first attendant dials the station number of one DDIU followed by pressing the FLASH button. 
To break down an established connection the user should dial his associated DDIU number or depress the DSS 
button for the associated DDIU followed by depressing the ‘FLASH” button. 
A station user can configure his associated DDIU by: 
1. The station user dials the DDIU access code [63T] on the dial pad. 
2. Enter the three-digit extension number of the DDIU. The display will show the BAUD rate setting, 
the data length (8 or 9), and the number of stop bits (1 or 2). 
To change the baud rate: 
1. Press the “HOLD” button. Then enter the one-digit baud rate desired. Press the ‘SPEED’ button 
to save any changes made. 
1 = 300 
2 = 1200 
3 = 2400 
4 = 4800 
5 = 9600 
6 = 19.2K 
7 = 38.4K 
To change the character length: 
1. Press the “TFlAN’ button. Then enter the one-digit character length desired, either 8 or 9. Press 
the ‘SPEED’ button to save any changes made. 
To change the number of stop bits: 
1. Press the “MUTE” button. Then enter the one-digit stop bit desired. Press the ‘SPEED button save 
any changes made. 
Page 68 of 72 TF NO. 27a 
Vodavi Communications Systems 6300 E. Raintree Drive Scottsdale, AZ 66260 (602) 4436000  
						

							STARPLUS TECHNICAL FACT NOTlCE STARPLUS DIGITAL TELEPHONE 
TF NO: 27a 
DIGITAL DATA INTERFACE UNIT (DDIU) (Cont’d) 
Programming 
In ADMIN, enter station programming (Flash 50) Page B, Button #l and enter an ID of 7 followed by the associated 
station number or [##I#] in the case of a DDIU without an associated station. 
The Digital Data Interface Units (DDIU) in the system can be configured in ADMIN by: 
1. Press the FLASH button and dial (511 on the dial pad. 
2. Enter the three-digit extension number of the DDIU and depress the ‘HOLD” button. The display 
will show the present settings for the DDIU. 
To change the BAUD rate: 
1. Press the BAUD HATE flexible button (Button #I). 
2. Enter the one-digit baud rate desired. 
1 = 300 
2 = 1200 
3 = 2400 
4 = 4800 
5 = 9600 
6 = 19.2K 
7 = 38.4K 
3. Press the ‘HOLD’ button to save any changes made. 
To change the character length. 
1. Press the CHARACTER LENGTH flexible button (Button #2). 
2. Enter the one-digit character length desired, either 8 or 9. 
3. Press the ‘HOLD’ button to save any changes made. 
To change the stop bits: 
1. Press the STOP BIT flexible button (Button #3). 
2. Enter the one-digit stop bit desired. 
3. Press the HOLD button save any changes made. 
To select a different Data unit press button #20 and enter a new data unit station number. 
Page 69 of 72 TF NO. 27a 
Vodavi Communications Systems 6300 E. Raintree Drive 
Scottsdale, AZ 66260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL TELEPHONE 
TF NO: 27a 
DIGITAL DATA INTERFACE UNIT (DDIU) (Cont’d) 
Conditions 
1. The System is transparent to the devices being connected. Therefore each DDIU must be configured with 
a specific baud rate, number of data bits and number of stop bits. This configuration will be done by the 
first attendant or in the case of an associated data unit can be configured by the user. 
2. Data switching is accomplished using the same wiring the telephone station uses for voice switching. 
3. Data ports can be arranged in UCD Groups or Hunt Groups. 
4. 
I Data ports do not have to be associated with a keyset, however to connect two DDlU devices one of them 
must be associated with a keyset unless the connection is made by the first attendant. 
5. When the data connection has been completed, the baud rate used in the connection will be displayed on 
the keyset. 
6. Non associated DDIU connections can be broken down by the first attendant. 
7. A DDIU has a DCE interface. Therefore a straight through RS232 cable can be used connect to a DTE 
device (printer, PC, etc.). 
8. Each DDIU requires a digital terminal port. 
LCD Display 
A station after dialing an associated DDIU will receive the following display: 
123456789012345678901234 
A station after dialing the programming code will receive the following display: 
123456789012345678901234 
Page 70 of 72 TF NO. 27a 
Vodavi Communications Systems 6300 E. Raintree Drive Scottsdale, AZ 66260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL TELEPHONE 
TF NO: 27a 
KEYSETSELFTEST 
Description 
The Star-plus Digital Key Systems contain a test mode feature that supports the offline testing of Digital keysets and 
DSS units. The term offline means that the unit under test is disconnected from the switch during the test operation. 
Keysets not under test continue to operate in the normal manner. Tests are provided to verify the keyset and DSS 
LED, LCD, and keyboard button operations. 
Operation 
The test mode is entered by taking a keyset’s handset off hook and by dialing SPEED 7#. This keystroke sequence 
disconnects the keyset from the system and brings up the Test Mode Menu on the keyset’s LCD. The test mode 
is exited by putting the handset back on hook. This reconnects the keyset to the system. 
Test Mode Menu 
The menu allows the operator to select a test mode by pressing the mode number at the dial pad. 
Modes: 
1) Keyset LCD/LED Test 
2) Keyset Button Test 
3) DSS LED/Button Test 
The operator can always return to the main test menu by pressing ##. 
1) Keyset LCD/LED Test 
This test outputs a series of continuously repeated LCD string messages to LCD lines 1 and 2. The set of 
strings consists of the letters ‘A’ through ‘x’ and ‘a’ through ‘x’. The 
next set of strings are: 
‘PICKUP TRUCK SPEED ZONE!” 
I*** 
STANDING BACK ***” 
The strings are alternately displayed on lines 1 and 2 of the LCD display. 
In addition all the LEDs are flashed at the rate of 15 IPM. 
2) Keyset BUTTON Test 
a) Pressing a keyset key turns on the LED and displays and LCD message identifying the key 
number. In addition switching the HTP switch from one position to another will cause the 
letter ‘H-POS’, ‘T-POS”, or ‘P-POS” to be displayed. 
b) Pressing dial pad keys displays an LCD message that indicates which digit was pressed. 
cl LEDs can be tested independently of the KEYS by pressing the flex LED number at the 
dial pad. For example, LED 10 is turned on by pressing dial pad digits ‘1” “0”. As each 
set of new numbers is entered the previously lit LED is turned off and the new LED is 
Page 71 of 72 
TF NO. 27a 
Vodavi Communications Systems 6300 E. Raintree Drive 
Scottsdale, AZ 85260 (602) 443-6000  
						

							STARPLUS TECHNICAL FACT NOTICE STARPLUS DIGITAL TELEPHONE ., 
TF NO: 27a 
turned on. Invalid flex values (ex. 00,99) turn off currently lit LED. 
3) DSS LED/BUTTON Test 
When the DSS test is selected and a DSS test is invoked ALL DSSs associated with the keyset running 
the test are placed in test mode. If no DSS unit is associated wit the keyset, the keyset display will indicate 
“NO DSS’. The DSS LED test will cause all the LEDs to flash at a 15 IPM rate. Once started the DSS LED 
test will continue until a DSS flex button is depressed. Pressing a DSS flex button turns on the flex key LED 
and displays an LCD message on the associated keyset identifying the flex key number (01 to 48). In 
addition, it turns off the previously selected flex LED. 
Conditions 
4 1. Test mode disrupts the normal operation of a keyset or DSS. 
LCD Display: 
The Main Test mode menu is as follows: 
123456789012345678901234 
The Keyset BUTTON Test mode menu is as follows: 
123456789012345678901234 
The DSS BUTTON Test mode menu is as follows: 
123456789012345678901234 
Page 72 of 72 TF NO. 27a 
Vodavi Communications SyStemS 8300 E. Raintree Drive 
Scottsdale, AZ 85260 (602) 443-6000  
						

							TECHNICAL FACT NOTICE 
sTARPLUS D@ftal Systems 
TF NO: 43 
2/17&I 
ADDITIONAL FEATURES - STARPLUS@ SPD 1428/2856 Digital Systems 
Issue 1, November 1991 
A Key Station Features matrix is included in this techfact to identify the new software packages for the Stat-plus 
Digital Systems. The following list of new features are available with software version 2.3 or higher. The SPD 1428 
KSU must have IRS level “S” or later, and the SPD 2858 CPB board must have IRS level “H” or later in order for 
these features to operate properly. 
CUSTOMER DATABASE PROGRAMMING 
Upload/Download Routine 
SYSTEM TIMERS 
Reminder Ring Timer (Button 18) 
Release Guard Timer (Button 19) 
NbEX!$ II-ICE=. 
SYSTEM FEATURES 
Call Cost Display (Button 11) 
Handset Volume Adjustment (Button 13) 
Call Qualifier Tone (Button 14) 
Privacy Release Tone Option (Flash 06, Button 1) 
Flash Rates (Programmable) (Flash 07, Buttons 1-4) 
CO L:NE Al-TRIBUTES 
DISA Programming Options (Button 7) 
Trunk Direction (Button 13) 
Ring Delay Timer (Button 14) 
STATION ATTRIBUTES 
CO Line Ringing Options (Reminder Ring) (Button 13) 
ICLID FEATURES (Features available with optional software) 
Caller Entered ICLID digits 
Expanded ICLID Ringing Assignments (Flash 43, Button 1) 
ACD FEATURES (Features available with optional software) 
ACD Group Expansion to 16 Groups/l6 Members (Flash 60, Flash 64) 
Guaranteed Message Announcement (Flash 60, Button 11) 
ACD Event Trace (Flash 63, Buttons 1 812) 
UCD FEATURES 
UCD Station Assignments (Flash 60, Page B, Buttons 1 thru 8) 
VOICE MAIL FEATURES (Features available with optional software) 
Enhanced Voice Mail Integration (Flash 65) 
Vodavi Communications Systems 
Page 1 of56 TF NO. 43 
8300 E. Raintrw Drive Scottsdale, AZ 85260 
(@a 443aooo  
						

							Key Station Nraturesl2.3 
FEATURE CALL ADDITIONAL 
TA!$;;; YE;;;;;: PROCESSING NETWORK & COMBINATION 
EQUIPMENT 
FEATURES TRUNKING PKG 
REQUIRED 
tccount Codes 
Attendant Recall 
Automatic Call Bad< Timer 
Automatic Call Distribution (ACD) 
Agent Positions 
Alternate ACD Group Assignments 
Group Member Status 
Guaranteed Message Announcement 
Incoming CO Direct Ringing 
No-Answer Recall Timer 
No-Answer Retry Timer 
OverRow Station Assignments 
ACD Event Trace 
Recorded Announcements (RAN) 
l 
0 0 
l 0 
l 
N ., l 0 l 0 
N 
0 l l l 
N 
l 0 
N 
l l 
N 
l l 
N 
l l 
N 
l 0 
RAN Device(s) 
0 0 
N 
l 0 
N 
l a 
N 
l 0 
N 
0 a 
PCrrerminaUPrinter 
0 
l RAN Device(s) 
k&ground Music 
Battery Back-up (Memory) 
Busy Lamp Field (BLF) 
N=No additional hardware required  
						

							Key Station Featb 
FEATURE 
STANDARD 
FEATURES 
Eall Announce - Privacy 
Call Back 
Call Cost Display Feature 
Call Forward: Preset 
ACD Groups 
Hunt Groups 
Off-Net 
Stations 
UCD Groups 
VM Groups 
Call Forward: Station 
All Calls 
Busy 
Busy/No Answer 
No Answer 
Off-Net 
Call Park 
Call Pick-up 
Directed Call Pick-up 
Group Pick-up 
Call Transfer 
Caller Eotered ICLID Digits 
Calling Station Tone Mode Option 
CampOn 
Camp-On Recall 
Canned Toil Restriction 
Centrex Compatibility 
‘es/2.3 Software Packages 
I I I I 
CALL 
NETWORK & COMBINATION 
FE;;;;:: PROCESSING TRUNKING 
PKG 
FEATURES ADDITIONAL 
EQUIPMENT 
REQUIRED 
l 
I. 1. IO I N 
N=No additional hardware required  
						

							c 
Key Station Features/P.3 Software Packages 
FEATURE COMBINATION 
PKG ADDITIONAL 
EQUIPMENT 
REQUIRED 
l 
N 
l 
NI 
l I N 
l 
I N 
l 
I N 
l 
I N 
l 
I N 
l 
N 
l 
PC/Terminal 
l Printerfletminal 
l Printer/Terminal 
l 
N ’ 
I 
N=No additional hardware required  
						

							Key Station Featuresl2.3 Software Packages 
DISA Call Forwardin COMBINATION 
PKG ADDITIONAL 
EQUIPMENT 
REQUIRED 
0Pxmv supply 
PFw12v supply 
N 
N 
N 
l 
I N 
l 
1 Paging Equipment 
I , 
N=No additional hardware required