Konica Minolta bizhub 420 User Manual
Have a look at the manual Konica Minolta bizhub 420 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 61 Konica manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 528
11Supplies & Handling
11-14 bizhub 500/420/360 (Phase 3)To replace the staple cartridge for Finisher FS-510
0Be sure to replace the staple cartridge after displaying the message,
otherwise the machine may be dameged.
0When replacing the staple cartridge, touch [Add Staples] to move the
stapler toward the finisher front door. If necessary, turn the stapler
moving knob to bring the stapler forward.
1Touch [Finishing] on the Basic Screen.
The Finishing Screen will be displayed. The [Add Staples] key will...](http://img.usermanuals.tech/thumb/2790/37208/w64_Konica_Minolta_bizhub_420-527.png "Page 528
11Supplies & Handling
11-14 bizhub 500/420/360 (Phase 3)To replace the staple cartridge for Finisher FS-510
0Be sure to replace the staple cartridge after displaying the message,
otherwise the machine may be dameged.
0When replacing the staple cartridge, touch [Add Staples] to move the
stapler toward the finisher front door. If necessary, turn the stapler
moving knob to bring the stapler forward.
1Touch [Finishing] on the Basic Screen.
The Finishing Screen will be displayed. The [Add Staples] key will...")
Supplies & Handling11 bizhub 500/420/360 (Phase 3) 11-17 9Return the staple holder to the stapler, and push it down until it clicks in place. 10Close the finisher front door. Stapler will return to its original position, then the Basic screen will be restored. 2 1 Downloaded From ManualsPrinter.com Manuals
11Supplies & Handling 11-18 bizhub 500/420/360 (Phase 3)To replace the staple cartridge for Saddle stitcher SD-502 0Be sure to replace the saddle staple cartridge after displaying the message, otherwise the machine may be dameged. 1Pull the saddle stitcher tray open and hold it as it is. – It is not possible to leave the tray is kept open.Do not release it suddenly. – If the extensible tray of the tray 1 just under the saddle stitcher tray is withdrawn, push it back to its original position, otherwise it may disturb you in the following procedure or machine trouble may occur. 2Remove the staple holder. – Push down the staple holder as shown right, then pull forward to remove it. – Please check the message which stapler to remove. Saddle staple cartridge 1: rear side Saddle staple cartridge 2: front side – Gently return the saddle stitcher tray to its original position. 3Remove the empty saddle staple cartridge. – Push the two PUSH buttons of the staple holder to slide the top cover upward, then remove the empty saddle staple cartridge. 1 2 Downloaded From ManualsPrinter.com Manuals
Supplies & Handling11 bizhub 500/420/360 (Phase 3) 11-19 4Install the new saddle staple cartridge into the staple cartridge. – Firmly insert the new cartridge into staple holder. 5Push down the top cover to return it to its original position. 6Remove the lock tape from the cartridge. 7Return the staple holder to the stapler. – Hold the staple holder as shown right. Downloaded From ManualsPrinter.com Manuals
11Supplies & Handling 11-20 bizhub 500/420/360 (Phase 3)– While keeping the saddle stitcher tray open, push in the staple holder to its original position, then pull it up until it clicks in place. – Gently return the saddle stitcher tray to its original position. 8Open the stapling part of the saddle stitcher, then close it. The saddle stitcher will be reset, and the copying job using Fold & Staple mode will be available. Downloaded From ManualsPrinter.com Manuals
Supplies & Handling11 bizhub 500/420/360 (Phase 3) 11-21 11.4 Emptying Dust Boxes Even when the punch dust box of the Finisher FS-511 is full, the message is not displayed. Before using punch mode, perform the following procedure to check if the punch dust box, if needed. To empty the dust box, see the following pages. When the punch dust box of the Punch unit PU-501 mounted on the Finisher FS-510, the following message will be displayed on the screen, and the finished set will be output without being punched. To empty the dust box, see To empty the dust box of PU-501 on page 11-24. Downloaded From ManualsPrinter.com Manuals
11Supplies & Handling 11-22 bizhub 500/420/360 (Phase 3)To empty the dust box of FS-511 0Even when the punch dust box is full, the message is not displayed. Before using punch mode, perform the following procedure to check if the punch dust box, if needed. 0The punch dust box is not disposable. Be sure to return it to its original position. 1Slide the finisher to the left. – Holding the finisher handle on the top, slide the finisher to the left until it stops. 2Open the finisher right door FN7. 3Pull out the punch dust box. Downloaded From ManualsPrinter.com Manuals
Supplies & Handling11 bizhub 500/420/360 (Phase 3) 11-23 4Empty the punch dust box. 5Return the punch dust box, then close the finisher right door [FN7]. 6Slide the finisher to the right to return it to its original position. Downloaded From ManualsPrinter.com Manuals
11Supplies & Handling 11-24 bizhub 500/420/360 (Phase 3)To empty the dust box of PU-501 1Open the finisher front door. 2Pull out the punch dust box. 3Empty the punch dust box. 4Return the punch dust box, then close the finisher front door. – Firmly reinstall the punch dust box. Downloaded From ManualsPrinter.com Manuals
12Troubleshooting Downloaded From ManualsPrinter.com Manuals