Vodavi Starplus Spd 4896 Hybrid Key Telephone System Installation Manual

							STARPLUS @ SPD 4896
Digital Key Telephone System1NlTlALlZE DATABASE PARAMETERS
INIT. DATABASE PARAMETERS (Cont’d)N. System Reset
Programming Steps
If the system needs to be reset but not initialized:
1.Press the RESETflexible button (Button #20).The following message will be shown on the
display phone:Description
This feature provides a hard system reset from thekeyset instead of the KSU. This is useful in cases
where miscellaneous data errors have occurred and
the system needs to be reset without initializing the
entire database.
2. To reset the system without initializing the
database, press the HOLD button. No Confir-
mation tone will be heard and the system will
now reset.
issue 1, March 1994670-I 9 
						

							STARPLUS @ Sf’D 4896
Digital Key Telephone System
TABLE OF CONTENTS FOR SECTION 675
SECTION 675PRINTING SYSTEM DATABASE PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .675-l
675.1INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .675-l
A.
B.
C.
D.
E.
F.
G.
Ii.
I.
J.
K.
L.
M.
N.PrintingSystemParameters
..........................................................675-2
PrintingCOLineAttributes.............................................................675-4
PrintingStationAttributes..............................................................675-6
PrintingCO andStationPortParameters......................................675-8
Printing Exception Tables
............................................................675-l 0
PrintingSystemSpeedBins.........................................................675-l 2
PrintingLCRTables.....................................................................675-l 4
PrintingEntire SystemData Base...............................................675-23
PrintingICLIDTables...................................................................675-24
PrintingDirectoryDialing TableParameters................................675-27
PrintingHunt GroupParameters.................................................675-29
Printing ACDor UCDGroupParameters....................................675-31
Printing VoiceMailGroupParameters
........................................675-33
Abort
Printing...............................................................................675-35
issue 1, March 1994675-i 
						

							STARPLUS @ SPD 4696
Digital Key Telephone SystemPRINTING SYSTEM DATABASE PARAMETERS
SECTION 675
PRINTING SYSTEM DATABASE PARAMETERS
675.1INTRODUCTION
Programming Steps
If the system is in the programming mode, continue
using the program codes. If starting to program here,
enter the programming mode. Refer to Sec. 600.2,
Program Mode Entry (Key Station).
If 
DataBase Parameters need to be printed:
1.Press FLASH and dial [85]. The following willDescription
This section describes the procedures and steps
necessary to print Data Base Parameters and 
vari-ous portions of the 
syster_n.:The buttons on the key telephone are defined as
shown below when entering the Print Data Base
Parameters programming area.
be shown on the display phone:
-2. Choose the portion of the database to be
printed by pressing the appropriate button in
the flexible button field.
98STATON AlTNI8VTES
Pcm-STm
1. 5TEXCEPTIGNTABLES
STsYsiEMsEEo7 u
LCR TASLPI
IJfEN-im5SYsTEu
8 0ICLwTA8LES
‘, m PDE(ECTOAYDULTASLSS14 F 
,’18 Q 
i1  18 
H !
AaGRTPRINltNa= i*Features available with optional software.
With a printer connected to the RS-232C port (future)of the Central Processor Unit (CPU) or to either Port
#3 or Port #4 on the I/O Expansion Module, the
currently stored customer database can be printed
or “uploaded” into a file. This command allows the
entire database to be “dumped” as a permanent
record which can serve as a hard copy of the data-
base .The system Baud rate must match that of the printer
or receiving device.
Refer to the following Figures for examples of the
database printouts. Also refer to the following para-
graphs for instructions on printing only portions of thedatabase .
Default: None
Related Programming: Refer to Sec. 610.8, Baud
Rate Assignments, for setting the baud rate of the
RS-232C port (future) on the Central Processor Unit
(CPU), Pot-t 
#3 or Port #4 on the I/O Expansion
Module.
issue 1, March 1994675-l 
						

							‘RINTING SYSTEM DATABASE PARAMETERS
STARPLUS @ SPD 4696
Digital Key Telephone System
iystem 
DataBase Printouts (Cont’d)
4. Printing System Parameters
Programminq Steps
f a printout of all System Parameters is desired:
1. Press the SYSTEM PARAMETERS flexible
button (Button 
#l). The following message
will be shown on the display phone:
2. To print the system parameter database ,
press the HOLD button. The following mes-
sage will be shown on the display phone:
RJhen the system has finished sending the informa-ion to the printer, confirmation tone will be heard.
System Timers:
SHR= System Hold Recall Timer
EHR= Exclusive Hold Recall Timer
ART= Attendant Recall Timer
XFR= Transfer Recall Timer
PFT= Preset Forward Timer
CFN= Call Forward No-Answer Timer
PT= Pause Timer
CPT= Call Park Timer
CFT= Conference Timer
PTO= Page Timeout Timer
COT= CO Ring Detect Timer
SRT= Single Line Receiver Timer
MWT= Message Wait Reminder Tone
HFT= Hook FIash Timer
HFD= Hookswitch Bounce Timer
CQT= SMDR Call Qualification Timer
ACB= Auto Call Back Timer
RR= Reminder Ring Timer
RG= Release Guard TimerDescription
With a printer connected to the RS-232C port (future)
on the Central Processor Unit (CPU) or to either Port
#3 or Port #4 on the I/O Expansion Module, the
currently stored customer database can be printed
or “uploaded” into a file. This command allows the
System Parameters database to be “dumped” as a
permanent record which can serve as a hard copy.
The system Baud rate must match that of the, printeror receiving device.
When printing the System Parameters the following
data is printed;l All System Timers
l All System wide options (i.e. external night
ringing, Hold preference etc...)
o Attendant programming
e Other system assignments (i.e. Page/Re-
lay Assignments, Executive/Secretary,
SMDR etc...)l Weekly Night Mode schedule
Refer to the following Figure for an example of the
system parameters database printout.
Default: None
Related Programming: Refer to Sec. 610.8, BaudRate Assignments, for setting the baud rate of the
RS-232C port on the Central Processor Unit (CPU),
Port 
#3 or Port #4 on the I/O Expansion Module.
System Features:AO=Attendant Override
SY= Hold Preference
ENR= External Night Ringing
EO=Exec Override Warn Tone
PW= Page Warning Tone
BGM= Background Music
LCR= LCR Enable/Disable
AC=Forced Account Codes
GL=Group Listening
S=ldle Speaker Mode
CC= Call Cost Display Feature
MH= Music On Hold
V= Handset Receiver Gain
Q= Call Qualifier Tone Option
575-2Issue 1, March 1994 
						

							STARPLUS @ SPD 4896
Digital Key Telephone System
PRINTING SYSTEM DATABASE PARAMETERSSYSTEM PARAMETERS
Eng. 
Ver.2.3D-OFFFSYSTZM TPIEISaSHR EHR ART XFR 
PFT CFN PT
60 180
145
1015 2
CDT CFT 
_ _DmO COT SRT ?lWT HCT18010 15 3 20
0 10
HFD CQT AC3 RR RG10 30
0 0 3
SYSTZM ZATURES
A0 SY 9NR EO PW BGM LCR
N
YX YYYNAC GL S CC 
MH V QN NY N YSN
3ARG2IN WARN TON?ZNAiJL,?3
SYSTEMLZD SLASH RATZS
INC CO FNG30 I?M FLAS%INCICM RISG120 13M SLiJTT7RCALLTORWA??30 11M FLASH-XESSAGE WAZING15IPM TLASH
AT3TxIqT STATIONS
100 ### ##iRELAY/SENSOR 
###1 NONE
2 NONE3 NONE
4 NONE
5 NONE
6 NONE
RELAY/SENSOR 
###1 NONE
2 NONE
3 NONE
4 NONE
5 NONE
6 NONE
RELAY/SENSOR 
###
1 NONE
2 NONE
3 NONE
4 NONE
5 NONE
6 NOIdEI/O 
3AUD ,3ATE--
Port 1 / On 3oard = 2400
20x 2 ! Xoden=1200?orz 3i FE232 =2400
?‘ort4 / ma22 =2400
ACCZSS CODE1 3ISA ACC,cSS
1002 
ADMiN ZASSWOEID3226
SDR T?5_3NT 3AUD ?ORTNLD 802400 1AUTO 
NIGZ MODENWEEKLY NIGHT MODE 
SC:-:ZDULZ
Figure 675-l DB Printout of System Parameters
Issue 1, March 1994
675-3 
						

							PRINTING SYSTEM DATABASE PARAMETERSSTARPLUS @ SPD 4696
Digital Key Telephone SystemSystem 
DataBase Printouts (Cont’d)
B.Printing CO Line Attributes
Programming Steps
If a printout of the CO Line Attributes is desired:
1. Press the CO 
LINE ATTRIBUTES flexible
button (Button 
#2). The following message
will be shown on the display phone:
To print the data for ALL CO Lines, press the
HOLD button. To print CO Line data for a
specified CO Line Range enter four digits to
specify the CO Line range (two digits for the
first line within the range and two digits for the
last line in the range i.e. 
[0115]). If a printout
of only one line is desired enter that line twice
(i.e. 
[Ol 011). Then press the HOLD button.
3.The following message will be shown on the
display phone and the CO Line data will be
printed:When the system has finished sending the re-
quested information to the printer, confirmation tone
will be heard.Description
With a printer connected to the RS-232C port (future)on the Central Processor Unit (CPU) or to either Port
#3 or Port #4 on the I/O Expansion Module, the
currently stored customer database can be printed
or “uploaded” into a file. This command allows either
a range of CO Lines or the entire CO Line database
to be “dumped” as a permanent record which can
serve as a hard copy of the CO Line attribute data-
base .. “.The system Baud rate must match that of the printer
or receiving device.
When printing the CO Line attributes the following
data is printed:
.
*
*Refer to
CO Line
Default:
RelatedAll CO Line parameters within the specified
range.
CO Line ringing assignments within the
specified range.
Dial Pulse Ratio and Speed settings
the following Figure for an example of the
attribute database printout.
None
Programming: Refer to Sec. 610.8, Baud
Rate Assignments, for setting the baud rate of the
RS-232C port on the Central Processor Unit (CPU),
Port 
#3 or Port #4 on the l/O Expansion Module.
Definition of Terms for CO Lines Printout
SIGNAL= 
DTMF/Dial Pulse
TYPE= 
CO/PBXUNA= Universal Night Answer
PRI= CO Line Privacy
SUPV= Loop Supervision
DISA= Direct Inward System Access
FLTM= Flash Timer
GRP= CO Line Group
COS= CO Line Class of Service
DIR= Trunk Direction
RD= Ring Delay Timer
675-4
Issue 
;, March 1994 
						

							STARPLUS@ SPD4996Digital Key Telephone SystemPRINTING SYSTEM DATABASE PARAMETERS
r
co 05
--
LiNE 05
CO LINE ATTRIBUTES
co 01
LINE 01SIGNAL TYPE UNA CONF PRI
DTMF CO YY YSIGNAL TYPE C?A CONF PRIDTMF co Y
Y Y
SrjPV DISA FLTM GRP COS DIR RDx\T13 1 12JOSi;SV 3iSA lLTM GRP COS DiR 3D
NN1011200RING ASSZG1WZNTS
100s
RING ASSIGNMENTS
1009co 06
--
LINE 06co 02
--
LINE 02SIGNAL TYPE UNA CONF DRIDTMF CO YY YSIGNAL TYPE LTNA CONF PRI
DTPP co Y _ -v vSUPV 3ISA FLTX GRP COS DIR RD
N N 1011200
COS DIR RD12003iNG ASSIGNMENTS
1005
SiTPV DISA FLT??: GR
?u;N10 :
XNG ASSiGbiENTSlOOB
Pco 07
--
LINE 07 co 03
I
:  --
j 
LINE 03
rSJPV 3ISA 3’2TM GRP c3S DIR 523xNLO11200RING ASSIGLNMENTS
LOOT3
co 08--
;INZ 08
3ING ASSIGNMENTS1003
- 7’ i?4--- -
. . .and so oc ;hr~; CO Linqs 48Figure 675-2 
DB Printout of CO line Attributes
issue 1, March 1994675-5 
						

							PRINTING SYSTEM DATABASE PARAMFTERS
STARPLUS @ SPD 4696
Digital Key Telephone System
System 
DataBase Printouts (Cont’d)
C. Printing Station Attributes
Programming Steps
If a printout of the Station Attributes is desired:
1. Press the STATION ATTRIBUTES flexible
button (Button 
#3). The following message
will be shown on the display phone:
PRESS HOLD
2.To print data for all stations, press the HOLD
button. To print Station data for a specified
Station Range enter six digits to specify the
Station range (three digits for the first station
within the range and three digits for the last
station in the range i.e. 
[lo01 091). If a printout
of only one station is desired enter that stationtwice (i.e. 
[lo1 1011). Then press the HOLD
button.
3.The following message will be shown on the
display phone and the requested information
will be printed:
1
PRINTING STATIONS1
When the system has finished sending the re-
quested information to the printer, confirmation tone
will be heard.
Paae “A” Features:
PAGE= Paging Access
DND= Do Not Disturb
CONF= Conference
EOR=Executive Override
PRI= Privacy
SPD= System Speed Dial Access
QUE= Line Queue Access
PLA= Preferred Line Answer
OHVO=Off-Hook Voice Over
FWD= Station Call Forward Access
LCR= LCR Class of Service
SUB= ACD Supervisor Monitor Barge-in
REM= CO Line Ringing OptionsDescription
With a printer connected to the RS-232C port (future)on the Central Processor Unit (CPU) or to either Port
#3 or Port #4 on the I/O Expansion Module, the
currently stored customer database can be printed
or “uploaded” into a file. This command allows either
a range of station data or all stations data informationto be “dumped” as a permanent record which can
serve as a hard copy of the station attribute data-
base.The system Baud rate must match that of the printer
or receiving device.
When printing the Station attributes the following
data is printed;
l All current station parameters
Refer to the following Figure for an example of a
Station attribute database printout.
Default: None
Related Programming: Refer to Sec. 610.8, Baud
Rate Assignments, for setting the baud rate of the
RS-232C port on the Central Processor Unit (CPU),
Port 
#3 or Port 84 on the I/O Expansion Module.
Pa e “5” Features:
SID= Station IDAID= Associated ID 
(DSSDLS Console)
DCOS= Day Class of Service
NCOS= Night Class of Service
SPK= Speakerphone Option
PICKUP= Pickup Groups
PAGE= Paging Groups
PREFWD= Preset Forward Assignment 
-
LCOS=LCR Class of Service
BUTTONS= Refer to Table 630-2 Flexible Button
Display Designations, Page 630-22.
675-6
Issue 1, March 1994 
						

							STARPLUS @ SPD 4696
Digital Key Telephone SystemPRINTING SYSTEM DATABASE PARAMETERS
STATION ATTRIXJTES
STA 100
PAGE DND CONF ZOR PRI SPD QUEY Y YN/A Y Y Y
ILA OHVO FWD 3CR SUE REXNN Y N NNSI3 AID 3cos sicos SPK
0_(i03ICXUO PAG; IRETWD LCOS
110CO ACCESS 1
3UTmONS
O&O0 02DlOl 03D10204D103 05Di04 06D105
07D106 08D107 09D10810D109 llDl10 12Dlll
13coo1 l4COO2 15coo3LSCOO4 L7C005 18cOO6
19L12OPL1 21C3K22FwD23DND2acwSTA 
101
STA 102
PAGE DND CONF EOR PRI SPD 
QUEY Y YN/A Y Y YPLA OHVO Fwl LCR SUE REM
NN Y N N N
SID AID DCOS NCOS SPK01.l 0FICKUP ?AGE DREFWD LCOS10CO ACCESS 1
3UTTONSOlDlOO 02DlOl 03D102
04D103 05D104 06D10507Di06 08D107 09D108
lOD109 1lCOOi 12COO213coo3 14C004 15coo5
16COO6 17coo7 18COO819LP2OPLl 21CPO22LQU23C3K 24PKZ25MSG 26FWD 27DND
28CNZ
STA 103
?AGE DND CONF EOR PRI SID QUEvVv- _X/A YY vai OF/-0 WD T.lCR SUE REX-NNvxNNSiD AI3 3COS ?JCOS SPK01i03TCKUT ?AGE ?RZFN‘D LCOS110CO ACC3SS 1
3mmovsA L0310002310103Dl02
04310305Di0406Dl.0507>106 08D107 09D108
10T.0911COOl 12COO213coo3 L4CO04 1scoo5
16COO6 17COO7 18COO8
1922O_SL12iCP0
22;QU23c3x2 4 IKij-25MSG2 6hTl273x>2 ~CNZ1
Figure 675-3 
DB Printout of Station Attributes
Issue 1, March 1994
675-7 
						

							PRINTING SYSTEM DATABASE PARAMETERSSTARPLUS @ SPD 4896
Digital Key Telephone SystemSystem 
DataBase Parameters (Cont’d)
D.Printing CO and Station Port Parameters
Programming Steps
If CO/Station parameters need to be printed:
1. Press the CO/Station Port Parameters 
fiex-ible button (Button 
#4). The following mes-
sage will be shown on the display phone:
yiiG&Ep
PRESSHOLD2. To print the CO/Station Port parameters,
press the HOLD button. The following mes-
sage will be shown on the display phone:
+When the system has finished sending the re-
quested information to the printer, confirmation tone
will be heard.Description
With a printer connected to the RS-232C port (future)on the Central Processor Unit (CPU) or to either Port
#3 or Port #4 on the I/O Expansion Module, the
currently stored customer database can be printed
or “uploaded” into a file. This command allows either
a range of station data or all stations data informationto be “dumped” as a permanent record which can
serve as a hard copy of the station attribute data-
base.. “.The system Baud rate must match that of the printer
or receiving device.
Refer to the following Figure for an example of a
Station attribute database printout.
Default: None
Related Programming: Refer to Sec. 610.8, Baud
Rate Assignments, for setting the baud rate of the
RS-232C port on the Central Processor Unit (CPU),
Port 
#3 or Port #4 on the I/O Expansion Module.
675-8Issue 1, March 1994