Vodavi Starplus Spd 4896 Hybrid Key Telephone System Installation Manual

							STARPLUS @ SPD 4896Digital Key Telephone SystemINSTALLATION
Figure 500-14 Digital Terminal Wall MountingIssue 1, March 1994500-23 
						

							STARPLUS @ SPD 4696
Digital Key Telephone System
INSTALLATlONSLT device. Additionally, a CO line may be
wired to the second pair of the SLT modular
connector for Power fail operation.
Cable Loop Limits:The maximum loop limit from the KSU to the
SLA (OPX) adapter is 1000 feet.
The maximum loop limit from the SLA (OPX)
adapter to the connected SLT or device is 1400
ohms not including the telephone or device.
500.6POWER FAILURE TRANSFER
A.Relay 
/ Sensor Interface ModuleThe Relay Sensor Interface Module connects
to the system using one digital station port and
provides three relay activated contacts and
three sensing circuits. The relays provide for
applications such as Loud Bell Control con-
tacts, CO Line control contacts, RAN Start con-tacts, Page Relays, Power Fail contact and
additional applications as software will permit.
The sensing circuits will provide for such appli-
cations as RAN Stop (end of message).
Connections:
All connections to the Relay Sensor Module aremade on the back of the unit. Two terminal
strips with screw terminals each provide con-
nection to the ancillary devices for relay control
or sensing monitoring. The Modular jack
marked KSU is connected to a KSU Digital
terminal station port. This connection requires
all four wires and wires the same as a key
station. Refer to Figure 500-l 6 Relay 
/ Sensor
Interface Module for wiring information.
An external power source may be required to
drive equipment connected to the relay con-
tacts. The contacts are rated at 24Vdc max. at
1 amp.
Cable Loop Limits:The maximum loop limit from the KSU to the
relay Sensor Module is 1000 feet.
B.Power Failure Transfer Unit (PFTU)This unit provides the relay transfer circuits for
up to 12 CO lines in the event of a power or
processor failure. The unit is housed in its own
enclosure and mounts external to the KSU.
Activation of the 
PFT relays is controlled by the
Relay/Sensor Interface Module that is pro-
grammed for 
PFT. A customer provided 12V dc
power supply is required to operate the unit.
There is a manual switch that activates the
PFTM for testing purposes.
With loss of power to the system or a failure of
system processing, the PFTU will automaticallyconnect up to twelve CO lines to prewired
500/2500 type telephones. Wherrpower is re-
stored, the 
PFTU will automatically restore the
CO trunks and stations to normal operation.
These SLT stations do not have to be used for
intercom, but can be if so desired. Refer to
Figure 500-17 Power Failure Transfer Wiring
Options.
Wiring / Pinouts / Connections:The PFTU has two 
50-pin male amphenol con-
nectors labeled 
CONNl and CONN2 located
on the front of the unit. Each connector wires
six CO lines for power fail transfer. Refer to
Table 500-4 
PFTU Conn A Connecting Block
and Table 500-5 PFTU Conn B Connecting
Block for pin-outs of each of the connectors.
The PFTU is connected to the KSU via the
modular connector on the side of the unit. This
is connected in series to a customer provided
12V dc supply. and to a multi use relay pro-
grammed as a power failure relay.
500-24issue 1, March 1994 
						

							STARPLUS @ SPD 48%
Digital Key Telephone SystemINSTALLATION
GREENl-r
TRRT
RR!
I
iiI  STATIONI/(jCONNECTING
! IBLOCK
MODULAR:  I
CABLE
L-L!- -
MDFPFT Ring j
SLT Ring1  /  
PFTTip/
/  
SLTTip
,-KSU
n”un Customer Provided-48V dc Power Supplyl/2 amp per OPX unit
9‘,-.--JGreen to Phone
Red to Phone
BlacK to Trunk Tip
Yellow 
!o Trunk Ring
Figure 500-15 Off-Premise Extension 
(OPX) Module
Issue 1, March 1994
500-25 
						

							INSTALLATIONSTARPLUS @ SPD 4896
Digital Key Telephone System
XMIT TIP
XMIT RINGRCVE TIP
RCVE RING
STATION
CONNECTING
BLOCK
:.;,MODULAR
CABLE
I
/
- RELAY
’/ SENSOR //
1  Device Output Relay 1
(dry contacts)/  (ie: RAN Device) /
j
Loud Bell Control1  External Page Device
RAN Device
1  Power Failure Transfer
!  
Starpius Tri-Output
124 VDCI
Power Supply ,
1 Amp Max.
I
/
or 24VDC 1 Amp Power Supply
(Customer Provided)NOTE: RAN device does notrequire external power supplyFigure 
500-16 Relay / Sensor Interface Module
500-26issue 1, March 1994 
						

							STARPLUS @ SPD 4896
Digital Key Telephone SystemINSTALLATION
L
OPXI
II IIPFT TIPINCO 1 TIP IN
,------------------CO 1 RING IN
_____-___-____
PFI- RING
SLT RING
(SLT or DEVICE),
iiMethod 
#I
Power Failure Transfer Unit (P-U)Method #2Customer
Provtded
Battery
+ -RELAY / SENSOR
INTERFACE MODULE
12VDC1AMPI,’ ,nCOM i  
]:b :r--,/ ~
N.C. CONTACT /  
- ‘>m-.’ :1-bI-j
Multi-Purpose RelayFigure 500-17 Power Failure Transfer Wiring Options
Issue 1, March 1994
500-27 
						

							INSTALLATIONsTAFlPLUi@ SPD 48%Digital Key Telephone System
POWER FAILURE TRANSFER UNIT 
(PFTU),----------------__CHAMP CONN 1
STAl TIP OUT..-___-.--___-__- WMjN -w
STAl RING OUT
ISIX CIRCUITS
I
I
I
I
I
I
I
I
I
II
i
I
II
I
I
I
I
I
I
I
I
I
I
I
I
I
I
II
II
I
I
--------------____IFigure 500-18 Power Failure Transfer Circuit
500-28
issue 
1, March 1994 
						

							STARPLUS @ SPD 4896
Digital Key Telephone SystemINSTALLATION
Table 
500-4 PFlIJ Conn A Connecting Block
T-
i-‘piiI
I  
1/  2
:  3fI
!
4
/
5
PIN
26
127
2
28
3
294
30
5
31
6
32
7
33
834
9
35
10
36
11
37
12
38
13COLOR
WH/BLBUWH
WH/OR
OR/WH
WH/GN
GN/WH
WH/BN
BN/WH
WH/SL
SLIWH
RD/BL
BURD
RD/OR
OR/RD
RD/GN
GN/RD
RD/BN
BN/RD
RD/SL
SURD
BK/BLBUBK
BWOR
OR/BK
BWGN
GN/BK
SK/BN
BN/BK
BWSLSUBK
YUBL
BLIYLYUOR
OPl/YLYUGN
GNNL
YUBN
BNNL
YUSL
SUYL
VIIBLBWI
VI/OR
ORNI
DESIG
1TIT
1TIR
1STAINTIP
1 STA IN RING
1 TRK OUT 
TIP1 TRK OUT RING
1STOT
1STOR
2TIT
2TIR
2STAINTIP
2 STA IN RING
2 TRK OUT TIP
2 TRK OUT RING
2STOT
2STOR
3TIT
3TIR
3STAINTIP
3STAINRING
3 TRK OUT TIP
3 TRK OUT RING
3STOT
3STOR4TIT
4TIR
4 STA IN TIP
4 STA IN RING
4 TRK OUT TIP
4 TRK OUT RING
4
STOT4STOR
5TIT
5TIR
5 STA IN TIP
5STAINRING
5 TRK OUT TIP
5 TRK OUT RING
5STOT
5STOR
6TIT
6TIR
6 STA IN TIP
6 STA IN RING
6 TRK OUT TIP
6 TRK OUT RING
6STOT
6
7
8/
9I
10I
11/
/
I
,
12I  13I
I
/
i  
‘14 i  :;j
15/   /40,5
l641
16
17
42‘7
J8 z
I944
19
2o:2j  21 I  
;yI
22~47
)22
2348 
VI/GNI  23 j  
GNNI2449
VI/BN24
BNNI6 STOR
25I  50 j  VI/SL :
25 :  
SWITable 
500-6 PFFU Conn B Connecting Block
LPAIR
1
2
34
5
67
I
8/
9/
101
/
11I
12/
13I
I
14!
I
15/
16:  17
18:  19
!  20
~  
21/
;  22
’  23
i  24
i  25
:-
PINCOLOR
26
WH/BL
1BL/WH27
WH/OR
2OR/WH28
WH/GN3
GN/‘WH29
WH/BN4
BN/WH30
WH/SL
5SUWH
31RD/BL
6BURD32
RD/OR7
OWRD33
RD/GN
8GN/RD34
RD/BN
9BN/RD
35RD/SL
10SURD36
BWBL
11BUBK
37
BK/OR
12OWBK
38BWGN
13GN/BK
39BKIBN
14
BN/BK40
BWSL
15SUBK
41YUBL
16BLJ’YL42YUOR
17ORIYL43
YLIGN
18GNNL
44
YUBN
19BNNL
45
YUSL20
SUYL46
VI/BL
21BWI47
VI/OR
22
ORNIDESIG
7 TIT
7 
TIR‘.7 STA IN TIP
7 STA IN RING
7 TRK OUT TIP
7 TRK OUT RING
7 STOT
7 STOR
8 TIT
8 TIR
8 STAIN TIP
8 STA IN RING
8 TRK OUT TIP
8 TRK OUT RING
8 STOT
8 STOR
9 TIT
9 
TIR9 STA IN TIP
9 STAIN RING
9 TRK OUT TIP
9 TRK OUT RING
9 STOT
9 STOR
10 TIT
10 TIR
10 STA IN TIP
10 STA IN RING
10 TRK OUT TIP
10 TRK 
OUTRIN G
10 STOT
10 STOR
11 TIT
11 TIR11 STA IN TIP
11 STA IN RING
11 TRK OUT TIP
11 TRK OUT RING
11 STOT
11 STOR
12 TIT
12TIR -12 STA IN TIP
12 STA IN RING
12 TRK OUT TIP
12 TRK OUT RING
12 STOT
12 STOR 24 ’BNNI
50 :  
VIISL25
SWI j
Issue 
I, March 1994500-29 
						

							INSTALLATIONSTARPLUS @ SPD 4896
Digital 
Key Telephone System500.9INSTALLING RECORDED AN-
NOUNCEMENT DEVICE (RAN)
The Recorded Announcement feature (RAN) is used
with either the Automatic Call Distribution (ACD) or
Uniform Call Distribution (UCD) features to provide
unanswered incoming CO calls or calls in queue witha Recorded Announcement while waiting for an
available ACD or UCD station. The system may be
programmed to provide this announcement on
specified RAN output ports on the system (unused
SLT and CO ports). The system can be programmed
to connect the waiting caller to a different RAN port
for the second, and subsequent RAN messages.
CO RAN CONNECTIONS
coMDF
TIPj  VOICE____ __’ TIP ___CO Line Board(CO12)FlEiVOICE RING,--When a CO line port is used for a ground start
application, a 24V dc power source must be con-
nected to the CO line port for talk battery. A Page/Re-lay contact assigned to an announcement table in
programming would provide contact closure to start
the Recorded Announcement device.
When an SLT port is used, the RAN device must be
configured for ring trip operation (loop start). The
9OV ac voltage sent to the SLT port will be recog-
nized by the RAN device which will then answer the
call.Customer Provided
Talk Battery
24v DCSLT RAN CONNECTIONS
MDFTIP :
VOICETIP,- __Single Line TelephoneBoard (SL12) R,NGVOICE SING___-LOOP START APPLICATIONS
-’,- _.RAN
3XANVT
DEVICE
CO LINE
SLT%RT ,,VOICE INiNPUT FROM RECORDED&NNO”NCEMENT DEVICEaAN “R
2RAN cii--
REL4Y,MAAKECONTROLSTART CONTROL TOOUTPUTRAN CEVICE.--ARAN cn--RELAY
SENSOR
MODULE 
’?A?4 SNS--
“E&M” TYPE RAN SIGNALING
Figure 500-l 9 CO and SLT RAN Connections
500-30
issue 1, March 1994 
						

							STARPLUS @ SPD 4996
Digital Key Telephone SystemINSTALLATION
500.10
DATAFEATURE
The Data Feature is a time division switched, point
to point data transmission capability which permits
simultaneous (on the same system but not the sameport) voice and data communications. The Data
Feature offers the ability to transmit data information
between personal computers, printers, plotters, CRT
terminals, and main frame computer ports.
To establish a Data call, a Digital Data interface Unit
(DDIU) is required to be connected to each data
communications device. Data information can be
switched through the system at speeds of 300,1200,
2400,4800,9600,19.2K and 38.4K baud asynchro-
nous.The Digital Data Interface Unit 
(DDIU) is wired to the
Starplus Digital Key Telephone System like a digital
telephone, and requires one station port.
All connections to the 
DDIU are made on the back
panel. The back panel has a modular jack and a
DB-25 type connector. The modular jack, labeled
KSU, is used to connect the DDIU to the station portof the system. The DB-25 connector supports an
RS-232C connection and is used to connect the datadevice to the system.
A green LED lights to indicate the 
DDIU is properly
wired to the system.
GREEN
l-r
TR
RTivlDF
RR
STATlONCONNECTING
BLOCK
Figure 500-20 Digital Data interface Unit (DDIU) wiring
Issue 
1, March 199450031 
						

							INSTALLATION
STARPLUS @ SPD 4896
Digital Key Telephone SystemConnection of the individual data communication
devices requires that the installer be familiar with
data communications terms, and has access to the
appropriate information for connecting the variety of
data communications devices that may be encoun-
tered. This information consists of, but is not limited
to:1. Is the device configured as data terminal
equipment (DTE), or data communications
equipment (DCE.
2. What pin on the RS-232C type connector
performs what function?
3.What signal leads are required to make the
device operate?
When planning the installation of the data feature,
use a digital display phone at any location that is to
originate a data connection. A 
DDIU can only be
called; it cannot originate a connection. A 
DDIU
would typically be used in conjunction with the digitaldisplay phone. A 
DDIU would typically be connected
to a printer,or a MODEM.
The station wiring for a digital display phone and a
DDIU are identical.
The data connector of the Digital Data Interface Unit
(DDIU) is a 
25-pin, type D connector which is con-
figured as Data Communications Equipment with the
following pin configurations.
/
PIN 1
j  # !USEDIRECTION I
j  
2 /
Receive DataI
i  3 1DDIU I
Transmit DATA /
DDIU1  4 /
Request To Send/
DDIU ;
)  
5 j
Clear To Send!DDIUI
:  
6 1
Data Set ReadyIDDIU/
/  7 jISignal Ground j
8 1Data carrier detect1
DDIU20 IData Terminal Ready /
22 j
DDIU j
Ring Indicator j
DDIU 1
The following diagram will aid in the design of cables
to connect the many different configurations of data
communications devices.
Digital Systems Data Switching
MODEMDDIU
GNDi-1 GND
RD22RD
TD33i-DSG7
7SG
zi;: >( ii’,“,
DTFi 2020 DTRDSR 66 DSR
Al 2.2
~ 11QMModem to 
DDIU Cable
500-32Issue 1, March 1994