Sharp Mx2310u User Guide

							4-57
FACSIMILE
Contents
CHECKING THE IMAGE TO BE TRANSMITTED 
(Preview)
This function requires the hard disk drive.
If you touch the [Preview] key before scanning the original, you can check the scanned image in the touch panel before 
sending the image.
* The factory default setting is disabled.
Depending on the size of the transmission data, part of the preview image may not appear in the preview screen in the touch 
panel.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Touch the [Preview] key to highlight it. 
3
Select transmission settings and press the [BLACK & WHITE START] key.
Originals are being read appears while the originals are being scanned, and when scanning is finished, the preview screen
appears on the touch panel. Transmission will not take place until you touch the [Start Sending] key in the preview screen.
4
Check the preview image and then touch 
the [Start Sending] key.
Transmission begins.
For information on the preview screen, see PREVIEW CHECK 
SCREEN (page 4-58).
System settings (administrator): Default Preview
You can specify whether or not the [Preview] key function will be enabled in the base screens of the image send modes and 
in the address book.
AutoAuto
Auto
USB Mem. ScanFaxScan
Standard
Auto ReceptionFax Memory:100%
Internet FaxPC Scan
Scan:Send:A4
File
Quick File
Preview
Address Review
Direct TX
Sub Address
Address Book
Special Modes
Resolution
Exposure
Original
Preview
Display Rotation
/00100001
Function Rev.
Sender InfoB/W
Start
Sending 
						

							4-58
FACSIMILE
Contents
PREVIEW CHECK SCREEN
This section explains the preview check screen.
(1) Preview image
A preview of the scanned original appears.
If the image is cut off, use the scroll bars at the right and 
bottom of the screen to scroll the image. Touch a bar and 
slide it to scroll. (You can also touch the   keys to 
scroll.)
(2) Change page keys
When there are multiple pages, use these keys to 
change pages.
  keys:  Go to the first or the last page.
  keys:  Go to the previous page or the next 
page.
 Page number display:
This shows the total number of pages 
and the current page number. You can 
touch the current page number key and 
enter a number with the numeric keys 
to go to that page number.(3) [Sender Info] key
Touch to display the sender information for fax own 
number.
This key can only be touched when the entire preview 
image is displayed in the preview screen.
(4) [Function Rev.] key
Touch to check special mode settings or scan settings for 
two-sided originals.
(5) Display zoom key
Use this to set the zoom ratio of the displayed image. 
Changes from the left in the order Full Page, Twice,  
4 Times, 8 Times. The setting applies to all pages in 
the file, not just the displayed page.
(6) Display Rotation key
This rotates the image right or left by 90 degrees. The 
rotation applies to all pages in the file, not just the 
displayed page.
(7) [Start Sending] key
Touch to begin transmission.
Preview
Display Rotation
/00100001
Function Rev.
B/W
Start
Sending
Sender Info
(5)
(6)
(7)
(4)
(3)
(2)
(1)
 A preview image is an image for display on the touch panel. It will differ from the actual send result.
 The preview image reflects certain scanning and special mode settings. 
Settings reflected in the preview image are as follows: 
Scanning settings: Original 
Special modes: Erase, Dual Page Scan, Card Shot, 2in1 
						

							4-59
FACSIMILE
Contents
This section explains the basic procedures for receiving faxes.
RECEIVING FAXES
When the reception mode is set to Auto Reception, the machine will receive and print faxes automatically. The fax 
reception mode is displayed in the base screen.
FAX RECEPTION
 When fax reception is in progress, it is possible to reserve a transmission by performing the transmission in memory 
transmission mode.
☞TRANSMISSION METHODS (page 4-26)
 To print received faxes, make sure that the required paper is loaded in the machines paper trays. It is not necessary to 
load A4 (8-1/2 x 11) paper and B5 (5-1/2 x 8-1/2) paper in both the vertical ( ) and horizontal ( ) orientations. 
Differences in orientation are automatically adjusted when faxes are received. 
When a fax smaller than A4 (8-1/2 x 11) size is received, the size of the paper used for printing will vary depending on the 
orientation (vertical or horizontal) in which the sender placed the original.
System Settings: Receive Setting (page 7-105)
This is used to change the fax reception mode. Auto Reception should normally be used.
Select Manual Reception when an extension phone is connected to the machine.
System Settings (Administrator): Allow/Reject Number Setting
You can store numbers and specify whether or not reception is allowed from those numbers.
AutoAuto
Auto
USB Mem. ScanFaxScan
Standard
Auto ReceptionFax Memory:100%
Internet FaxPC Scan
Scan:Send:
File
Quick File
Address Review
Direct TX
Sub Address
Address Book
Special Modes
Resolution
Exposure
Original
Preview
This shows the current fax 
reception mode and the amount 
of free memory remaining. 
						

							4-60
FACSIMILE
Contents
RECEIVING A FAX
When a fax is transmitted to the machine, the machine automatically receives and prints the fax.
1
The machine rings and fax reception 
begins automatically.
A beep sounds when reception ends.
System Settings (Administrator): Speaker Settings
This is used to change the volume and tone of the reception beep.
System Settings (Administrator): Number of Calls in Auto Reception
This is used to change the number of rings on which fax reception begins automatically. To receive faxes without 
the machine ringing, select 0 rings.
2
The fax is automatically printed.
If a password entry screen appears...
A password must be entered to print the received fax. When the correct password is entered, the received fax is 
printed.
☞PRINTING A PASSWORD-PROTECTED FAX (Hold Setting For Received Data Print) (page 4-62)
The output tray and stapling (when a finisher is installed) can be selected.
The number of copies of received faxes that are printed and the output tray can be selected. When a finisher is 
installed, the number of copies printed, the output tray, and stapling can be selected.
 If printing of a copy job or print job is in progress when a fax is received, the fax will not be printed until the previously 
reserved job is completed.
 Received faxes will not be printed when the machine cannot print due to an error condition such as out of paper, out of 
toner, or a paper misfeed. The faxes will be printed automatically when the error condition is cleared. (If the machine ran 
out of paper, touch the [OK] key in the touch panel after loading paper.
 When received faxes cannot be printed, the faxes can be forwarded to another fax machine.
☞FORWARDING RECEIVED FAXES (Fax Data Forward) (page 4-67)
System Settings (Administrator): Duplex Reception Setting
This is used to have received faxes printed on both sides of the paper.
System Settings (Administrator): Receiving Date & Time Print
Use this to select whether or not the date and time of reception is added when a received image is printed.
Beep 
						

							4-61
FACSIMILE
Contents
RECEIVING A FAX MANUALLY
A fax can be received manually using the touch panel. While the machine rings, touch the [Speaker] key in the base 
screen and then touch the [Fax Manual Reception] key that appears.
 When a call is answered by touching the [Speaker] key, you will be able to hear the other party, however, you will not be 
able to speak.
 Even when you use an extension phone to answer a call, you can touch the [Fax Manual Reception] key in the touch panel 
to begin fax reception. You can also use the extension phone to begin fax reception.
☞RECEIVING A FAX AFTER ANSWERING A CALL ON THE EXTENSION PHONE (Remote Reception) (page 4-127)
AutoAuto
AutoSpeaker Volume
USB Mem. ScanFax
Special Modes
Resolution
Exposure
Original
Scan
Standard
Fax Memory:100%
SpeakerTelephone mode.Resend
Fax Manual
Reception
Internet FaxPC Scan
Scan:Send:Address Book
Address Review
File
Quick File 
						

							4-62
FACSIMILE
Contents
PRINTING A PASSWORD-PROTECTED FAX 
(Hold Setting For Received Data Print)
Hold Setting for Received Data Print can be enabled in the system settings (administrator) to have faxes received to 
memory without being printed. To print the faxes, a password must be entered. When this function is used, a password 
entry screen appears in the touch panel when a fax is received.
When the previously programmed 4-digit password is entered with the numeric keys, printing begins.
The [Cancel] key can be touched to close the password entry screen. If this is done, the data in memory key () will 
blink in the touch panel. The password entry screen will reappear when you touch the blinking key () or change 
modes.
When Received Data Image Check Setting is enabled in the system settings (administrator), a password can be 
entered to display the received data list screen. If you wish to check an image before printing it, continue from step 2 on 
the next page.
 The received faxes will be retained in memory regardless of whether they were received automatically or manually.
 If Fax Data Receive/Forward is executed in the system settings to forward received faxes to another machine, faxes 
retained in memory will also be forwarded. At that time, the same password entry screen as for printing will appear. 
Forwarding will not take place unless the password is entered.
System Settings (Administrator): Hold Setting for Received Data Print
Enable this setting to have received faxes retained in memory until a password is entered. This setting is also used to 
program the password.
Received data is stored.
Enter password via the 10-key.
Cancel 
						

							4-63
FACSIMILE
Contents
CHECKING THE IMAGE BEFORE PRINTING
This function requires the hard disk drive.
When Received Data Image Check Setting is enabled* in the system settings (administrator), you can check a 
received image in the touch panel before printing it out. When this function is enabled, follow the steps below to print a 
received image.
* The factory default setting is disabled.
Depending on the size of the received data, part of the image in the image check screen on the touch panel may not appear.
1
When an image is received, a 
confirmation prompt will appear. Touch 
the [Yes] key.
If this message appears while you are configuring settings of 
any type and you touch the [Yes] key, the settings that you are 
configuring will be cancelled. If this message appears in 
another mode, you will return to the base screen of image send 
mode after checking the image.
2
Select the received image
(1) Touch the key of the received image that 
you want to check.
Multiple received images can be checked.
(2) Touch the [Image Check] key.
 To show thumbnails of the received images, touch the 
[Thumbnail] key.
 To delete an image that has been selected, touch the 
[Delete] key. To print an image that has been selected, 
touch the [Print] key.
3
Check the received image and then 
touch the [Print] key.
Printing begins.
For information on the image check screen, see IMAGE 
CHECK SCREEN (page 4-66).
If the screen of step 1 appears when you are configuring settings in the setting screens of any of the modes, the configured 
settings will be cancelled if you view the image. After viewing the image, you will return to the base screen of image send 
mode, regardless of which mode you were in previously.
System Settings (Administrator): Received Data Image Check Setting
Use this to specify whether or not a received fax can be viewed before it is printed.
YesNo
The memory has received data.
Check the data?
Received Data ListBack
Not checked10:28
04/04/2010
04/04/2010
BBB BBB0612345678
BBB BBB
CCC CCC
0123456789
9876543210
BBB BBB
0123456789
1
5
ThumbnailSelect All
04/04/2010
04/04/2010
04/04/2010
04/04/2010
10:14
10:12
10:08
10:00
10:00
Not checked
Not checked
Checked
Checked
Checked
Image CheckDeleteForwardPrint
(1)
(2)
Image CheckBack
Display Rotation
Print
1 / 3012345678904/04/201010:28
/00100001 
						

							4-64
FACSIMILE
Contents
CHECKING THE IMAGE BEFORE 
FORWARDING
This function requires the hard disk drive.
When Received Data Image Check Setting is enabledin the system settings (administrator), you can select the 
received data from the list and forward it to the addresses recorded in the address book. When this function is enabled, 
follow the steps below to forward the received image.
* The factory default setting is disabled.
Depending on the size of the received data, part of the image in the image check screen on the touch panel may not appear.
1
When an image is received, a 
confirmation prompt will appear. Touch 
the [Yes] key.
If this message appears while you are configuring settings of 
any type and you touch the [Yes] key, the settings that you are 
configuring will be cancelled. If this message appears in 
another mode, you will return to the base screen of image send 
mode after checking the image.
2
Select the received image
(1) Touch the key of the received image that 
you want to check.
Multiple received images can be checked.
(2) Touch the [Forward] key.
 To show thumbnails of the received images, touch the 
[Thumbnail] key.
 To check a receieved image, touch the [Image Check] 
key.
☞IMAGE CHECK SCREEN (Page 4-66)
3
Touch the Forward Destination from the 
address book to select it.
Multiple forwarding addresses can be checked.
YesNo
The memory has received data.
Check the data?
Received Data ListBack
Not checked10:28
04/04/2010
04/04/2010
BBB BBB0612345678
BBB BBB
CCC CCC
0123456789
9876543210
BBB BBB
0123456789
1
5
ThumbnailSelect All
04/04/2010
04/04/2010
04/04/2010
04/04/2010
10:14
10:12
10:08
10:00
10:00
Not checked
Not checked
Checked
Checked
Checked
Image CheckDeleteForwardPrint
(1)
(2)
III III
GGG GGG
EEE EEE
CCC CCC
AAA AAA
JJJ JJJ
HHH HHH
FFF FFF
DDD DDD
BBB BBB12
51510
Address Review
ToCc
ABCDFreq.EFGHIJKLMNOPQRSTUVWXYZetc.
Start forward.Sort Address 
						

							4-65
FACSIMILE
Contents
4
Start forward
Touch the [Start forward.] key.
If the screen of step 1 appears when you are configuring settings in the setting screens of any of the modes, the configured 
settings will be cancelled if you view the image. After viewing the image, you will return to the base screen of image send 
mode, regardless of which mode you were in previously.
System Settings (Administrator): Received Data Image Check Setting
Use this to specify whether or not a received Internet fax can be viewed before it is printed.
III III
GGG GGG
EEE EEE
CCC CCC
AAA AAA
JJJ JJJ
HHH HHH
FFF FFF
DDD DDD
BBB BBB
ToCc
12
51510
Address Review
ABCDFreq.EFGHIJKLMNOPQRSTUVWXYZetc.
Sort AddressStart forward. 
						

							4-66
FACSIMILE
Contents
IMAGE CHECK SCREEN
This function requires the hard disk drive.
This section explains the image check screen.
(1) Information display
This shows information on the displayed image.
(2) Preview image
An image of the selected received image appears.
If the image is cut off, use the scroll bars at the right and 
bottom of the screen to scroll the image. Touch a bar and 
slide it to scroll. (You can also touch the   keys to 
scroll.)
(3) Change page keys
When there are multiple pages, use these keys to 
change pages.
  keys:  Go to the first or the last page.
  keys:  Go to the previous page or the next 
page.
 Page number display: This shows the total number of 
pages and the current page 
number. You can touch the 
current page number key and 
enter a number with the 
numeric keys to go to that page 
number.(4) Display Rotation key
This rotates the image right or left by 90 degrees. The 
rotation applies to all pages in the file, not just the 
displayed page.
(5) [Print] key
Touch to start printing.
(6) Display zoom key
Use this to set the zoom ratio of the displayed image. 
Changes from the left in the order Full Page, Twice,  
4 Times, 8 Times. The setting applies to all pages in 
the file, not just the displayed page.
(7) Image select key
When multiple images are selected for preview display, 
use this to change the displayed images.
0123456789
Image Check
04/04/2010  10:281 / 3
Display Rotation
Print
Back
00010010
(3)(5)(1) (2)(4)(7)(6)
A preview image is an image for display on the touch panel. It will differ from the actual print result.