Sharp Mx2310u User Guide
Have a look at the manual Sharp Mx2310u User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 615 Sharp manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 89
1-48
BEFORE USING THE MACHINE
Contents
If login fails
If the login screen fails to appear or the application does not operate correctly, the machine may also stop operating
correctly. In this event, it is recommended that you quit external account mode from the Web pages of the machine. For
more information, see [Help] in the Web pages.
If it is necessary to forcibly terminate external account mode using the operation panel of the machine, follow the steps
below.
Press the [SYSTEM SETTINGS] key and...](http://img.usermanuals.tech/thumb/68/103099/w64_mx2310u-user-guide-1512492901_d-88.png "Page 89
1-48
BEFORE USING THE MACHINE
Contents
If login fails
If the login screen fails to appear or the application does not operate correctly, the machine may also stop operating
correctly. In this event, it is recommended that you quit external account mode from the Web pages of the machine. For
more information, see [Help] in the Web pages.
If it is necessary to forcibly terminate external account mode using the operation panel of the machine, follow the steps
below.
Press the [SYSTEM SETTINGS] key and...")
1-50 BEFORE USING THE MACHINE Contents 1 Open the automatic document feeder and remove the glass cleaner. 2 Clean the document scanning area on the document glass with the glass cleaner. 3 Replace the glass cleaner.
1-51 BEFORE USING THE MACHINE Contents CLEANING THE MAIN CHARGER OF THE PHOTOCONDUCTIVE DRUM If black lines or coloured lines appear even after you have cleaned the document glass and automatic document feeder, use the charger cleaner to clean the main charger that charges the drum. 1 Open the front cover. 2 Release the waste toner box. Move the lock of the waste toner box to the release position. Release the lock of the waste toner box and let it fall forward as far as it will go as shown in the figure. 3 Remove the waste toner box. Hold the box by both hands and lift it up slowly. If the waste toner box falls too far forward, it will not be possible to remove it. (Remove the box when it is at an angle of about 30 degrees.)
1-52 BEFORE USING THE MACHINE Contents 4 Remove the charger cleaner The charger cleaner is attached to the front cover of the machine. (1) Unfasten it from the claw by pressing the right side of the charger cleaner. (2) Place it in the front spread across the top of the claw. (3) Unfasten the charger cleaner rotating around the boss from the claw on the left side. 5 Clean the main charger. (1) Gently push the charger cleaner all the way in. (2) Gently pull the charger cleaner out. Insert so that the cleaning location label (A) and the charger cleaner label (B) are oriented as shown. 6 Repeat step 4 with each of the other main chargers. There are a total of 4 places to be cleaned in the machine as shown. (2) (1) (3)Boss (B)(B) (A) Main charger
1-53 BEFORE USING THE MACHINE Contents 7 Replace the charger cleaner in its original position. (1) Rotate the charger cleaner after putting it on the boss and hook its edge (the side that does not have a handle) to the claw on the left side. (2) Place the right-hand side of the charger cleaner on the inner side, spread across the top of the claw. (3) Hook the charger cleaner to the claw. 8 Mount the waste toner box. Insert it in a direction slanting from the top towards the bottom. (A direction opposite to that at the time of mounting it.) 9 Push the waste toner box into the machine. Push the waste toner box firmly in until it clicks into place. 10 Lock the waste toner box. Move the lock of the waste toner box to the lock position. 11 Close the front cover. If this does not solve the problem, pull the knob out and push it back in 3 more times. When pulling and pushing the knob to clean the charger, pull and push the knob slowly from one end to the other. (1)Boss (2) (3)
1-54 BEFORE USING THE MACHINE Contents CLEANING THE PT CHARGER OF THE PRIMARY TRANSFER BELT If black lines or coloured lines appear even after you have cleaned the document glass, automatic document feeder and the main charger, use the PT charger cleaner to clean the PT charger. 1 Open the front cover. 2 Release the lock of the waste toner box. Move the lock of the waste toner box to the release position. Release the lock of the waste toner box and let it fall forward as far as it will go as shown in the figure. 3 Remove the waste toner box. Hold the box by both hands and lift it up slowly. If the waste toner box falls too far forward, it will not be possible to remove it. (Remove the box when it is at an angle of about 30 degrees.) 4 Clean the PT charger (1) Slowly pull out the PT charger cleaner till a point where it offers resistance. (2) Slowly push the PT charger cleaner back till the end. (3) Repeat the steps (1) and (2) three times.
1-55 BEFORE USING THE MACHINE Contents 5 Mount the waste toner box. Insert it in a direction slanting from the top towards the bottom. (A direction opposite to that at the time of mounting it.) 6 Push the waste toner box in till the innermost point. Push it in until it clicks into place. 7 Lock the waste toner box. Move the lock of the waste toner box to the lock position. 8 Close the front cover.
1-56 BEFORE USING THE MACHINE Contents CLEANING THE BYPASS FEED ROLLER If paper misfeeds frequently occur when feeding envelopes or heavy paper through the bypass tray, wipe the surface of the feed roller with a clean soft cloth moistened with water or a neutral detergent. CLEANING THE ORIGINAL FEED ROLLER If lines or other dirt appear on the scanned original when the automatic document feeder is used, wipe the surface of the roller with a clean soft cloth moistened with water or a neutral detergent.
1-57 BEFORE USING THE MACHINE Contents CLEANING THE LASER UNIT When the laser unit inside the machine becomes dirty, line patterns (coloured lines) may form in the printed image. Identifying lines (coloured lines) caused by a dirty laser unit Coloured lines always appear in the same place. (The lines are never black.) The coloured lines are parallel to the direction of paper feeding. Coloured lines appear not only on copies but also on print jobs from a computer. (The same lines appear on both copies and print jobs.) If the above problems occur, follow the steps below to clean the laser unit. 1 Open the front cover. 2 Take out the cleaning tool for the laser unit. The cleaning tool is attached to the front cover. (1) Pull the right side of the cleaning instrument and unfasten it from the claw. (2) Place it in the front spread across the top of the claw. (3) Unfasten the cleaning instrument rotating around the boss from the claw on the left side. 3 Make sure that the cleaner at the tip of the cleaning tool is not dirty. If the cleaner is dirty, remove the cleaner and replace it with a clean one. For the procedure for replacing the cleaner, see steps 4 through 6. If the cleaner is not dirty, go to step 7. (2) (1) (3) Boss Cleaner
1-58 BEFORE USING THE MACHINE Contents 4 Open the inner cover and take out a replacement cleaner. Replacement cleaners are stored on the inner cover. Grasp the end of the cleaner and pull it out of the cover. 5 Remove the dirty cleaner from the tip of the cleaning tool. (1) Firmly grasp the tool close to where the cleaner is attached. (2) Use your other hand to press down on the hook that secures the cleaner and remove the cleaner. Put the removed cleaner back on the inner cover. After replacing the cleaner, be sure to close the inner cover. 6 Attach the new cleaner to the cleaning tool. (1) Align the cleaner hook with the attachment hole in the cleaning tool. (2) Hold the cleaner firmly and push the cleaning tool in.
1-59 BEFORE USING THE MACHINE Contents 7 Clean the laser unit. (1) Point the cleaner down and slowly insert the tool into the hole that you wish to clean. Be sure to point the cleaner down. Labels similar to (A) are attached to areas that require cleaning. (2) Insert the cleaning tool all the way into the hole and then pull it back out. Pull the cleaning tool out until you feel the tip of the tool leave the cleaning surface of the laser unit. (3) Repeat step (2) two or three times and then remove the cleaning tool. 8 Repeat step 7 to clean all holes in the laser unit (4 holes). There are a total of 4 holes to be cleaned in the laser unit, including the hole cleaned in step 7. Clean all holes. (A) Holes to be cleaned