Home > Panasonic > Communications System > Panasonic Digital Business System Section 300 Installation Guide

Panasonic Digital Business System Section 300 Installation Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Panasonic Digital Business System Section 300 Installation Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 790
    							Section 400 FFl 
    Issue 2 July 1993 DBS Programming Instructions 
    CPC-A / 3.0. CPC-B / 2.0 / 3.0 / 4.0 
    f 
    Determines whether Tl channels are used 
    The robbed bit setting determines lfAJ3CD 
    as outgoing only, or bothway. 
    signaling is used. ABCD signaling robs bits 
    ~ from the Tl channels and uses those bits to 
    ..:“.$;, 
    transmit signaling information. 
    O=Bothwav 
    l=Outgoing only 
    cw3 
    --::~~ 
    O=Off (ABCD signaling is not used.) 
    ~~~ 
    l=On @BCD signaling is used.) 
    .:‘i~~~~~~ 
    #@ggy$:: 
    For changes to this parameter to take effect, ~~~ ~ 
    the system must be powered down, then For changes 
    to this parameterto take effect, 
    back up. 
    the system must be powered down, then 
    back up. 
    f-- 
    80  
    						
    							DBS Programming Instn~ctions 
    Section 400 FFl 
    WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
    Issue 3 July 1993 
    Determines whether the system expects DP ‘hnsmits dial tone hm the Tl channel to 
    or DTMF digits for incoming DID or DNIS another DBS within a private network. 
    calls. 
    If YXIVIF” is selected, the DBS must be 
    c- ) equipped with an MFR card. 
    81  
    						
    							Section 400 FFl 
    Issue 2 July 1993 DBS Programming Instructions 
    WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
    lbrmn.its busy tone from theT1 channel to lhnsmits dial tone from the Tl channel to 
    another DBS within a private network. DBS stations. 
    o=off 
    l=On o=m 
    l=On 
    c 
    82  
    						
    							DBS Programming Instructiona 
    WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
    Transmits ringback tone f?om theT1 chan- 
    nel to the central office 
    within a private network. or another DBS 
    o=off 
    l=On 
    section 400 FFl 
    Issut% 3 July 1993 
    Associates a dialed number with a station. 
    Associatesafour-digitdialednumberwitha 
    station number. DNIS is available onlywith 
    theT1 Interface. 
    Stations are numbered using one of two 
    patterns: 10-69 or 100-699. 
    83  
    						
    							Section 400 
    FF2 
    DBS 
    Issue 3 July 
    1993 Programming Instructions 
    WC-A / 3.0. CPC-B / 2.0 
    / 3.0 / 4.0 
    To set a central o&e line in service, or to 
    remove it from service, this option must be 
    used. To set a central office line for touch-tone or 
    pulse dialing. (10 pulses per second), this 
    option must be used. 
    To set any central office line in service. 
    enter: To set any central office line for touch tone 
    dialing, enter: 
    ,lDBSl.ine~ort numbed#.l#.OW 1. rDBs Iine Dolt mmbex~#. 2#. on 
    To remove any central ofllce line from 
    service, enter: To set any centml o&e line for pulse 
    dialing, enter: 
    [FF2l,@BSlineportnumber)#,1#,1# CPllrZ),@BSlineportnumber)#,2#, l# 
    / 
    A steady, red LED on any FF key 
    programmed as a line key, indicates 
    If a central office line is removed from 
    service, a new caller to that line will  an out-of-service line. 
    hear a ring, but the DBS user will never 
    be aware of the caller because ring 
    assignments for the line will not function. If the central office line port is designated 
    as a ground start line (FF2]-(1-64-21)1 it  If a central oflice line port is used for a 
    is imperative that the 48 volt external 
    power supply be properly connected to  door-box adapter sensor, set the port for 
    the terminals on the DBS backplane. 
    Misconnection of this power supply  pulse dialing. 
    can result in serious damage to the 
    DBS main cabinet. See DBS In&all&on 
    Instructions manual (section 300). and 
    Technote 1 (March 1991). for further 
    information. 
    The j-lash and redial features will not 
    operate if a line has been designated as 
    “ground start*. See technote 13 (March 
    1992) for further information. 
    84  
    						
    							DBS Programming Instructions 
    CPC-A / 3.0 WC-B / 2.0 / 3.0 / 4.0 
    I 
    / 
     
     
    Section 400 FF2 
    Issue 3 July 1993 
    To place a central office line in a group so 
    that it can be one of many that can be 
    automatically chosen for outbound 
    dialing, this option must be used. 
    When dialing a “9” from an SLT or 
    digital extension, or pressing an FF 
    key that is set as a pooled trunk key, 
    any available line in the group will be 
    accessed. 
    To not include a central office line to be a 
    member of the “9” access group, enter: 
    .- .: 
    ,i 
    ~),@BSIlneportnumber)#,3#,0# 
    To set any central office line to be ‘a 
    member ofthe “9” access group, enter: 
    .IDBSline~ort number)#.3#.1# 
    n. 
    @gJgg’i 
    :..- .i.,.i,.,., . ..e 
    Set FFl option “LCR Access” for “Pooled 
    Trunk Access” cdl. If this option is set for 
    “LCRAccess”, central o&e line selection 
    will default to pooled central office line 
    access group 9, if all lines that could be 
    used for “ICR Access” are busy. 
    The line selection is made from the 
    highest line number in the group, to the 
    lowest line number in the group. To place a central office line in a 
    group so that it can be one of many 
    that can be automatically chosen for 
    outbound dialing, this option must 
    be used. When dialing an 
    “81, 82.83, 
    84, 85 or 86” from ‘an SLT or digital 
    extension. or pressing an FF key that is 
    set as a multiple central office (MCO) 
    line key, any available line in the group 
    wilI be accessed. 
    To set any central office line to be a 
    member of the “81” access group, enter: 
    -: 
    ~],@BSIlneportnumber)#,4#,1# 
    -To ‘set- any central office line to be a 
    member of the ?82” access group, enter: 
    To set any central office line to be a 
    member of the 333” access group, enter: 
    To set any central office line to be a 
    member of the “84” access group, enter: 
    To set any central office line to be a 
    member of the “85” access group. enter: 
    @FZJ,(DBSlineport 
    number)#,8#,1# 
    85  
    						
    							Section 400 FF2 
    Issue 3 July 1993 
    To set any central office line to be a 
    member of the “86” access group, enter: 
    [eez], (DBS line port number)#, 9#, l# 
    To remove any central office line &om any 
    access group (81 through 86), enter: 
    1. (DBS line Mlrt numberld. (49lW, 
    06 
    The same trunks may appear in more 
    than one line access group and include 
    access group 9. 
    The line selection in a particular group is 
    madef+omthehighestavailablelinenumber 
    to the lowest available line number. 
    DBS Programxdq Ix~tructiona 
    WC-A 
    / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
    Each central of&e line port must be 
    identified as a regular central o!IIce line, or 
    PBX line. 
    To set the central of&e line type to central 
    offke, enter: 
    1.KBSl.ineportnumber)#. 1OW. l# 
    To set the central of&e line type to PBX, 
    enter: 
    Toll restriction settings can be affected by 
    this setting. 
    lf a central o&e line port is used for a 
    door-box adapter sensor, set the port for 
    pulse dialing. 
    Ifthe central office line port is designated 
    as a ground start line [FF2]-21#. it is 
    imperative that the 48 volt external power 
    supply be properly connected to the 
    terminals on the DBS backplane. 
    nnection of this power supply 
    aznmsuZtinsedusdamagetothe 
    DBsmainctlbheL 
    See DBSlnstallation Instructions manual 
    (section 300). and Technote 1 (March 
    1991). for further i.nformation.  
    						
    							DBS Programming Inst.ructions 
    WC-A / 3.0 CPC-B / 2.0 / 3.0 / 4.0 
    i Section 400 FF2 
    Issue 3 July 1993 
    To set acentral office Iine(s) to automaticaRy 
    provide DiSAtone upon connection with an 
    inbound cakr. this option must be set 
    To set any central office line to provide a 
    DISA tone when connected to a new 
    inbound caller, enter: 
    ~],@BSlinep0rtnumher)#, ll#, l# 
    To ‘set any central of& I&e so that it does 
    not provide a DISA tone when connected 
    to a new inbound caller, enter: 
    l.lDBSline~ortnumberM. ll#.O# 
    To set automatic DISA start and end 
    times, see [FIG?] 19#. and 20# program 
    addresses, and the DISA code program 
    address at [FFl], 6#. Any extension can be set with a private 
    centml ofIke line(s). A number of private 
    lines can belong to one extension, but 
    the same private line cannot be set on 
    multiple extensions. 
    To set extension port 15 for central office 
    Iine 12 to be a private central of&e I.i.ne(s), 
    enter: 
    pF2], lS#, 12#, 12# 
    To reset anv extension to the default 
    initialized 
    ~rh&e he value. Dress IFI%?L 
    @BS line oort number)#. 12#. ICONFZ, 
    JON/OFl?l. 
    Anincom.ingcalIonaprivateIinewiIlonIy 
    ring on one extension. 
    Once the private line option is set, other. 
    extensions cannot make outbound calls 
    or receive inbound caIls on that line. 
    Ifthe private Iine setting is disabled, caIIs 
    cannot be made or received on that line(s) 
    without manualIy reprogrammingthe toil 
    restriction options of an extension(s) to 
    which the line should now appear. 
    In DBS instaIlations using the WC-A 
    card, the highest extension port number 
    that can be used is 72. 
    87  
    						
    							Section 400 FF2 
    Issue 3 July 1993 DBS Programming Instructions 
    WC-A / 3.0, CPC-B / 2.0 / 3.0 / 4.0 
    To set an automatic pause during dialing 
    on a central of&e line defined as PBX this 
    option must be used. 
    To set the automatic pause on line 15 for 
    example, (once line 15 is defined as a 
    PBX). enter: 
    pm. SW. 13w. 19 
    To disable the automatic pause on line 12 
    for example. (once line 12 is defI.txd as a 
    PBX), enter: 
    pF2], 128, 136, ow 
    See [FFl], 3.# 12# program option, for the 
    timer used for this pause. 
    To define whether dialed digits will be 
    outpulsed after dial tone has been 
    detected, or not, this option is used. 
    To outpulse dialed digits only after dial 
    tone is detected, enter: 
    1,fDB!3liDeDOrtnumber~u. 141y.on 
    To outpulse dialed digits according to the 
    system dial pause timer, enter: lfthis option is not set, the dialed number 
    is outpulsed according to the system dial 
    pause time. 
    To increase the duration of the MMF 
    signal when making an outbound call, 
    use this feature. 
    c 
    To set the on/off duration of an 
    outbound 
    IXMF signal to 75 ms. on and sd’ms.‘tAT. 
    enter: 
    1.nlBSliDeDortllDmber~#. 15#.1# 
    To set the on,!off duration of an outbound . 
    M’MF signal to 125 ms. on and 125 ms. 
    off. enter: 
    PW2],(DBSlineportnumber)#, 15#,2# 
    To set the on/off duration of an outbound 
    MMF signal to 250 111s. on and 250 ms. 
    off, enter: 
    lFF2], (DBSlineportnumber)#, 15#, 3W 
    fFF2],@ESlineportnumber)#, 14#, 111 
    88  
    						
    							DBS Programming Instructions 
    WC-A 
    / 3.0 WC-B / 2.0 / 3.0 / 4.0 Section 400 FF2 
    Issue 3 July 1993 
    To allow a central ofike line(s) to be able to 
    be used in an unsupervised conference 
    call, this feature is used. 
    To disable line 22, for (xample, so that it 
    cannot be used in aline to line conference, 
    enter: 
    JFKBl. 22#. 16W. OW 
    To set line 22 to be able to be used as one 
    of the lines in a line to he conference. 
    enter:. 
    c ‘> m], 22W. 16#, l# 
    See [FF3], 13# program address to start a 
    conference call. 
    A conferenced call will be disconnected if 
    the call go& beyond the time set in 
    unsupervised conference timer. The ring pattem of each central oflice line 
    can be set in one of nine patterns to 
    provide easy recognition of different lines. 
    - MI lon/3off 1 
    I I 1# 3on/loff 
    I I  6# 5 OKl/.5Off I 
    I I  2# 2on/2off ?I# 
    1 I 5 on I.5 off 1.5 onf2J Off I 
    I I  Y lon/lon 
    I I  8# 5 onl3.5off 
    I 
    I I  4# 1 on/2off 
    I I  9# lon/7off 
    I 
    There is no change in the ring pattern for 
    transferred calls. 
    89  
    						
    All Panasonic manuals Comments (0)

    Related Manuals for Panasonic Digital Business System Section 300 Installation Guide