NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 5 4
Revision 2.0
ATTENDANT CONSOLE (SN610): CALL QUEUING
PROGRAMMING 
Refer to CALL WAITING DISPLAY. 
						

							ND-45670 (E) CHAPTER 2
Page 55
Revision 2.0
ATTENDANT CONSOLE (SN610): CALL SPLITTING
PROGRAMMING
DESCRIPTION DATA
Assign the SRC, DEST, TALK, and CANCEL 
keys on the SN610 ATTCON.
If no data is set, the default setting is as 
follows:  
Note:TALK key is assigned as a Multi-
Function key, during the answer state.• YY = 00
(1) ATTCON No. +   + Key No. 
(2) F6200:  SRC
F6201:  DEST 
F6202:  CANCEL 
F6203:  TALK 
START
END
CM90
Key No.DataDescription
06 F6203 Talk (TALK) Note
19 F6200 Source (SRC) 
20 F6201 Destination (DEST) 
24 F6202 Cancel (CANCEL)
LO O P1LOOP2LOOP3LOOP4LOOP5LO O P6
01
AN S
25RLS
26
123
456
78 9
*0#SRC DEST
H O LD C ANC EL
13 14
15 16
17 1819 20
21 22
23 24
07
0203040506
08
09101112
AB C D E F
JKL M N O GHI
TU V W X Y PRS
OPER
, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 5 6
Revision 2.0
ATTENDANT CONSOLE (SN610): CALL WAITING DISPLAY
PROGRAMMING
DESCRIPTION DATA
Specify the number of waiting calls which 
cause the Call Waiting lamp to flash. (1) 00
(2) No. of Waiting Calls (01-48)
If no data is set, the default setting is 6.
END
CM42 START 
						

							ND-45670 (E) CHAPTER 2
Page 57
Revision 2.0
ATTENDANT CONSOLE (SN610): COMMON ROUTE INDIAL
PROGRAMMING
DESCRIPTION DATA
Provide the system with Diversion Display. (1) 204 
(2) 0:  To be provided
Assign the required number of LDN keys on 
the SN610 ATTCON. • YY = 00
(1) SN610 ATTCON No. +   + Key No.
(2) F6000:  LDN0 
F6007:  LDN7 
Assign the indialed number to each LDN key 
assigned by CM90. The indialed number 
should be different from any numbers 
assigned by CM10 and CM11. • YY = 01
(1) 1-8: LDN key No. (00-07) assigned by 
CM90.
(2) X-XXXX (Indialed No.) 
Assign the destination to which a DID Call is 
transferred when an unassigned number is 
dialed.• YY = 06 (On DID Call) 
(1) Tenant No. (00-63)
(2) X-XXXX (Station No.)
E000:  SN610 ATTCON
END
CM08 START
CM90
CM50
CM51,
|| 
						

							CHAPTER 2 ND-45670 (E)
Pag e 5 8
Revision 2.0
ATTENDANT CONSOLE (SN610): COMMON ROUTE INDIAL
To provide the LDN Diversion feature, the following programming is also required.
DESCRIPTION DATA
Provide the system with the LDN Diversion 
feature.(1) 205 
(2) 0:  To be provided 
Assign the data for LDN Diversion to each 
indialed No. assigned by CM50 YY = 01. • YY = 00 (Tenant No. of the LDN)
(1) 01-08:  LDN0-7 assigned by CM50 YY 
= 01. 
(2) Tenant No. (00-63)
• YY = 01 (TAS Group No.)
(1) Same as YY = 00 
(2) TAS Group No. (00-63)
Note:A call is diverted to LDN0-7 keys as
specified by CM58 YY = 02-07, even
if CM50 YY = 01, 1-8 has been set.• YY = 02 (Day Mode Destination of the 
LDN) 
(1) Same as YY = 00 
(2) 00:  LDN0 key 
07:  LDN7 key 
08:  To TAS
09: To the station assigned by CM58 
YY = 08.
• YY = 03 (Night Mode Destination) 
(1) Same as YY = 00
(2) 00:  LDN0 key
07:  LDN7 key
08:  To TAS
09: To the station assigned by CM58 
YY = 09.
• YY = 04 (Day mode diversion for busy 
destination station) 
(1) Same as YY = 00 
(2) 00:  To ATTCON (BUSY key) 
08:  To TAS
09:  Camped on 
CM08
CM58 START
A||
|| 
						

							ND-45670 (E) CHAPTER 2
Page 59
Revision 2.0
ATTENDANT CONSOLE (SN610): COMMON ROUTE INDIAL
HARDWARE REQUIRED 
PN-AUCA card (DID Trunk)
DESCRIPTION DATA
• YY = 05 (Night mode diversion for busy 
destination station) 
(1) Same as YY = 00 
(2) Same as YY = 04 
• YY =06 (Day mode diversion for non-an-
swering destination station) 
(1) Same as YY = 00 
(2) 00:  To ATTCON (NANS key) 
08:  To TAS
• YY = 07 (Night mode diversion for non-
answering destination station) 
(1) Same as YY = 00 
(2) Same as YY = 06 
If a station is designated by YY = 02, 03, 
assign the station number to which the call is 
to be diverted. • YY = 08 (Day mode destination station) 
(1) Same as YY = 00 
(2) X-XXXX (Station No.)
• YY = 09 (Night mode destination sta-
tion) 
(1) Same as YY = 00 
(2) X-XXXX (Station No.)
END
A
CM58 
						

							CHAPTER 2 ND-45670 (E)
Pag e 6 0
Revision 2.0
ATTENDANT CONSOLE (SN610): DIALED NUMBER IDENTIFICATION SERVICE (DNIS)
(1300 Series Enhancement)
PROGRAMMING
DESCRIPTION DATA
Provide the system with Diversion Display. (1) 204
(2) 0:To be provided
Specify the Incoming Call Identification (ICI) 
key to which each LDN call or Tie Line call 
from each trunk route will terminate.• YY=15
(1) Trunk Route No. (00-63)
(2) 00: C.O. Incoming Call 0
07: C.O. Incoming Call 7
40: Tie Line Incoming Call 0
47: Tie Line Incoming Call 7
Assign the ICI key required number of LDN 
to ICI keys.• YY=00
(1) Attendant Console No. +   + Key No.
(2) F6000-F6007 (C.O. Incoming Call 0-7)
F6040-F6047 (Tie Line Incoming Call 0-
7)
Assign the indialed number to each LDN key 
or Tie Line key assigned by CM90. The 
indialed number should be different from any 
numbers assigned by CM10 and CM11.• YY=01 (For DID)
(1) 0: Effective data in CM35, YY=15
1-8: LDN key No. (0-7) assigned by 
CM90
(2) X-XXXX (Indialed No.)
• YY=02 (For Tie Line)
(1) 0: Effective data in CM35, YY=15
1-8: Tie Line key No. (0-7) assigned by 
CM90.
(2) X-XXXX (Indialed No.)
CM90
CM50 START
A
CM08
CM35
~
~
~
~
, 
						

							ND-45670 (E) CHAPTER 2
Page 61
Revision 2.0
ATTENDANT CONSOLE (SN610): DIALED NUMBER IDENTIFICATION SERVICE (DNIS)
(1300 Series Enhancement)
DESCRIPTION DATA
Tenant Number of the LDN assigned by 
CM50-1.• YY=00
(1) 00:  Effective data in CM35, YY=15
01-08: LDN Key No. assigned CM90.
(2) 00-63:Tenant 00
Tenant 63
Assign desired company name to each LDN/
Tie Line key number assigned by CM90.• YY=10
(1) 00:  Effective data in CM35, YY=15
01-08: LDN key No. (0-7)
10: Effective data in CM35, YY=15
11-18: Tie Line key No. (0-7) 
(2) Character Code 
(20-5F: See Character Code Table at-
tached)
MAX: 8 digitsCM58
A
END
~ 
						

							CHAPTER 2 ND-45670 (E)
Pag e 6 2
Revision 2.0
ATTENDANT CONSOLE (SN610): DIALED NUMBER IDENTIFICATION SERVICE (DNIS)
(1300 Series Enhancement)
To provide the LDN Diversion feature, the following programming is also required.
DESCRIPTION DATA
Provide the system with LDN Diversion 
feature.(1) 205
(2) 0: To be provided
Assign the data for LDN Diversion to each 
indialed number assigned by CM50, YY=01.
Note that a call is diverted to LDN 0-7 keys as 
specified by CM58, YY=02, YY=03, even if 
CM50, YY=01, 1-8 has already been set.• YY=02 (Day Mode Destination of the 
LDN)
(1) 00: Effective data in CM35, YY=15
01-08:  LDN key No. (0-7) assigned by 
CM90.
00: Effective data in CM35, YY=15
01-08: Tie Line key No. (0-7) assigned 
by CM90
(2) 00:LDN/TIE Line key 0
07: LDN/TIE Line key 7
• YY=03 (Night Mode destination)
(1) Same as YY=02
(2) 00: LDN/TIE Line key 0
07: LDN/TIE Line key 7
• YY=08 (Day Mode destination station)
(1) Same as YY=02
(2) X-XXXX (Station No.)
• YY=09 (Night Mode destination station)
(1) Same as YY=02
(2) X-XXXX (Station No.)
Assign desired company name to each LDN/
Tie Line key number assigned by CM90.• YY=10
(1) 00: Effective data in CM35, YY=15
01-08:  LDN key No. (0-7)
10: Effective data in CM35, YY=15
11-18:  Tie Line key No. (0-7)
(2) Character Code
(20-5F: See the table below)
Max. 8 digitCM08
CM58
END
START
~
~
~
~ 
						

							ND-45670 (E) CHAPTER 2
Page 63
Revision 2.0
ATTENDANT CONSOLE (SN610): DIALED NUMBER IDENTIFICATION SERVICE (DNIS)
(1300 Series Enhancement)
HARDARE REQUIRED
PN -4DIT card (DID Trunk)
PN-2ODT card (Tie Line Trunk)
Character Code Table
Character DATA Character DATA Character DATA Character DATA Character DATA Character DATA Character DATA
(space)20 * 2A 4 34 > 3E H 48 R 52´5C
! 21 + 2B 5 35 ? 3F I 49 S 53 ] 5D
“ 22 , 2C 6 36 @ 40 J 4A T 54 ^ 5E
# 23 - 2D 7 37 A 41 K 4B U 55 - 5F
$24 . 2E838B42L4C V56
% 25 / 2F 9 39 C 43 M 4D W 57
& 26 0 30 : 3A D 44 N 4E X 58
‘ 27 1 31 ; 3B E 45 O 4F Y 59
( 28 2 32 < 3C F 46 P 50 Z 5A
) 29 3 33 = 3D G 47 Q 51 [ 5B