NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 1 34
Revision 2.0
CALL FORWARDING: CALL FORWARDING-NO ANSWER
DESCRIPTION DATA
To apply this feature to incoming calls, set the 
trunk route combinations for Tandem 
Connection.
Note:For Resident System Programming,
refer to the Command Manual.• CM35 YY=05
(1) Trunk Route No. (00-63)
Note
(2) 1 : Release Signal arriveNote
• CM36
(1) Incoming Trunk Route No. + Outgoing 
Trunk Route No. (Assigned by CM35 
YY=05)
(2) 0: Allowed
Specify the setting method for Call 
Forwarding-No Answer-Outside.(1) 222
(2) 0: The feature is set when the station 
goes on hook/when receiving 
Service Set Tone (ORT time out)
1 : The feature is set when receiving 
Service Set Tone (ORT time out)
Assign whether or not an extention can set 
Call Forwarding-No Answer-Outside by 
entering only a trunk access code.(1) 386
(2) 0: Restrict
1 : Allow
Assign whether or not the system should 
check the trunk restriction class of the 
forwarded station during a Call Forwarding-
No Answer-Outside.(1) 387
(2) 0: Call forwarding No Answer-Outside 
follows setting station class
1 : No check
Assign Call Forwarding-No Answer keys to 
the Multiline Terminals, as required.• YY=00
(1) Primary Extension No. + + Key No.
(2) F0016: Call Forwarding-No Answer Set/
Cancel
For setting the same key as Call Forwarding-
Busy Line
(1) F0012: Set/Cancel
Provide Call Forwarding feature with each 
tenant as per incoming call type.• YY=23 (Internal Call or ATT assisted 
Call)
• YY=24 (C.O. Incoming Call)
• YY=25 (Tie Line Incoming Call)
(1) Tenant No. (00-63)
(2) 1 : Call Forwarding
A
CM08
CM65
CM35
CM36
CM90
END, 
						

							ND-45670 (E) CHAPTER 2
Page 135
Revision 2.0
CALL FORWARDING: CALL FORWARDING-DESTINATION
PROGRAMMING
DESCRIPTION DATA
Assign Service Restriction Class (A) to each 
station.• YY = 02
(1) X-XXXX: (Station No.)
(2) XX
XX
*a: Service Restriction Class (A)
(00-15 )
Assign this feature to Service Restriction 
Class (A) assigned by CM12 YY=02.•Y=15
(1) XX: Service Restriction Class (A) as-
signed by CM12 YY=02.
(2) 1 : Allowed
Assign the access code for Call Forwarding-
Destination, Entry and Cancellation, 
respectively.• YY=0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code (*7, #7)
(2) 018: Call Forwarding-Destination Entry
019: Call Forwarding-Destination Cancel
Assign Call Forwarding-Destination Set/
Cancel Keys to the Multiline Terminals, as 
required.• YY=0
(1) Primary Extension No. +  + Key No.
(2) P0018: Set
P0019: Cancel
END
CM12
CM15
CM20
CM90 START
*a
, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 36
Revision 2.0
CALL FORWARDING: MULTIPLE CALL FORWARDING-ALL CALLS
PROGRAMMING
In addition to the programming for Call Forwarding-All Calls, do the following programming.
DESCRIPTION DATA
Specify the number of times a call can be call 
forwarded.(1) 14
(2) 01-05 [Number of times (One to five 
times)]
If no data is set, the default setting is 5.CM42
END
START 
						

							ND-45670 (E) CHAPTER 2
Page 137
Revision 2.0
CALL FORWARDING: MULTIPLE CALL FORWARDING-BUSY LINE
PROGRAMMING
In addition to the programming for Call Forwarding-Busy Line, do the following programming.
DESCRIPTION DATA
Specify the number of times a call can be call 
forwarded.(1) 14
(2) 01-05 [Number of times (One to five 
times)]
If no data is set, the default setting is 5.CM42
END
START 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 38
Revision 2.0
CALL FORWARDING: MULTIPLE CALL FORWARDING-NO ANSWER
PROGRAMMING
In addition to the programming for Call Forwarding-No Answer, do the following programming.
DESCRIPTION DATA
Specify the timing for No Answer after 
second Call Forwarding.•Y = 0
(1) 46
(2) 01-30: 4 -120 sec. in 4 sec. increments
If no data is set, the default setting is 32-36
seconds.CM41
END
START 
						

							ND-45670 (E) CHAPTER 2
Page 139
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING - ALL CALLS
(1200 Series Enhancement)
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for this feature to 
the required stations.
Note:When providing Call Forwarding-All
Calls-Outside, set “1” (Allowed) for
YY=00, YY=26 of CM15• CM12 YY=02 
[Service Restriction Class (A) (00-
15 )]
• CM15 YY=00 (Call Forwarding-All
Calls)
• CM15 YY=26 (Call Forwarding-All
Calls-Outside)
(1) XX: Service Restriction Class (A) 
assigned by CM12 YY=02.
(2) 1 : Allowed
Assign the access code for Call Forwarding-
All Calls, Entry and Cancel, respectively.• Y=0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code (*5, #5)
(2) 010: Entry
011: Cancel
Assign the access code for Split Call 
Forwarding-All Calls.(1) X-XXX: Access Code
(2) A80: Entry
A81: Cancel
To apply this feature to incoming calls, set the 
trunk route combinations for Tandem 
Connection.• CM35 YY=05
(1) Trunk Route No. (00-63)
Note
(2) 1 : Release Signal arriveNote
Note:
For Resident System Programming,
refer to the Command Manual.•CM36
(1) Incoming Trunk Route No. + Outgoing 
Trunk Route No. (Assigned by CM35 
YY=05)
(2) 0: Allowed
Specify the setting method for Call 
Forwarding-All Calls-Outside.(1) 0: The feature is set when the station
goes on hook/when receiving 
Service Set Tone (ORT time out)
1 :  The feature is set when receiving 
Service Set Tone (ORT time out)
CM12
CM15
CM20
CM35
CM36
A
CM08 START 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 40
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING - ALL CALLS
(1200 Series Enhancement)
DESCRIPTION DATA
Assign whether or not an extention can set 
Split Call Forwarding-All Calls-Outside by 
entering only a trunk access code.(1) 386
(2) 0: Restrict
1 : Allow
Assign whether or not the system should 
check the trunk restriction class of the 
forwarded station during a Split Call 
Forwarding-All Calls-Outside.(1) 387
(2) 0: Split Call forwarding-All Calls-Out-
side Follows setting station class
1 : No check
Assign Call Forwarding-All Calls keys to the 
Multiline Terminals, as required.• YY=00
(1) Primary Extension No. +   + Key No.
(2) F0010: Call Forwarding-All Calls Set/
Cancel
Assign Split Call Forwarding-All Calls keys 
to the Multiline Terminals, as required.(1) Primary Extension No. +   + Key No.
(2) F0A80: Split Call Forwarding-All Call
3.Set/Cancel
Select the feature available in each tenant 
when an internal call and a Tie Line/C.O.
incoming call is terminated.• YY=23 (Internal Call or ATT assisted Call)
• YY=24 (C.O. Incoming Call)
• YY=25 (Tie Line Incoming Call)
(1) Tenant No. (00-63)
(2) 0:  Split Call Forwarding 
1 : Call Forwarding
Assign the destination of Split Call 
Forwarding. 
Note
(1) XX X
Tenant No. (00-63)
Block No. (0-7)
X-XXX
 +   + XX···X
(2) Trunk Access Code
(1-3 digits)
Called No. (Max. 26
digits)
X-XXXX: Station No. (1-4 digits)
Select the Dial Tone on Setting Split Call 
Forwarding-All Calls. 
(1300 Series Enhancement)•Y=2
(1) 13 (Dial Tone on Setting Split Call For-
warding-All Calls)
(2) 0: Special Dial Tone (Stutter Dial Tone)
1 : Dial Tone
CM08
CM90
CM65
CM78
A
CM48
END
,
,
,
INITIAL 
						

							ND-45670 (E) CHAPTER 2
Page 141
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING-ALL CALLS
(1200 Series Enhancement)
Note:The operating procedure for Split Call Forwarding-All Calls is as follows:
CM78 is used to assign the destination forwarded when the destination No. 0-7 is specified.
Dial Destination No. X (0-9)
Dial Access Code for Split Call
Forwarding - All Calls.0: BLOCK No. 0
1: 1
2: 2
3: 3 Destination assigned by
4: 4 CM78.
5: 5
6: 6
7:BLOCK No. 7
8:Destination for Call Forwarding-All Calls
9:Destination for Station Speed Dialing BLOCK
No. 0) Depress Split Call Forwarding - All
Calls key.+ 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 42
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING-BUSY LINE
(1200 Series Enhancement)
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for this feature to 
the required stations.
Note:To provide this feature, set “1”
(Allowed) for YY=11, YY=28, YY
=12, YY=29 of CM15.• CM12 YY = 02
[Service Restriction Class (A) 
(0015 )]
• CM15 YY = 11 (Call Forwarding-Busy 
Line)
• CM15 YY = 28 (Call Forwarding-Busy 
Line-Outside)
• CM15 YY=12 (Call Forwarding-Busy 
Line/-No Answer)
• •CM15 YY=29 (Call Forwarding-Busy 
Line-Outside/-No Answer-Outside)
(1) XX: Service Restriction Class (A) as-
signed by CM12 YY = 02.
(2) 1 : Allowed
Assign the access code for Call Forwarding-
Busy Line, Entry and Cancel, respectively.• Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code (*6, #6)
(2) 014: Entry
015: Cancel
For setting the same access code as Call For-
warding-No Answer
(1) 012: Entry
013: Cancel
Assign the access code for Split Call 
Forwarding-Busy Line.(1) X-XXX: Access Code
(2) A82: Entry
A83: Cancel
START
CM20
A
CM12
CM15 
						

							ND-45670 (E) CHAPTER 2
Page 143
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING-BUSY LINE
(1200 Series Enhancement)
DESCRIPTION DATA
To apply this feature to incoming calls, set the
trunk route combinations for Tandem Connec-
tion.• CM35 YY=05
(1) Trunk Route No. (00-63)
Note
(2) 1 : Release Signal arriveNote
Note:
For Resident System Programming,
refer to the Command Manual.• CM36
(1) Incoming Trunk Route No. + Outgoing 
Trunk Route No. (Assigned by CM35 
YY=05)
(2) 0: Allowed
Specify the setting method for Call Forward-
ing Busy Line-Outside.(1) 222
(2) 0: This feature is set when the station 
goes on hook/when receiving Service Set 
Tone (ORT time out)
1 : This feature is set when receiving
Service Set Tone (ORT time out)
Allow or restrict the ability to set Split Call
Forwarding-Busy Line for a station with Do
Not Disturb set.(1) 240
(2) 0: Allow
1 : Restrict
Assign whether or not an extention can set
Split Call Forwarding-Busy Line-Outside by
entering only a trunk access code.(1) 386
(2) 0: Restrict
1 : Allow
Assign whether or not the system should
check the trunk restriction class of the for-
warded station during a Call Forwarding-
Busy Line-Outside.(1) 387
(2) 0:  Split Call forwarding Busy Line
Outside follows setting station class
1 : No check
CM35
A
B CM36
CM08