NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 2 4
Revision 2.0
ALPHANUMERIC DISPLAY
PROGRAMMING
DESCRIPTION DATA
Provide the system with the Name Display 
Service. (1) 255 
(2) 1 :  To be provided
Station number and number display provided 
when an incoming call terminates to a Prime 
Line and a Primary Extension.(1) 335 
(2) 1 :  To be provided 
Assign the access code for station user name 
entry (used from individual stations).• Y= 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX:  Access Code (62)
(2) A10 
Assign a Trunk Name Number to each Trunk 
Route.• YY = 03
(1) 00-63 : Trunk Route No.
(2) 00 : Trunk Name No. 00
14 : Trunk Name No. 14
15 : Kind of Trunk Route assigned 
by CM35 YY = 00 is displayed 
16 : Trunk Name No.16
63 : Trunk Name No. 63
Assign the desired station user’s name to each 
station number by Y = 0 or Y = 1.• Y = 0 (By Character Code)
(1) X-XXXX:  Station No. 
(2) Character Code
(20-7F:See Character Code Table Max. 
16 digits)
• Y = 1 (By Character) 
(1) X-XXXX:  Station No. 
(2) Character (A-Z, 0-9) Max. 8 charactersCM08
CM20 START
A
CM35
CM77 
						

							ND-45670 (E) CHAPTER 2
Page 25
Revision 2.0
ALPHANUMERIC DISPLAY
Note 1:The maximum number of stations that can be provided with the user’s name display is 384. The maximum
number of characters per name is eight, including spaces. The Maintenance Administration Terminal
(MAT) or Customer Administration Terminal (CAT) can be used to register or change a name. A Multiline
Terminal can register or change the name assignment of that individual Multiline Terminal.
Note 2:User names can be assigned to stations that do not have an LCD. 
Note 3:The trunk name display is provided on a trunk-route basis. The maximum amount of characters in the trunk
name display is four. The maximum number of trunk routes assignable is 16. The MAT or CAT can be used
to register or change a trunk name display.
Note 4:There are two ways to change a name that is currently programmed. (1) by overwriting with a new name,
or (2) by inserting a blank space as the first character to cancel the existing name. 
DESCRIPTION DATA
Assign the desired trunk name to each trunk 
route by Y = 2 or Y = 3.• Y = 2 (By Character Code)
(1) 00-14, 16-63:Trunk Name No. assigned 
by CM35 YY = 03. 
(2) Character Code 
20-7F: See Character Code Table  Max. 8 
digits 
• Y = 3 (By Character) 
(1) 00-14,  16-63: Trunk Name No. assigned 
by CM35 YY = 03. 
(2) Character Code (A-Z, 0-9) Max. 4 char-
acters 
END
CM77
A 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 6
Revision 2.0
ALPHANUMERIC DISPLAY
Character Code Table
234567
0
0@P \ p
1!1AQaq
2”2BRb r
3#3CSc s
4$4DTd t
5%5 EU e u
6&6 FV f v
7’7GWgw
8(8HXhx
9)9IYiy
A*: JZjz
B+;K[k{
C,N^n®
F/?O_o¬
1ST
2ND 
						

							ND-45670 (E) CHAPTER 2
Page 27
Revision 2.0
ANALOG PORT ADAPTER (1200 Series Enhancement)
PROGRAMMING
To assign the Single Port Mode:
To assign the Dual Port Mode:
1. Data Assignment for Multiline Terminal accommodates the Analog Port Adapter.
DESCRIPTION DATA
Provide the Analog Port Adapter to the 
required stations.• YY=32
(1) X-XXXX: Primary Extension No.
(2) 0: To be provided
Assign the Single Port Mode to the required 
stations.• YY=33
(1) X-XXXX: Primary Extension No.
(2) 1 : Single Port Mode
Specify whether a ringing signal is sent to the 
Analog terminal.• YY=35
(1) X-XXXX: Primary Extension No.
(2) 0/1 : Not to be sent/To be sent
DESCRIPTION DATA
Provide the Analog Port Adapter to the 
required stations.• YY=32
(1) X-XXXX: Primary Extension No.
(2) 0: To be provided
Assign the Dual Port Mode to the required 
stations.• YY=33
(1) X-XXXX: Primary Extension No.
(2) 0: Dual Port Mode
START
CM13
END
START
CM13
END
INITIAL 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 8
Revision 2.0
ANALOG PORT ADAPTER (1200 Series Enhancement)
2. Data Assignment for Analog Terminal connected to the Analog Port Adapter.
.
DESCRIPTION DATA
Assign an Analog Terminal Station No. to the 
required LEN.(1) LEN (0000-0511)
(2) FX-FXXXX: Analog Terminal Station 
No.
Note:The Analog Terminal Station No.
must be assigned to the LEN of right
side LT slot to the LT slot for DLC.
Example: When the DLC card is
mounted in the LT01 slot and LT03
slot.
Assignment Example:
CM 10 - LEN 0000 = F 200 for D
term Primary
Extension
LEN 0004 = F 300 for Analog 
Terminal
If level 0 of the LEN is used for the D
term, 
the adjacent level 0 must be used.
START
A
CM10
LT00 LT01LT02
LT03LT04
D
L
CD
L
C
LT slot for assigning
an Analog Terminal
Station No.
(The DLC card is not
mounted in this slot.) 
						

							ND-45670 (E) CHAPTER 2
Page 29
Revision 2.0
ANALOG PORT ADAPTER (1200 Series Enhancement)
DESCRIPTION DATA
Assign a key for Analog Terminal. • YY=00
(1) Analog Terminal Station No. + + Key 
No.
(2) X-XXXX: Analog Terminal Station No. 
assigned by CM10.
Assign an Analog Terminal Station No. as 
Prime Line.(1) X-XXXX: Analog Terminal Station No.
(2) X-XXXX: Analog Terminal Station No.
Provide the Analog Port Adapter to the 
required station.• YY=34
(1) X-XXXX: Analog Terminal Station No.
(2) 0: To be provided
Specify whether a ringing signal is sent to the 
Analog Terminal.• YY=35
(1) X-XXXX: Primary Extension No.
(2) 0/1 : Not to be sent/To be sent
Specify the PAD control of the Analog 
Terminal.• YY=09
(1) X-XXXX: Analog Terminal Station No.
(2) 0/1 : Not Available/AvailableCM90
CM93
CM13
END
A
, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 0
Revision 2.0
ANNOUNCEMENT SERVICE
PROGRAMMING
DESCRIPTION DATA
Specify the Multi-Connection of the Digital 
Announcement Trunk (PN-2DATA) on 
Announcement Service. (1) 124 
(2) 0/1 : Available/Not Available (Single 
Connection)
Assign a Digital Announcement Trunk Circuit 
No. to the required LEN.
Note:The Digital Announcement Trunk
Circuit No. must be assigned to the
first LEN (Level 0) and/or the third
LEN (Level 2) of each LT slot.(1) LEN (0000-0511) 
(2) EB000-EB127: Digital Announcement 
Trunk Circuit No. 
For PIM0/1: EB000-EB031 
For PIM2/3: EB032-EB063 
For PIM4/5: EB064-EB095 
For PIM6/7: EB096-EB127 
• CM12 YY = 02
(1) X-XXXX:  Primary Extension No.
(2) XX
 XX 
*a: Service Restriction Class (A):  
00-15
• CM15 YY = 34 (Group 0) 
• CM15 YY = 35 (Group 1) 
• CM15 YY = 36 (Group 2) 
• CM15 YY = 37 (Group 3) 
• CM15 YY = 38 (Group 4) 
• CM15 YY = 39 [Recording for An-
nouncement Service (Group 0-4)] 
(1) 00-15 : Service Restriction Class (A) 
assigned by CM12 YY = 02 
(2) 1 : Allowed 
Assign access codes for Announcement 
Service. • Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX:  Access Code 
(2) A03:  Recording message (Group 0-4) 
A04:  Replaying message (Group 0)
A05:  Replaying message (Group 1)
A06:  Replaying message (Group 2) 
A07:  Replaying message (Group 3)
A08:  Replaying message (Group 4)
A09:  Deleting message (Group 0-4) 
CM08
CM10 START
A
CM20
CM12
CM15*a 
						

							ND-45670 (E) CHAPTER 2
Page 31
Revision 2.0
ANNOUNCEMENT SERVICE
Note 1:A maximum of five different announcements can be accessed. There is a limit of 10 Digital Announcement
Trunk Circuit for each of the five different announcements. When recording an announcement, each Digital
Announcement Trunk Circuit must be recorded individually.
Note 2:Each time a station is connected to a Digital Announcement Trunk Circuit, the message will be repeated
three times. The station will then be disconnected.
Note 3:For the single connection of a Digital Announcement Trunk Circuit, the duration of an announcement is
limited to 60 seconds. 
Note 4:For the multi-connection of a Digital Announcement Trunk Circuit, the duration of replay for an announce-
ment is programmable from 4 to 396 seconds.
DESCRIPTION DATA
When multi-connection is provided 
(CM08124 = 0), specify the duration of 
message replay for Announcement Service.•Y = 0 
(1) 53
(2) 01-99: 4-396 sec. in 4 sec. increments 
If no data is set, the default setting is 60-64 
seconds.
Assign the function for each Digital 
Announcement Trunk.• YY = 00
(1) 000-127: Digital Announcement Trunk 
Circuit No. assigned by CM10 
(EB000-EB127)
(2) 04X
 X
*a: Group No. (0-4)
*b: Message No. (0-9)
To provide a Tie Line party with this service, 
assign the Announcement Service Group 0-4 
to the required Trunk Routes.• YY = 69 (Group 0)
• YY = 70 (Group 1)
• YY = 71 (Group 2)
• YY = 72 (Group 3)
• YY = 73 (Group 4)
(1) 00-63 : Trunk Route No.
(2) 1 : Allowed
END
CM41
A
CM49
CM35*b *a 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 2
Revision 2.0
ANNOUNCEMENT SERVICE
To provide a voice message when an incoming C.O. line/Tie line call has been transferred and encounters a busy or
no answer condition:
DESCRIPTION DATA
Assign a Digital Announcement Trunk Circuit 
No. to the required LEN.
Note:The Digital Announcement Trunk
Circuit No. must be assigned to the
first LEN (Level 0) and/or the third
LEN (Level 2) of each LT slot.(1) LEN (0000-0511) 
(2) EB000-EB127: Digital Announcement 
Trunk Circuit No. 
For PIM0/1:  EB000-EB031 
For PIM2/3:  EB032-EB063 
For PIM4/5:  EB064-EB095 
For PIM6/7:  EB096-EB127 
Assign the feature for a voice message 
connection to a transferred trunk when the 
transferred destination does not answer or the 
transferred destination is busy to the required 
tenant. • YY = 50 (No Answer)
(1) 00-63:  Tenant No. 
(2) 0 
• YY = 51 (Busy) 
(1) 00-63:  Tenant No. 
(2) 0 
Assign the function for each Digital 
Announcement Trunk.• YY = 00
(1) 000-127: Digital Announcement Trunk 
Circuit No. assigned by CM10 
(EB000-EB127)
(2) 06XX
:  No Answer 
*a: Message No. (00-63)
07XX
:  Busy
*a: Message No. (00-63)
• YY = 06 (No Answer)
• YY = 07 (Busy) 
(1) 00-63: Tenant No. of transferring station 
(2) 00-63: Message No. assigned by YY = 
00
To record, replay, or delete a message, assign 
the respective Digital Announcement Trunk 
access code. • Y = 0-3 (Number Plan Group 0-3) 
(1) X-XXX:  Access Code 
(2) A00:  Record 
A01:  Replay 
A02:  Delete 
CM10 START
END
CM65
CM49
CM20
*a
*a 
						

							ND-45670 (E) CHAPTER 2
Page 33
Revision 2.0
ANNOUNCEMENT SERVICE
Note 5:Announcement Service can be used to provide a voice message when an incoming C.O. line/Tie line call
has been transferred and encounters a busy or no answer condition. After the voice message is given, nor-
mal call processing continues. 
-This application can be programmed on a tenant basis.
- Only one (1) message of up to 60 seconds can be recorded on an individual Digital Announcement Trunk
Circuit. 
- In this application, a minimum of two digital announcement Trunk Circuits are needed, one for busy
condition, and one for no answer.
- More than one Digital Announcement Trunk Circuit can be used, depending on traffic conditions.
- System programming can be set to, wait until circuit(s) become free or immediately follow prepro-
grammed normal call handling, if a busy condition is encountered.
- Digital Announcement Trunk Circuits can be shared among tenants.
- This feature does not function on Attendant transferred calls.