NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 3 20
Revision 2.0
NIGHT SERVICE: TRUNK ANSWER ANY STATION (TAS)
PROGRAMMING 
DESCRIPTION DATA
Assign a Trunk Restriction Class to each 
station. •  YY = 01
 (1)  X-XXXX (Station No.) 
 (2)  XX
*a: Trunk Restriction Class in Night 
Mode (1-7) 
1 : Unrestricted (RCA) 
2: Non-Restricted 1 (RCB) 
3: Non-Restricted 2 (RCC) 
4: Semi-Restricted 1 (RCD) 
5: Semi-Restricted 2 (RCE) 
6: Restricted 1 (RCF) 
7: Restricted 2 (RCG) 
Assign the Class of Service for TAS to the 
required stations. •  CM12 YY = 02 
Service Restriction Class B (00-15 ) 
•  CMI5 YY = 53 
 (1)  Service Restriction Class B (00-15) as-
signed by CM12 YY = 02
 (2)  1 : Allowed 
Assign TAS as the terminating system in 
Night Mode for the required trunks. •  YY = 03
 (1)  000-255 (Trunk No.) 
 (2)  13: TAS 
Assign the TAS Group No. to the trunks 
assigned by YY = 03. •  YY = 17
 (1)  000-255 (Trunk No.) 
 (2)  00-63 (TAS Group No.) 
CM12 START
A
CM30
CM12
CM15
*a 
						

							ND-45670 (E) CHAPTER 2
Page 321
Revision 2.0
NIGHT SERVICE: TRUNK ANSWER ANY STATION (TAS)
DESCRIPTION DATA
Specify the function of each type of TAS 
within a system.•  Y = 0-4 (TAS Answer A-E) 
 (1)  Type of Call
1: C.O. Incoming Call 
2: Tie Line/DID 
3: C.O. Incoming Call in Night Mode 
4: Overflowed DIT Call
 (2)  0/1 : Cannot be answered/Can be an-
swered 
 (1)  7: A call terminated to a different ten-
ant.
 (2)  0/1 : Can be answered 
Assign the access code for each type of TAS 
(TAS Answer A-E) assigned by CM53. •  Y = 0-3 (Numbering Plan Group 0-3) 
 (1)  X-XXX: Access Code (72) 
 (2)  047: TAS Answer A 
048: TAS Answer B 
049: TAS Answer C 
050: TAS Answer D 
051: TAS Answer E 
Specify the Tenants allowing TAS Answer 
between them. • Y = 0
 (1)  XX
 XX
*a: 00-63 (Tenant No. of TAS Answer 
station) 
*b: 00-63 (Tenant No. of Trunk) 
 (2)  0/1 : Allowed/Restricted 
END
CM53
A
CM20
CM63
0
1
2
3
4
01347 (1)
Y
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/10/1
0/1
0/1
0/1
0/10/1
0/1
0/1
0/1
0/10/1
0/1
0/1
0/1
0/1TAS
Answer A
TAS
Answer B
TAS
Answer C
TAS
Answer D
TAS
Answer E
*b *a 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 22
Revision 2.0
NIGHT SERVICE: TRUNK ANSWER ANY STATION (TAS)
To provide the External TAS Indicator using the PN-DK00 card:
To provide the Telephone set for TAS Indication using the PN-4LC card:DESCRIPTION
DATA
Assign the PN-DK00 card No. to the required 
LEN. (1)  LEN (0000-0511) 
 (2)  E800-831 (PN-DK00 Card No.) 
For PIM0/1: E800-E807 
For PIM2/3: E808-E815 
For PIM4/5: E816-E823 
For PIM6/7: E824-E831 
Assign the TAS Group No. assigned by 
CM30 YY = 17 to the circuit No. of the PN-
DK00 card.  (1)  XX
 X (Circuit No.) 
*a: Card No. (00-31) assigned by CM10 
(E800-E831) 
*b: Circuit No. (0-3) 
 (2)  13XX
*a: 00-63 (TAS Group No.00-63 as-
signed by CM30 YY = 17) 
Specify the indication pattern on the External 
TAS Indicator.  (1)  00
 (2)  01 : 30 IPM (1 sec. ON/OFF) 
02: 60 IPM (0.5 sec. ON/OFF) 
03: 120 IPM (0.25 sec. ON/OFF) 
07: Steadily on.
DESCRIPTION DATA
Assign the TAS Buzzer No. (Telephone set for 
TAS Indication) to the required LEN.
The TAS Buzzer No. must correspond to the 
TAS Group No. assigned by CM30 YY = 17.
E600®TAS Group 00
E663®TAS  Group 63 (1)  LEN (0000-0511) 
 (2)  E600-E663 (TAS Buzzer No.)
CM10 START
CM59
END
CM44*b *a
*a
CM10 START
END 
						

							ND-45670 (E) CHAPTER 2
Page 323
Revision 2.0
NIGHT SERVICE: TRUNK ANSWER ANY STATION (TAS)
HARDWARE REQUIRED 
To provide the External TAS Indicator: 
• PN-DK00
• Indicator 
Requirement for External Indicator
Control Method: Ground/Battery (-24 V) (Max.125 mA) 
Type:  Visual and/or Audible type with volume control
Make the following connections at the MDF according to the type of the indicator. For details, refer to the MDF
cross connection for a TAS Indicator in the INSTALLATION PROCEDURE MANUAL.
To provide the Telephone set for TAS Indication: 
• PN-4LC card (Four telephone sets per card can be equipped.) 
• Conventional telephone sets 
PBX
PN-DK00 CARD
PZ-PW86 CARD
G
PBX
PN-DK00 CARDMDF
MDFEXTERNAL INDICATOR
WITH BATTERY
EXTERNAL INDICATOR WITH
BATTERY (GROUND START)IND
IND
G 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 24
Revision 2.0
OFF-HOOK ALARM
PROGRAMMING
DESCRIPTION DATA
Provide this feature for the required stations.  •  YY = 02
(1) X-XXX (Station No.) 
(2)  0: To be provided 
Assign the destination for Off-Hook Alarm 
to a Station or SN610 ATTCON. •  YY = 12 
(1)  Tenant No. (00-63) 
(2) X-XXXX (Station No.) 
E000: SN610 ATTCON
If the Attendant Console is designated as the 
destination of Off-Hook Alarm by CM51 YY 
= 12, assign an EMG key for the Off-Hook 
Alarm to any Key. •  YY = 00
(1)  ATTCON No. +   + Key No.
(2)  F6056: Emergency Call 
Specify the timing for Off-Hook Alarm. •  Y = 0 
(1) 22
(2)  01-08: 4-32 sec. in 4 sec. increments
If no data is set, default setting is 28-32 sec-
onds.
Specify the service to be applied for an Off-
Hook Alarm Call to a busy destination.•  CM12 YY = 07 
(1)  X-XXXX (Station No. of destination) 
(2)  Service Rest. Class C (00-15 )
•  CM15 YY = 97, YY = 98 
(1)  Service Rest. Class C (00-15) assigned 
by CM12 YY = 07.
(2) See left column.CM13 START
CM41
CM12
CM15
END
CM90
CM51
,
YY
MEANING OF DATA
97 98
00Call Waiting (When UCD Pilot 
Station and CM08-212 = 0)
01UCD (When UCD Pilot 
Station and CM08-212 = 1)
10Call Waiting (For Ordinary 
Station)
1 1 Hunting (For Ordinary Station) 
						

							ND-45670 (E) CHAPTER 2
Page 325
Revision 2.0
OFF PREMISES EXTENSION
PROGRAMMING 
HARDWARE REQUIRED 
PN-AUCA card
DESCRIPTION DATA
Remove the PAD on Off Premises Extension.  •  YY  =  09
 (1)  X-XXXX (Station Number) 
 (2)  0: No PAD (6 dB) CM13 START
END 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 26
Revision 2.0
PAD LOCK (1300 Series Enhancement)
PROGRAMMING
1. In case of a system with AP card (PN-AP01):
DESCRIPTION DATA
Assign the slot number to AP card
Note:Set SENSE switch on the card to the
slot number assigned(1) Slot No. (04-15)
(2) 07: PN-AP01 card
Designate the AP card for Authorization 
Code.(1) 216:Designation of Processor for Autho-
rization Code
(2) 1 : AP (PN-AP01)
Specify the Service Set Tone after dialling the 
access code for Authorization Code.(1) 362:Provision of Service Set Tone after 
dialling the access code
(2) 1 : To be provided
Set the data for 281 to 1. (Maid ID Code is not 
used.)(1) 281
(2) 1 : Not available
Assign the Service Restriction Class (A) 
allowed for Authorization Code feature.• YY=31 (Authorization Code)
(1) Service Restriction Class (A) (00-15)
(2) 1 : Allowed
Assign allowed class and restricted class for 
Maid Status feature.• YY=75 (Maid Status)
(1) Service Restriction Class (B) (00-15)
(2) 0: Restricted
1 : Allowed
To the station that uses PAD LOCK feature, 
assign the Service Restriction Class (A) 
allowed for Authorization Code feature. 
Moreover, to all the station, assign the Service 
Restriction Class (B) restricted for Maid 
Status feature.• YY=02
(1) X-XXXX: Station No.
(2) XX
 XX
Service Restriction Class (A)
Service Restriction Class (B)
Assign the access code for Authorization 
Code.• Y=0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code
(2) 086: Authorization Code
CM05
CM08
CM15
CM12
CM20
A START
INITIAL 
						

							ND-45670 (E) CHAPTER 2
Page 327
Revision 2.0
PAD LOCK (1300 Series Enhancement)
DESCRIPTION DATA
Specify the maximum number of digits for 
Authorization Code.(1) 11:Authorization Code Max. digits
(2) Max. number of digits
01: 1 digit
08: 8 digits
NONE : 8 digits
Specify the conditions for adding Check Code 
to each Authorization Code.
Check Code consists of 2 digits: 1st and 2nd 
Check Code which are generated by the AP 
according to the conditions specified by Y=0 
and Y=1.
Authorization Code:
X
1 X2 X3 X4 X5 X6 X7 X8 C1 C2
X: Significant Digit for Check Code• Y=0 (Designation of Significant 
digit for Check Code)
(1) 0: For 1st Check Code
1: For 2nd Check Code
(2) 00 X
 X: Significant digit designation
5th-8th digit (0-F)
1st-4th digit (0-F)
(See left column)
If no Check Code is required, set 
data=0000 to both 1st and 2nd 
Check Code.
• Y=1 (Setting of Check Sum Data for 
generating Check Code)
(1) 0:For 1st Check Code
(2) 1: For 2nd Check Code
0-9: Check Sum Data (Enter 
desired value)
CM42
CMD5
A
B
~
~
ID Code programmedCheck Code
X1X2X3X4
X5X6X7X8
0 No Check Code
1X
2X
3XX
4X
5XX
6XX
7 XXX
8X
9X X
AXX
BXXX
CXX
DXXX
EXXX
F XXXX
DIGIT
DATA 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 28
Revision 2.0
PAD LOCK (1300 Series Enhancement)
DESCRIPTION DATA
Set the Authorization Code and the Temporary
Service Class given by CM15. 
Service Restriction Class (B) of the Temporary
Service Class should be set to the allowed class
for Maid Status.
• Temporary Service Class.
2 X
2 X3 X4 X5 X6 X7 X8 X9
•
(1)
(2)Y=3
X-X...X: Authorization Code
2 X
2 ...X9 (9 digits)
(See column below)
2: Type of Temporary Service Class as per 
X
2...X9 
Trunk Restriction Class (01-08)
Service Restriction Class (A) (01-15)
Service Restriction Class (B) (01-15)
(Allowed class for Maid Status)
Service Restriction Class (C) (01-15)
Assign the access code for Maid Status. •
(1)
(2)YY=0-3 (Numbering Plan Group 0-3)
X-XXX (Access Code)
029
Assign the Class of Service for Maid Status. (1)
(2)X-XXXX: Station No.
Service Class No. (0-15)
Assign the Maid Status Processing to the 
Service Class assigned by CMD015.(1)
(2)XX
 06
Service Class No. assigned by
CMD015
1: Yes
CMD5
CM20
C
CMD015
CMD016
B 
						

							ND-45670 (E) CHAPTER 2
Page 329
Revision 2.0
PAD LOCK (1300 Series Enhancement)
DESCRIPTION DATA
Allow each Status Number (Restricted/
Normal) to change the Status Number from 
the station.
Note:Desired number can be assigned for
the Status Number of each status.(1) 1
 31
Status No. (Restricted) Note
Allowed to change the Status
No. from the station
(2) 1: Yes
(1) 2
 31
Status No. (Normal) Note
Allowed to change the Status
No. from the station.
(2) 1: Yes
Assign the originating function, the incoming 
call function, and the other function to each 
Status Number as following table.(1) 1
 00
Status No. (Restricted)
No originating allowed (Room
Cut Off)
(2) 1: Yes
(1) 1
 01
Status No. (Restricted)
Originating allowed (Room Cut
Off Reset)
(2) 0 : No
(1) 2
 00
Status No. (Normal)
No originating allowed (Room
Cut Off)
(2) 0 : No
(1) 2
 01
Status No. (Normal)
Originating allowed (Room Cut
Off Reset)
(2) 1: Yes
CMD031
D
C
ROOM 
STATUS No.FUNCTION
00 01 02 03 04 05 06 07
1 
(Restricted)100/10/10000
2 
(Normal)010/10/10000