NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 2 04
Revision 2.0
DIRECT INWARD SYSTEM ACCESS (DISA)
Note 1:Up to 1,000 Direct Inward System Access (DISA) codes combined with Authorization Codes and Forced
Account Codes can be defined. 
Note 2:When deleting all ID codes stored in the PN-AP01 card at one time, do the following operation:
 + D60 +   + 0000 +   + CCC +  
HARDWARE REQUIRED 
PN-AP01 card ´ 1 (If 1,000 codes and/or Check Code is provided.)
PN-2DATA card x n (n = 1-128) (If a Digital Announcement Trunk is required for the DISA.) ST
DEDEEXE 
						

							ND-45670 (E) CHAPTER 2
Page 205
Revision 2.0
DIRECT INWARD TERMINATION (DIT)
PROGRAMMING 
DESCRIPTION DATA
Assign the data for terminating system in Day 
Mode and Night Mode, to each Loop/Ground 
Start trunk, respectively. • YY = 02 (Day Mode)/YY = 03 (Night 
Mode)
(1) Trunk No. (000-255)
(2) 04: Direct-In Termination
Assign the station number to be terminated by 
DIT in Day Mode and Night Mode 
respectively.• YY = 04 (Day Mode)/YY = 05 (Night 
Mode)
(1) Trunk No. (000-255)
(2) X-XXXX: Station No.
Assign the destination to be rerouted when the 
DIT Station is busy/not available in Day Mode 
and Night Mode respectively.• YY = 13 (Day Mode)/YY = 14 (Night 
Mode)
(1) Trunk No. (000-255)
(2) 01: TAS BUZZER 
04: SN610 ATTCON
06: Automatic Camp-On 
15: Waiting until the DIT Station 
becomes idle.
Assign the transfer destination for an 
unanswered DIT call in the Day Mode and 
Night Mode, respectively.• YY = 15 (Day)/YY = 16 (Night)
(1) Trunk No. (000-255)
(2) 01: SN610 ATTCON
03: TAS
15: To be continued DIT
Specify the timing for an unanswered call to a 
DIT destination.•Y = 0
(1) 01
(2) 01-30: 4-120 sec. in 4 sec. increments
If no data is set, the default setting is 32-
36 seconds.
Set the ring rate on a DIT call. (1) 179 
(2) 0/1: As per the data assigned by 
CM35 YY = 33/0.4 sec. ON, 0.2 
sec. OFF, 0.4 sec. ON, 2 sec. OFF.CM30
END
START
CM41
CM08 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 06
Revision 2.0
DIRECT OUTWARD DIALING (DOD)
PROGRAMMING
DESCRIPTION DATA
Assign the Trunk Numbers to the required 
LENs.(1) LEN (0000-0511) 
(2) Trunk No. (D000-D255)
Assign the data for Direct Outward Dialing to 
the Trunk No. assigned by CM10. 
Note:For Resident System Program, refer
to the Command Manual. • YY = 00 (Trunk Route Allocation) 
(1) Trunk No. (000-255)
(2) Route No. (00-63) Note
 
• YY = 01 (Tenant Allocation)
(1) Trunk No. (000-255)
(2) Tenant No. (00-63) (01)
• YY = 08 (Restriction on Night Mode)
(1) Trunk No. (000-255)
(2) 0/1 : Restricted/Allowed
CM10
CM30 START
A 
						

							ND-45670 (E) CHAPTER 2
Page 207
Revision 2.0
DIRECT OUTWARD DIALING (DOD)
DESCRIPTION DATA
Assign the data for Direct Outward Dialing to 
the Route No. assigned by CM30 YY = 00. 
Note:For Resident System Program, refer
to the Command Manual. • YY = 00 (Kind of Route)
(1) Trunk Route No. (00-63)
(2) 00: DDD 
01: FX
02: WATS
03: CCSA
• YY = 01 (Type of Signal) 
(1) Trunk Route No. (00-63) 
(2) 2: DP
4: DTMF 
• YY = 02 (OG/IC) 
(1) Trunk Route No. (00-63)
(2) 2 : Outgoing 
3:Bothway 
• YY = 04 (Answer Signal Condition)
(1) Trunk Route No. (00-63)
(2) 1 : Answer Signal by Polarity Re-
versal 
7:No Answer Signal 
In case of no Answer Signal, system recog-
nizes the answer in timing set by CM41-03. 
• YY = 05 (Release Signal Condition) 
(1) Trunk Route No. (00-63)
(2) 0 : No Release Signal from C.O.
1:Release Signal from C.O. 
• YY = 08 (Dial Pulse Sending) 
(1) Trunk Route No. (00-63) 
(2) 3: To be sent
• YY = 09 (Incoming Connection Signal-
ling) 
(1) Trunk Route No. (00-63) 
(2) 01 : Ring Down (Ground Start) 
15:Ring Down (Loop Start)
CM35
B
A 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 08
Revision 2.0
DIRECT OUTWARD DIALING (DOD)
Note:For the Trunk Restriction Class, refer to Class of Service Individual.
DESCRIPTION DATA
According to the characteristics of each C.O. 
line, assign the data for DP/DTMF Sender to 
each route. 
For the details of the command, refer to the 
Command Manual.
Note:For Resident System Program, refer
to the Command Manual. • YY = 20 (Sender Start Condition) 
• YY = 21 (Sender Prepause Timing) 
• YY = 23 (DP-Inter Digital Pause) 
• YY = 24 (DTMF-Inter Digital Pause) 
• YY = 25 (DP-Make Ratio)
• YY = 26 (DTMF Signal Width)
• YY = 45 (DP Sender Release Timing) 
• YY = 46 (DTMF Sender Release 
Timing) 
Specify the timing for Interdigital Pause on 
outgoing C.O. call.•Y = 0
(1) 27
(2) 01-14: 1-14 sec. in 1 sec. increments
If no data is set, the default setting is 7 
seconds.
Assign the access code to each route.  • Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX: Access Code
(2) 100-163: Route No. (00-63)
Assign the trunk appearance line key on a 
Multiline Terminal, if provided.• YY = 00
(1) Primary Extension No. +    + Key No.
(2) DXXX (Trunk No. 000-255)
CM35
B
END
CM20
CM90
CM41
, 
						

							ND-45670 (E) CHAPTER 2
Page 209
Revision 2.0
DIRECT STATION SELECTION/BUSY LAMP FIELD (DSS/BLF) CONSOLE
PROGRAMMING
HARDWARE REQUIRED 
DSS Console 
PN-2DLCB/4DLCA card (Two or four DSS Consoles can be accommodated per card) 
DESCRIPTION DATA
Assign the DSS Console Number to its 
associated LEN.(1) 0000-0511 (LEN)
(2) DSS Console No. 
E100-E107: For PIM0/1 
E108-E115: For PIM2/3 
E116-E123: For PIM4/5 
E124-E131: For PIM6/7 
Assign a single-line station, Multiline 
Terminal, or SN610 ATTCON to work in 
conjunction with the DSS Console.(1) 00-31 (DSS Console Number: Last two 
digits of E100-E131 assigned by 
CM10) 
(2) X-XXXX (Station Number/Primary 
Extension No. of Multiline Terminal)
E000-E007 (SN610 ATTCON No.) 
Assign the station and trunk numbers, as 
needed, to the keys on each DSS Console. (1) 00-31 (DSS Console Number) +   
+ DSS Key Number (00-59)
(2) X-XXXX (Station Number)
D XXX
*a: 000-255 (Trunk Number)
Assign a Do Not Disturb and Message 
waiting function key, if needed, on each DSS 
Console. (1) 00-31 (DSS Console Number) +   + 
Function key No. (57-59)
(2) F1049: Message Waiting Set/Reset
F1053: Do Not Disturb Set/Reset 
When providing Do Not Disturb or Message 
Waiting function key, assign a changing 
Function key on each DSS Console.(1) 00-31 (DSS Console Number) +    + 
Function key No. (56) 
(2) F1052: Changing Function 
Specify the type of busy indication on the 
BLF of the DSS Console as Station Base or 
Extension Base.(1) 269
(2) 0/1: Station Base/Extension Base 
CM10
END
START
CM97
CM08
CM96
,
*a
,
, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 10
Revision 2.0
DISTINCTIVE RINGING
PROGRAMMING
DESCRIPTION DATA
Select the ringing pattern on an internal and 
Direct-In Termination Call, Direct Inward 
Dialing, DISA, and Automated Attendant. (1) 138 (For Internal)
(2) 0/1: 2 sec. ON, 4 sec. OFF/1 sec. 
ON, 2 sec. OFF. 
(1) 179 (For DIT Call)
(2) 0/1: As per CM35 YY = 33/0.4 sec. 
ON, 0.2 sec. OFF, 0.4 sec. ON, 2 
sec. OFF. 
(1) 180 (For DID, DISA and Automated 
Attendant) 
(2) 0/1:0.2 sec. ON, 0.2 sec. OFF, 0.2 
sec. ON, 0.2 sec. OFF, 0.2 sec. 
ON, 0.2 sec. OFF/As per the 
data CM35 YY = 33 
Select the ringing pattern on an external call. 
Note:For incoming calls to a Direct Trunk
Appearance key on Multiline Termi-
nals, the special ringing, 0.2 sec. ON,
0.2 sec. OFF, 0.2 sec. ON, 0.2 sec.
OFF, will be applied.
• YY = 33
(1) Trunk Route No. (00-63)
(2) 0 : 0.4 sec. ON, 0.2 sec. OFF 
Note 
0.4 sec. ON, 2.0 sec. OFF 
Note
1 : 0.4 sec. ON, 0.2 sec. OFF
0.4 sec. ON, 2.0 sec. OFF 
2 : 1 sec. ON, 2 sec. OFF
3:2 sec. ON, 4 sec. OFF
Select the ringing pattern on station calls 
with a trunk line placed in Consultation Hold.(1) 137 
(2) 0: Change from Internal Ringing 
(CM08-138) to External Ringing 
(CM35 YY = 33) when transfer-
ring a call
1: External Ringing (CM35 YY = 
33)
CM08
END
START
CM35
CM08 
						

							ND-45670 (E) CHAPTER 2
Page 211
Revision 2.0
DISTINCTIVE RINGING
To provide a distinctive lamp indication for Multiline Terminals during a call termination, do the following program-
ming:
DESCRIPTION DATA
Specify the lamp color for an incoming 
external call. 
Note:The lamp color for incoming inter-
nal calls is red (120 IPM flashing).
For indicating the termination of a
transferred external incoming call,
the flashing lamp color depends on
CM08-137. • YY = 32
(1) Trunk route number (00-63) 
(2) 0/1: Green/Red 
END
START
CM35 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 12
Revision 2.0
DO NOT DISTURB
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for Do Not 
Disturb to the required stations.• CM12 YY=02: Service Rest. Class (A)
(00-15t)
• CM15 YY=19
(1) Service Rest. Class (A) (00-15) assigned 
by CM12 YY=02
(2) 1 : Allowed
Assign the group of stations in Do Not 
Disturb. Do Not Disturb is set to these stations 
(assigned by this command) simultaneously 
by operation from an Attendant Console.• YY=00
(1) X-XXXX (Station No.)
(2) 0: To be provided
Assign the access code for Do Not Disturb 
Set/Cancel.• Y=0-3 (Numbering Plan Group 0-3) 
(1) X-XXX: Access Code (*8, #8) 
(2) 022: Set 
023: Cancel
Assign the destination to which a call is 
transferred when the called station is set to Do 
Not Disturb.• YY=10 
(1) 00-63 (Tenant No.) 
(2) X-XXXX (Station No.) 
E000 (SN610 ATTCON)
Assign a DND function key to a Multiline 
Terminal, if needed.• YY=00 
(1) Primary Extension No. +   + Key No. 
(2) F0022: Do Not Disturb Set/Reset
Assign DND and DNDOVR function keys to 
the SN610 ATTCON.
Note:By Resident System Program, a DN-
DOVR key is assigned as a soft key,
on the SN610 ATTCON.• YY=00 
(1) ATTCON No. +   + Key No. 
(2) F6102: DND 
F6103: DND Override
F6104: RESET
CM12
CM15
CM20
CM51
A
CM90 START
CM13
,
, 
						

							ND-45670 (E) CHAPTER 2
Page 213
Revision 2.0
DO NOT DISTURB
DESCRIPTION DATA
Specify the Call Forwarding-Busy Line/
Station Hunting for a station set for Do Not 
Disturb.240 
0: Available 
1 : Not Available
For a system using multiple tenants, specify 
for which tenant (the calling or called station) 
the assignment refers to CM51 YY=10. CM51 
YY=10 determines the destination to which a 
call is transferred when the called station is in 
Do Not Disturb.241 
0:  Tenant of called station 
1 :  Tenant of calling station
Select the Dial Tone on Setting Do Not 
Disturb. (1300 Series Enhancement)Y=2 
14 (Dial Tone on Setting Do Not Disturb) 
0:  Special Dial Tone (Stutter Dial Tone)
1 : Dial ToneCM08
A
CM48
END
INITIAL