NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 1 44
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING-BUSY LINE
(1200 Series Enhancement)
DESCRIPTION DATA
Assign Call Forwarding-Busy Line keys to the 
Multiline Terminals, as required.• YY=00
(1) Primary Extension No. + + Key No.
(2) F0014: Call Forwarding-Busy Line Set/
Cancel
For setting the same key as Call For-
warding -No Answer
(3) F0012: Set/Cancel
Assign Split Call Forwarding-Busy Line keys 
to the Multiline Terminals, as required.(1) Primary Extension No. + + Key No.
(2) F0A82: Split Call Forwarding-Busy
Line/-No Answer Set/Cancel
Select the feature available in each tenant 
when an internal call and a Tie Line/C.O. 
incoming call is terminated.• YY=23 (Internal Call or ATT Assisted 
Call)
• YY=24 (C.O. Incoming Call)
• YY=25 (Tie Line Incoming Call)
(1) Tenant No. (00-63)
(2) 0: Split Call Forwarding 
1 : Call Forwarding
Assign the destination of Split Call 
Forwarding. 
Note
XX X
*a *b
*a: Tenant No. (00-63)
*b: Block No. (0-7)
X-XXX
 +   + XX···X
*a *b
*a: Trunk Access Code (1-3 digits)
*b: Called No. (Max. 26 digits)
X-XXXX: Station No. (1-4 digits)
CM78
B
END
CM65,
,
, 
						

							ND-45670 (E) CHAPTER 2
Page 145
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING-BUSY LINE
(1200 Series Enhancement)
Note:The operating procedure for Split Call Forwarding-Busy Line/No Answer is as follows:
CM78 is used to assign the destination forwarded when the destination No. 0-7 is specified.
Dial Destination No. X (0-9).
0: BLOCK No. 0
1: 1
2: 2
3: 3
4: 4
5: 5
6: 6
7: BLOCK No. 7
8: Destination for Call Forwarding-Busy
Line/-No Answer
9: Destination for Station SpeedDialing
(BLOCK No. 0)
+
Dial Access Code for Split Call
Forwarding-Busy Line/-No An-
swer.
or
Depress Split Call Forwarding -
Busy Line/-No Answer key.
Destination assigned
by CM78. 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 46
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING-NO ANSWER
(1200 Series Enhancement)
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for this feature to 
the required stations.
Note:To provide this feature, set “1” (Al-
lowed) for YY=10, YY=27, YY=12,
YY=29 of CM15.• CM12YY=02 
[Service Restriction Class (A) (00-
15 )]
• CM15YY=10 (Call Forwarding-No 
Answer)
• CM15YY=27 (Call Forwarding-No 
Answer-Outside)
• CM15 YY=12 (Call Forwarding-Busy 
Line/-No Answer)
• CM15 YY=29 (Call Forwarding-Busy 
Line-Outside/-No Answer-Outside)
(1) XX: Service Restriction Class (A) 
assigned by CM12 YY=02.
(2) 1 : Allowed
Assign the access code for Call Forwarding-
No Answer, Entry and Cancel, respectively.• Y=0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code (*6, #6)
(2) 016: Entry 
017: Cancel
For setting the same access code as Call For-
warding-Busy Line
(2) 012: Entry 
013: Cancel
Assign the access code for Split Call 
Forwarding-No Answer.(1) X-XXX: Access Code 
(2) A82: Entry
A83: Cancel
START
CM12
CM15
CM20
A 
						

							ND-45670 (E) CHAPTER 2
Page 147
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING- NO ANSWER
(1200 Series Enhancement)
DESCRIPTION DATA
Specify the timing for Call Forwarding-No 
Answer for a trunk incoming call.•Y=0
(1) 01
(2) 01-30 (Timer Data for 0-120 sec. in 4-
sec. increments)
If no data is set, the default setting is 32-36
seconds.
Specify the timing for Call Forwarding-No 
Answer for an internal call or an assisted call.•Y=0
(1) 15
(2) 01-30: 0-120 sec. in 4 sec. increments
If no data is set, the default setting is 32-36
seconds.
To apply this feature to incoming calls, set the 
trunk route combinations for Tandem 
Connection.• CM35 YY=05
(1) Trunk Route No. (00-63)
Note
(2) 1 : Release Signal arriveNote
Note:
For Resident System Programming,
refer to the Command Manual.• CM36
(1) Incoming Trunk Route No. + Outgoing 
Trunk Route No. (Assigned by CM35 
YY=05)
(2) 0: Allowed
Specify the setting method for Call 
Forwarding-No Answer-Outside.(1) 222
(2) 0:  The feature is set when the station 
goes on hook/when receiving Service Set 
Tone (ORT time out)
1 : The feature is set when receiving 
Service Set Tone (ORT time out)
Assign whether or not an extention can set 
Split Call Forwarding-No Answer-Outside by 
entering only a trunk access code.(1) 386
(2) 0: Restrict
1 : Allow
Assign whether or not the system should 
check the trunk restriction class of the 
forwarded station during a Split Call 
Forwarding-No Answer-Outside.(1) 387
(2) 0: Split Call forwarding No Answer-
Outside follows setting station class
1 : No check
CM41
A
B
CM36
CM35
CM08 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 48
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING- NO ANSWER
(1200 Series Enhancement)
DESCRIPTION DATA
Assign Call Forwarding-No Answer keys to 
the Multiline Terminals, as required.• YY=00
(1) Primary Extension No. + + Key No.
(2) F0016: Call Forwarding-No Answer Set/
Cancel
For setting the same key as Call Forwarding-
Busy Line.
(3) F0012: Set/Cancel
Assign Split Call Forwarding-No Answer 
keys to the Multiline Terminals, as required.(1) Primary Extension No. + + Key No.
(2) F0A82: Split Call Forwarding-Busy 
Line/-No Answer Set/Cancel
Select the feature available in each tenant 
when an internal call and a Tie Line/C.O. 
incoming call is terminated.• YY=23 (Internal Call or ATT assisted 
Call)
• YY=24 (C.O. Incoming Call)
• YY=25 (Tie Line Incoming Call)
(1) Tenant No. (00-63)
(2) 0:  Split Call Forwarding 
1 :  Call Forwarding
Assign the destination of Split Call 
Forwarding. 
Note
(1) XX X
*a *b
*a: Tenant No. (00-63)
*b: Block No. (0-7)
X-XXX
 +   + XX···X
*a *b
*a: Trunk Access Code (1-3 digits)
*b: Called No. (Max. 26 digits)
X-XXXX: Station No. (1-4 digits)
CM78
B
END
CM65
CM90,
,
, 
						

							ND-45670 (E) CHAPTER 2
Page 149
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING- NO ANSWER
(1200 Series Enhancement)
Note:The operating procedure for Split Call Forwarding-Busy Line/No Answer is as follows:
CM78 is used to assign the destination forwarded when the destination No. 0-7 is specified.
Dial Destination No. X (0-9).
0: BLOCK No. 0
1: 1
2: 2
3: 3
4: 4
5: 5
6: 6
7: BLOCK No. 7
8: Destination for Call Forwarding-Busy Line/ No
Answer
9: Destination for Station Speed Dialing (BLOCK
No. 0)
+
Dial Access Code for Split Call
Forwarding-Busy Line/-No An-
swer.
or
Depress Split Call Forwarding -
Busy Line/-No Answer key.
Destination assigned by
CM78. 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 50
Revision 2.0
CALL FORWARDING: SET/RESET FROM MAT/CAT
(1700 Series Enhancement)
To set or reset the Call Forwading service from a MAT/CAT, use the following command.
DESCRIPTION DATA
Use YY = 00-03 for Call Forwarding and YY 
= 04-05 for Split Call Forwarding. To reset 
the service, assign CCC to the second data 
of each YY No.• YY = 00 (CF-All Calls) 
• YY = 01 (CF-Busy Line) 
• YY = 02 (CF-No Answer) 
• YY = 03 (CF-Busy Line/No Answer) 
(1) X-XXXX: Station No.
(2) Destination No.

X-XXXX: Station No.

X-XX
 +,+ YY....YY
*a *b *c
*a: Outgoing Trunk/LCR GroupAc-
cess Code (1-2 digits)
*b: Separate Mark
*c: Called No. (Max.26 digits)

E000: ATTCON
• YY = 04 (Split CF-ALL Calls)
• YY = 05 (Split CF-Busy Line/No An-
swer)
(1) XXXX: Station No.
(2) 0: Target Station for Split CF (Block 0)/
AT T
1: Target Station for Split CF (Block 1)
2: Target Station for Split CF (Block 2)
3: Target Station for Split CF (Block 3)
4: Target Station for Split CF (Block 4)
5: Target Station for Split CF (Block 5)
6: Target Station for Split CF (Block 6)
7: Target Station for Split CF (Block 7)
8: Target Station for Call Forwarding 
9: Station Speed Dialing (Block 0)
CME6 START
END 
						

							ND-45670 (E) CHAPTER 2
Page 151
Revision 2.0
CALL FORWARDING: GROUP DIVERSION
PROGRAMMING
Note:The number of Stations that can be included in the same group is unlimited.
DESCRIPTION DATA
Provide the system with Group Diversion. (1) 026 (Group Diversion)
(2) 0: To be provided
Set up the members to be included in each 
Group Diversion Group.
Note
• Y = 2 (Group Diversion Group)
(1) X-XXXX (Station No. to be included in 
Group Diversion)
(2) 00-30 (Group Diversion Group No. )
Assign the destination for each Group 
Diversion Group to the required stations.•Y = 6
(1) 00-30 (Group Diversion Group No. )
(2) X-XXXX (Destination Station No. )
Set the timing for transferring a call using this 
feature.•Y = 0
(1) 01
(2) 01-30: 4 - 120 sec. in 4 sec. increments
If no data is set, the default setting is 32-
36 seconds.
START
CM41
CM08
END
CM16
CM19 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 52
Revision 2.0
CALL PARK-SYSTEM
PROGRAMMING
DESCRIPTION DATA
Assign Service Restriction Class (C) to each 
station.• YY = 07
(1) X-XXXX:Station No. 
(2) XX :Service Restriction Class (C)
(00 - 15 )
Assign type of Multiline Terminal to Service 
Restriction Class (C) assigned by CM12 YY = 
07.• YY = 96
(1) XX:Service Restriction Class (C) as-
signed by CM12 YY = 07.
(2) 0: Without LCD
1
:With LCD
Assign the access code for Call Park-System 
set/retrieve.• Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code (6*, 6#)
(2) 008: Call Park-System Set
009: Call Park-System retrieve
Specify the recall timing for Call Park-
System.•Y = 0
(1) 05
(2) 01-98: 4-392 sec. in 4 sec. increments
If no data is set, the default setting is 60-
64 seconds.
Assign a Call Park-System function key to the 
Multiline Terminals with LCD, if required.
Assign a Call Park-System function key to 
SN610 ATTCON, as required. 
(1200 Series Enhancement)• YY = 00
(1) Primary Extension No. +   + Key No.
(2) F5000
• YY=00
(1) ATTCON No. +  + Key No.
(2) F6144: Call Park key
Specify whether a trunk placed on 
consultation hold by Call Park-System can be 
retrieved by pressing a trunk line appearance 
key on a Multiline Terminal.(1) 133
(2) 0/1 : Not Available/Available
START
CM41
CM12
END
CM15
CM20
CM90
CM08
,
, 
						

							ND-45670 (E) CHAPTER 2
Page 153
Revision 2.0
CALL PARK - TENANT
PROGRAMMING
DESCRIPTION DATA
Assign access codes for Call Park-Tenant set/
retrieve.• Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX:Access Code
(2) 062 :Call Park-Tenant Set/Retrieve
Specify whether a trunk placed on 
consultation hold by Call Park-Tenant can be 
retrieved by pressing a trunk-line appearance 
key on a Multiline Terminal.(1) 133
(2) 0/1  : Not Available/Available
Specify the recall timing for Call Park - 
Tenant.•Y = 0
(1) 05
(2) 01-98: 4-392 sec. in 4 sec. increments
If no data is set, the default setting is 60-
64 seconds.
Assign Call Park-Tenant Retrieve keys to the 
Multiline Terminals, as required.• YY = 00
(1) Primary Extension No. +   + Key No. 
(2) F3XX
 X
*a: Group No. (00 - 63)
*b: Serial Key No. (1 - 8)
START
CM90
CM20
END
CM08
CM41
,
*b *a