NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 3 4
Revision 2.0
ANNOUNCEMENT SERVICE
To provide an Internal Recorded Message from a Digital Announcement Trunk (PN-2DATA) in place of Music On
Hold:
DESCRIPTION DATA
Assign a Digital Announcement Trunk Circuit 
No. to the required LEN.
Note:The Digital Announcement Trunk
Circuit No. must be assigned to the
first LEN (Level 0) and/or the third
LEN (Level 2) of each LT slot.(1) LEN (0000-0511) 
(2) EB000-EB127:  Digital Announcement 
Trunk Circuit No.
For PIM0/1: EB000-EB031 
For PIM2/3: EB032-EB063
For PIM4/5: EB064-EB095
For PIM6/7: EB096-EB127 
Define the type of call to be provided with 
Hold Message. •Y = 0
(1) 00:  C.O. Line Call 
01:  Tie Line Call 
02:  Internal Call
(2) 0500:  Hold Message
Assign the function of the Digital 
Announcement Trunk to Hold Message 
Service.• YY = 00
(1) 000-127 : Digital Announcement Trunk 
Circuit No. assigned by CM10 (EB000-
EB127)
(2) 05XX
 :  For Hold Message Service 
*a: Message No. (00-63) 
• YY = 05
(1) 00-63: Tenant No. 
(2) 00-63: Message No. assigned by YY = 
00
To record, replay, or delete a message, assign 
the respective Digital Announcement Trunk 
access code. • Y = 0-3 (Number Plan Group 0-3)
(1) X-XXX (Access Code) 
(2) A00:  Record 
A01:  Replay 
A02:  Delete 
CM10 START
END
CM48
CM49
CM20
*a 
						

							ND-45670 (E) CHAPTER 2
Page 35
Revision 2.0
ANNOUNCEMENT SERVICE
Note 6:A voice message in place of Music-On-Hold can be provided when a call has been placed on hold.
-Different messages can be programmed on a tenant basis.
- Different messages can be programmed, depending on the type of line (CO line, Tie line or station) on
Hold.
- More than one connection can be made to a Digital Announcement Trunk Circuit. Only the first connec-
tion can be assured of hearing the message from the beginning.
- Announcements will be repeated until the call is removed from hold. 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 6
Revision 2.0
ANNOUNCEMENT SERVICE
To provide the Night Announcement by Digital Announcement Trunk (PN-2DATA)
DESCRIPTION DATA
Assign each Digital Announcement Trunk 
Circuit No. to the required LEN.
Note:The Digital Announcement Trunk
Circuit No. must be assigned to the
first LEN (Level 0) and/or the third
LEN (Level 2) of each LT slot.(1) LEN (0000-0511)
(2) EB000-EB127:  Digital Announcement 
Trunk Circuit No.
For PIM0/1: EB000-EB031
For PIM2/3: EB032-EB063 
For PIM4/5: EB064-EB095 
For PIM6/7: EB096-EB127 
Assign the Digital Announcement Trunk 
Circuit No. to each incoming trunk.• YY = 03
(1) 000-255:  Trunk No.
(2) 04:  Direct-In Termination
• YY = 05
(1) 000-255 : Trunk No.
(2) EB000-EB127 : Digital Announcement 
Trunk Circuit No. assigned by CM10.
Assign the function of the Digital 
Announcement Trunk to Night 
Announcement.• YY = 00
(1) 000-127 : Digital Announcement Trunk 
Circuit No. assigned by CM10. (EB000-
EB127)
(2) 03000 : For Night Announcement Ser-
vice
Specify the duration of a Night 
Announcement.•Y = 0
(1) 45
(2) 01-99: 4 -396 sec. in 4sec. increments
If no data is set, the default setting is 60-64 
seconds.
To record, replay, or delete a message, assign 
the respective Digital Announcement Trunk 
Circuit access code. • Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX:  Access Code
(2) A00:  Record 
A01:  Replay 
A02:  Delete 
CM10 START
END
CM30
CM49
CM41
CM20 
						

							ND-45670 (E) CHAPTER 2
Page 37
Revision 2.0
ANNOUNCEMENT SERVICE
Note 7:A voice message can be sent to incoming C.O. lines during night mode. 
- Different messages can be programmed on each C.O. line.
- The voice message can be programmed for day/night. 
- More than one connection can be made to a Digital Announcement Trunk Circuit. Only the first con-
nection can be assured of hearing the message from the beginning.
- Announcements may be programmed to be repeated from 4 to 120 seconds in four-second increments.
HARDWARE REQUIRED 
Digital Announcement Trunk (PN-2DATA). 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 8
Revision 2.0
ANSWER KEY
PROGRAMMING
Note:An ANSWER key is initially assigned on each Multiline Terminal. 
HARDWARE REQUIRED 
ETJ-8-1/ETJ-16DC-1/ETJ-16DD-1/ETJ-24DS-1 and PN-2DLCB/PN-4DLCA card.
DESCRIPTION DATA
Assign the Class of Service for this feature to 
the required Multiline Terminals. • CM12 YY = 02 
(1) X-XXXX:  Primary Extension No. 
(2) XX XX
 
*a: Service Restriction Class (B):  00-
15
• CM15 YY = 72 
(1) XX : Service Restriction Class (B) as-
signed by CM12 YY = 02
(2) 0 : Allowed
START
END
CM12
CM15*a 
						

							ND-45670 (E) CHAPTER 2
Page 39
Revision 2.0
ATTENDANT-ASSISTED CALLING
PROGRAMMING
DESCRIPTION DATA
Assign the Access code for an operator call. • Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX:  Access Code (0) 
(2) 800 
Allocate the ATTCON Group No. to each 
SN610 ATTCON. • YY = 00
(1) 0-7:  ATTCON No. assigned by CM10. 
(2) 0-3:  ATTCON Group No. 
Assign the Master ATTCON within the 
ATTCON Group. • YY = 01
(1) 0-7:  ATTCON No.
(2) 0/1 :  Master/Sub
Specify the tenants to be handled by each ATT 
Group.• Y = 0-3 (ATTCON Group No.0-3 as-
signed by CM60 YY = 00)
(1) 00-63 : Tenant No. 
(2) 0 : To be handled
Specify the Attendant access (ATTCON No. 
0) capability provided from the stations 
belonging to a tenant with no SN610 
ATTCON.(1) 142 
(2) 0/1 :  Allowed/Restricted 
Provide the system with Passing Dial Tone. (1) 048 
(2) 1 :  To be provided
Provide the system with Attendant Night 
Transfer, if required.(1) 018 
(2) 0/1 :  Not to be provided/Provided 
Specify the Individual Attendant access 
capability provided from a station belonging 
to a different tenant. (1) 143 
(2) 0/1 :  Restricted/AllowedCM20 START
END
CM60
CM62
CM08
INITIAL
INITIAL 
						

							CHAPTER 2 ND-45670 (E)
Pag e 4 0
Revision 2.0
ATTENDANT CAMP-ON
PROGRAMMING
To reenter a Camped-On trunk from an Attendant before Automatic Recall (1200 Series Enhancement):
To display the busy station number and name on an Attendant Console when reentering a Camped-On trunk by de-
pressing the loop key (1200 Series Enhancement):
DESCRIPTION DATA
Specify the Camp-On Tone sent to busy 
station.(1) 068 
(2) 0 : Camp-on Tone is sent out only once.
1  :  Camp-on Tone is repeated at an 
interval of 4 seconds.
Specify the recall timing of Camp-On. • Y = 0 
(1) 00
(2) 01-14: 2.4-33.6 sec. in 2.4 sec. 
increments
15-24: 38.4-124.8 sec. in 9.6 sec. 
increments
If no data is set, the default setting is 31.2-33.6 
seconds.
DESCRIPTION DATA
Assign the access code for Call Pickup - 
Direct.• Y=0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code
(2) 021: Call Pickup - Direct
DESCRIPTION DATA
Provide the SN610 ATTCON with the busy 
station number/name display when reentering 
a Camped-On trunk.(1) 441
(2) 0: To be provided
1 : Not to be provided
START
END
CM08
CM41
START
END
CM20
START
END
CM08 
						

							ND-45670 (E) CHAPTER 2
Page 41
Revision 2.0
ATTENDANT CONSOLE (SN610 ATTCON)
PROGRAMMING
DESCRIPTION DATA
Assign the card number of the interface circuit 
for the SN610 ATTCON to its associated 
LEN. (1) 0000-0511 : LEN No.
(2) E000-E007 : ATTCON No.
Set the terminating system for the incoming 
calls to SN610 ATTCON.• YY = 02 (Day mode), YY = 03 (Night 
mode)
(1) Trunk No. (000-255)
(2) 14:  Termination to SN610 ATTCON
Assign the required Attendant Call Selection 
keys and ATTCON Function keys to each 
SN610 ATTCON.
If no data is set, the default setting is as 
follows (Refer to MULTI-FUNCTION KEY 
for assignment of Multi-Function Keys).• YY = 00
(1) ATTCON No. (E000-E007) +   + Key 
No. 
(2) F6000-F6067: Type of Calls to be as-
signed
F6100-F6245: Functions to be assigned CM10
CM30 START
A
CM90
, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 4 2
Revision 2.0
ATTENDANT CONSOLE (SN610 ATTCON)
DESCRIPTION DATA
Note:
ANS or RLS keys can be assigned on
either 25 or 26 by CM60 YY = 15. 
Allocate the ATT Group No. to each SN610 
ATTCON.• YY = 00
(1) ATTCON No. (0-7)
(2) 0:  ATT GROUP 0
3:  ATT GROUP 3
Specify the Master SN610 ATTCON within 
the ATT Group assigned by YY = 00. • YY = 01
(1) ATTCON No. (0-7) 
(2) 0/1 :  Master/Sub
Specify the location of Answer (ANS) and 
Release (RLS) key. • YY = 15
(1) ATTCON No. (0-7)
(2) 0 : Key No.25-Release, Key No.26-An-
swer
1 : Key No.25-Release, Key No.26-
Answer
Specify the tenants to be handled by each ATT 
Group.•Y = 0-3
(1) Tenant No. (00-63)
(2) 0/1 :  To be handled/Not to be handled
END
A
CM62
CM60
Key  No.DataDescription                  
01 F6110 Mode (MODE)
02 F6111 Programming (PROG) 
07-12 F6240-F6245 Loop 1-Loop 6 
16 F6061 Re-Call (RCL)
17 F6060 Operator Call (ATND)
18 F6000 C.O. Incoming 0 
(LDN0)
19 F6200 Source (SRC)
20 F6201 Destination (DEST) 
23 F6204 Hold (HOLD)
24 F6202 Cancel (CANCEL) 
25
NoteAnswer (ANS) 
26 
Note Release (RLS)
LOOP1LOOP2LOOP3LOOP4LOOP5LOOP6
01
AN S
25RLS
26
123
456
78 9
*0#SRC DEST
H O LD C ANC EL MODE PROG
13 1 4
15 1 6
17 1 819 20
21 22
23 24
07
0203040506
08
09101112
AB C D E F
JKL M NO GHI
TUV WX Y PRS
OPER
||
INITIAL
INITIAL 
						

							ND-45670 (E) CHAPTER 2
Page 43
Revision 2.0
ATTENDANT CONSOLE (SN610): ATTENDANT CALLED/CALLING NAME DISPLAY
PROGRAMMING 
DESCRIPTION DATA
Provide the system with the Name Display 
Service. (1) 255 
(2) 1 :  To be provided
Assign the access code for station user name 
entry, used from individual stations.• Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX:  Access Code (62) 
(2) A10 
Assign a Trunk Name Number to each Trunk 
Route. • YY = 03
(1) 00-63 : (Trunk Route No.) 
(2) 00 : Trunk Name No. 00
14 : Trunk Name No. 14 
15  : Kind of Trunk Route assigned by 
CM35 YY = 00 is displayed 
16 : Trunk Name No. 16
63 : Trunk Name No. 63
Assign the desired station user name to each 
station number by Y = 0 or Y = 1.• Y = 0 (By Character Code)
(1) X-XXXX:  Station No. 
(2) Character Code
(20-7F: See Character Code Table) Max. 
16 digits
• Y = 1 (By Character) 
(1) X-XXXX:  Station No. 
(2) Character (A-Z, 0-9)
Max. 8 characters 
Assign the desired trunk name to each trunk 
route by Y = 2 or Y = 3.• Y = 2 (By Character Code)
(1) 00-14, 16-63 (Trunk Name No. assigned 
by CM35 YY = 03.)
(2) Character Code
(20-7F: See Character Code Table) 
Max. 8 digits
• Y = 3 (By Character) 
(1) 00-14, 16-63 (Trunk Name No. assigned 
by CM35 YY = 03.)
(2) Character Code (A-Z, 0-9) 
Max. 4 characters
START
END
CM20
CM35
CM77
CM08
CM77
||
||