NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 3 00
Revision 2.0
MULTILINE TERMINAL ATTENDANT POSITION
DESCRIPTION DATA
Assign a Hotline station to each ICI/OPR 
Line Number. With this assignment, each 
ICI/OPR Line is restricted from call 
origination. •  YY = 03
(1)  ICI/OPR No. (AB00-AB99)
(2) 04: Hotline 
Assign a UCD station to each ICI/OPR Line 
Number. With this assignment, ICI/OPR 
Lines are provided the call-queuing facility 
individually.• Y = 1
(1)  ICI/OPR Line No. (AB00-AB99) 
(2)  1: Pilot Station
• Y = 2
(1)  ICI/OPR Line No. (AB00-AB99) 
(2)  00-15: UCD Group No.
Note: Individual UCD Group Nos. must be 
assigned to each ICI/OPR Line No. 
Assign the access code for Priority Call 0 
(used for Attendant Position access).•  Y = 0-3 (Numbering Plan Group 0-3) 
(1)  X-XXX (Attendant Position Access 
Code)
(2) 088 
Assign the destination of Priority Call 0 to 
each OPR Line. •  YY = 12
(1) Tenant No.
(2)  OPR Line No. (AB00-AB99) 
Destination of Priority Call 0. (1)  250 
(2) 0 
On the required trunks, assign the destination 
of DIT to each ICI Line. •  YY = 02
(1) 000-255 (Trunk Number)
(2)  04: DIT 
•  YY = 04
(1) 000-255 (Trunk Number)
(2)  ICI Line No. (AB00-AB99)
Provide the system with Day/Night Mode 
Change by an NT key on an Attendant 
Position.(1)  244 (Terminating system change) 
(2) 0: Available
(1)  245 (Trunk Restriction Class change)
(2) 0: Available
CM12
CM17
B
A
CM20
CM30
CM08
CM51
CM08 
						

							ND-45670 (E) CHAPTER 2
Page 301
Revision 2.0
MULTILINE TERMINAL ATTENDANT POSITION
DESCRIPTION DATA
Assign the Class of Service for Day/Night 
Mode Change by station-dialing to Attendant. •  CM12 YY = 02 
[Service Restriction Class B (00-15 )] 
•  CM15 YY = 60 
(1)  00-15 (Service Restriction Class B as-
signed by CM12 YY = 02)
(2)  1 : Allowed 
Assign the Loop keys to each Multiline 
Terminal, and assign the function keys 
required for the Attendant Position to the 
Multiline Terminal.•  YY = 00 
(1)  Primary Extension No. +   + Key No. 
(2) AA01-AA75:  Loop Key 
AB00-AB99:  ICI/OPR Key
F1020: Release Key
F0300: Operator Call Key
F0043: Night Key
Specify Line Preselection on a Multiline 
Terminal after pressing the desired LINE/
TRUNK button.
Note:To provide a Trunk Name/Station Name,
refer to Alphanumeric Display.
(1) 199 
(2)  0/1 : Not Required/Required 
B
CM90
CM08
CM12
CM15
END
, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 02
Revision 2.0
MULTILINE TERMINAL ATTENDANT POSITION
If a DSS Console is associated with the Multiline Terminal Attendant Position, add the following system data pro-
gramming.
DESCRIPTION DATA
Assign the DSS Console No. to the required 
LEN. (1) LEN (0000-0511) 
(2)  DSS Console No. (E100-E131)
E100-E107: For PIM0/1 
E108-E115: For PIM2/3 
E116-E123: For PIM4/5 
E124-E131: For PIM6/7 
Assign the Primary Extension No. of the 
Multiline Terminal Attendant Position 
associated with each DSS Console.(1)  DSS Console No. (00-31) assigned by
 CM10 (E100
-E131)
(2)  X-XXXX (Primary Extension No. of
Multiline Terminal Attendant Position) 
Assign Station numbers to the DSS keys. 
Assign the MW, DND, NT keys as function 
keys. (1)  DSS Console No. (00-31) assigned by
CM10 (E100
-E131) 
(2)  For DSS key: 
Key No. (00-29) +  + 
X-XXXX (Station No.)
For Function key: 
Key No. (57-59) +   +
Key data 
*a: F1049: Message Waiting
F1053: Do Not Disturb 
F0043: Night Key
CM10
CM96 START
END
CM97
,
,
*a 
						

							ND-45670 (E) CHAPTER 2
Page 303
Revision 2.0
MULTILINE TERMINAL ATTENDANT POSITION
Example:
Conditions
1. Operator Access Code: 0
2. Primary Extension No.: 200 
3. ICI/Function Keys
- DDD Line: TRUNK 000-004 (ICI Line No. = AB20)
- FX Line: TRUNK 005 (ICI Line No. = AB21) 
- WATS Line: TRUNK 006 (ICI Line No. = AB22) 
- CCSA Line: TRUNK 007 (ICI Line No. = AB23) 
- TIE Line: TRUNK 008-010 (ICI Line No. = AB24)
- OPR Line: Operator Call from Stations (OPR Line No. = AB10)
- OVR Key: Executive Override
- NT Key: Night Key
4. Number of Loop: 5 (Loop Line N. = AA01-AA05) 
5. Tenant No.: 00 
6. Numbering Plan Group: 0
7. Type of Multiline Terminal: ETJ-16DD-1 
:
:
:       
:
:   
L1 L2 L3 L4
L5 OVR NT
DDD FX WATS CCSA
TIE RLS OPR 200
RECALL
FNC
CNF
LNR/SRD
SPKR ANS TRF HOLDL1-L5: Loop Keys
DDD   
FX       
WATS           ICI Keys
CCSA  
TIE   
RLS
OPR
200
OVR
NT   :  Release Key
:  Operator Call Key
:  Primary Extension
:  Executive Right of Way Key
:  Night Key    
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 04
Revision 2.0
MULTILINE TERMINAL ATTENDANT POSITION
Programming for Example:
COMMAND CODE
 1ST DATA
 2ND DATA
 REMARKS
 
11 0000 AA01
0001 AA02
0002 AA03 Loop Line Number
0003 AA04
0004 AA05
0005 AB10 OPR Line Number 
0006 AB20 DDD 
0007 AB21 FX 
0008 AB22 WATS  ICI Line Number
0009 AB23 CCSA
0010 AB24 TIE
12-02 200 1500 Service Class for Attendant Position 
AB10 1501
AB20 1501  
AB21 1501 Service Class for ICI Line
AB22 1501
AB23 1501
AB24 1501
12-03 AA01 08
AA02 08
AA03 08 Service Class for Loop Line
AA04 08
AA05 08
AB10 04
AB20 04
AB21 04 Hotline Assignment
AB22 04
AB23 04
AB24 04
200 15
15-71 00 0 Attendant Position Class
15-73 01 0 ICI/OPR Key Class
17-1 AB10 1
AB20 1
AB21 1  Assign UCD Pilot Station to the ICI/OPR
  AB22 1 Line Numbers. 
AB23 1
AB24 1 
						

							ND-45670 (E) CHAPTER 2
Page 305
Revision 2.0
MULTILINE TERMINAL ATTENDANT POSITION
COMMAND CODE
 1ST DATA
 2ND DATA
 REMARKS
 
17-2 AB10 00
AB20 01
AB21 02 Assign UCD Group to the ICI/OPR Line
 AB22 03 Numbers
AB23 04
AB24 05
20-0 0 088 Operator Access Code
51-12 00 AB10
Operator Call Termination to OPR Line 
08 250 0
30-02 000 04
001 04
002 04
003 04 DIT 
004 04
005 04
006 04
30-04 000 AB20
001 AB20
002 AB20
003 AB20 Incoming Call Termination to ICI Line 
004 AB20
005 AB21
006 AB22
90-00 200,01 AA01
200,02 AA02
200,03 AA03 LOOP Key
200,04 AA04
200,05 AA05
200,07 F0006 OVR Key 
200,08 F0043 NT Key
200,09 AB20 DDD Key 
200,10 AB21 FX Key
200,11 AB22 WATS Key
200,12 AB23 CCSA Key
200,13 AB24 TIE Key 
200,14 F1020 RLS Key
200,15 AB10 OPR Key
200,16 200 Primary Extension Line Key
08 244 0 Definition of NT key function  
08 245 0 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 06
Revision 2.0
MUSIC ON HOLD
PROGRAMMING 
To provide Hold Tone Source on the MP card:
To provide External Hold Tone Source through PN-4COT and PN-DK00 card:
DESCRIPTION DATA
Select the music to be provided. (1) 183 
(2) 0: Nocturne
1 : Minuet 
Define the type of call to be provided with 
Hold Tone on the MP card. 
Note:When using PN-CP03 card, set the
JP1 switch to UP (Internal Hold
Tone Source).•Y = 0
(1) 00: C.O. Line Call
01: Tie Line Call 
02: Internal Call 
(2) 1400: Hold Tone Source on the 
MP card 
DESCRIPTION DATA
Assign the PN-4COT and PN-DK00 for 
interface with External Hold Tone Source to 
the required LENs.
Note 1:The PN-DK00 card No. must be as-
signed to the first LEN (Level 0)
and/or the third LEN (Level 2) of
each LT slot.
Note 2:The PN-4COT Circuit No. must be
assigned for each tenant (One Ex-
ternal Hold Tone Source can be pro-
vided for each tenant).(1) LEN (0000-0511)
(2) DA00-DA09: PN-4COT Circuit No.
Note 2
E800-E831: PN-DK00 Card No.
E800-E807: For PIM0/1
E808-E815: For PIM2/3
E816-E823: For PIM4/5
E824-E831: For PIM6/7
Set the function of External Hold Tone 
Source interface to the PN-DK00 card.(1) XX
 X: 
0-31: Card No. E800-E831 
assigned by CM10
0-3:Circuit No.
(2) 0000-0009
CM08 START
END
CM48
CM10 START
CM44
A 
						

							ND-45670 (E) CHAPTER 2
Page 307
Revision 2.0
MUSIC ON HOLD
For providing Internal Hold Tone generated by DTG:
DESCRIPTION DATA
Define the type of call to be provided with 
External Music.•Y=0
(1) 00: C.O. Line Call
01: Tie Line Call
02: Internal Call
(2) 200: External Hold Tone Source
Specify External Hold Tone Source per each 
tenant.•Y=1
(1) Tenant No. (00-63)
(2) 00-09: External Hold Tone Source No.
Specify which tenant External Hold Tone is 
sent from.(1) 388
(2) 0: Tenant of held station/trunk
1 : Tenant of holding station
DESCRIPTION DATA
Define the type of call to be provided with 
Hold Tone.• Y = 0
(1)  00: C.O. Line Call 
01: Tie Line Call 
02: Internal Call 
(2)  1500: Hold Tone generated by DTG
END
CM48
A
CM64
CM08
CM48 START
END 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 08
Revision 2.0
MUSIC ON HOLD
For providing the Hold Message by Digital Announcement Trunk (PN-2DATA):
DESCRIPTION DATA
Assign a Digital Announcement Trunk 
Circuit No. to the required LEN.
Note:The Digital Announcement Trunk
Circuit No. must be assigned to the
first LEN (Level 0) and/or the third
LEN (Level 2) of each LT slot.(1) LEN (0000-0511)
(2) EB000-EB127: Digital Announcement 
Trunk Circuit No.
For PIM0/1: EB000-EB031 
For PIM2/3: EB032-EB063 
For PIM4/5: EB064-EB095 
For PIM6/7: EB096-EB127
Assign the Class of Service for Digital 
Announcement Trunk Access (Record/
Replay/Delete) to required station.•  CM12 YY = 02 
(1)  X-XXXX: Station No.
(2) XX
 XX 
*a: Service Restriction Class (A) 
•  CM15 YY = 33 
(1)  XX: Service Restriction Class (A) 
assigned by CM12 YY = 02
(2)  1 : Allowed
Define the type of call to be provided with 
Hold Message.• Y = 0
(1)  00: C.O. Line Call
01: Tie Line Call 
02: Internal Call 
(2)  0500: Hold Message
CM10 START
CM48
CM12
CM15
A
*a 
						

							ND-45670 (E) CHAPTER 2
Page 309
Revision 2.0
MUSIC ON HOLD
DESCRIPTION DATA
Assign the data for Hold Message Service to 
the Digital Announcement Trunk Circuit.• YY=00
(1) 000-127: Digital Announcement Trunk 
Circuit No. assigned by CM10 
(EB000-EB127)
(2) 05 XX
: For Hold Message Service
*a 
*a: Message No. (00-63)
• YY=05
(1) Tenant No. (00-63)
(2) Message No. (00-63) assigned by 
YY=00
To record, replay, or delete a message, assign 
the appropriate Digital Announcement Trunk 
access code.• Y=0-3 (Numbering Plan Group 0-3)
X-XXX (Access Code)
(2) A00: Record 
A01: Replay
A02: Delete
CM49
A
END
CM20