NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 2 80
Revision 2.0
MAT: FAULT MESSAGE
PROGRAMMING 
Refer to the Maintenance Manual. 
						

							ND-45670 (E) CHAPTER 2
Page 281
Revision 2.0
MAT: PEG COUNT
PROGRAMMING 
Refer to the Command Manual. (Command Code: B0, B3)  
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 82
Revision 2.0
MAT: REMOVE AND RESTORE
PROGRAMMING 
DESCRIPTION DATA
Set or cancel make-busy to stations and 
trunks. • Y = 0
(1)  X-XXXX: Station Number. 
(2) 0: Make-busy Set
1 : Make-busy cancel 
• Y = 1
(1) 000-255: Trunk Number
(2) 0 : Make-busy Set
1 : Make-busy cancel 
START
END
CME5 
						

							ND-45670 (E) CHAPTER 2
Page 283
Revision 2.0
MAT: STATION/TRUNK STATUS
PROGRAMMING 
Refer to the Maintenance Manual. 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 84
Revision 2.0
MESSAGE CENTER INTERFACE (MCI)
PROGRAMMING
Refer to the Message Center Interface (MCI) System Manual. 
						

							ND-45670 (E) CHAPTER 2
Page 285
Revision 2.0
MESSAGE REMINDER
PROGRAMMING
To provide Message Reminder service for each station:
 
DESCRIPTION DATA
MSG Display. (1) 025
(2) 0/1 : MSG (only) /MSGX (X: No. of 
messages)
To activate the Single-Digit Feature Access 
Code (1, 2, 3 and 6) feature, set the data for 
050, 051, 069 and 148 to “1.”(1)  050: *Button as Switch Hook-Flash.
(2) 1 : Ineffective
(1)  051: #Button as Switch Hook Flash.
(2) 1 : Ineffective
(1)  069 : Single-Digit Dialing/on BT Con-
nection
(2)  1 : Step Call
(1)  148 : Same Last-Digit Redialing on 
BT Connection 
(2) 1 : Ineffective
Provide the system with the Single-Digit 
Feature Access Code on RBT (or Voice Call 
Connection). (1) 156 
(2) 0: Available
Provide the system with the Single-Digit 
Feature Access Code on busy Connection.(1) 208 
(2) 0: Available
Provide the system with the automatic cancel 
of Message Reminder while the called station 
rings. (1) 234 
(2)  0/1 : To be provided/Not to be pro-
vided
Specify the Automatic Cancel of Message 
Reminder when the desired station answers.(1) 235 
(2)  0/1 : To be provided/Not to be pro-
vided
Specify the sending of Special Dial Tone 
(SDT) for SN610 ATTCON or station when 
dialing a feature access code.(1) 236 
(2)  0/1 : Tone is not sent/Tone is sent
Specify the time display for Message 
Reminder service on Multiline Terminals 
with an LCD. (1) 280 
(2) 0/1 : 24-Hour/12-Hour
Specify the Message Waiting Lamp 
indication on the Multiline Terminal to which 
Message Reminder is set. (1) 294 
(2)  0/1 : Flashing (60 IPM)/Lit steady CM08 START
A 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 86
Revision 2.0
MESSAGE REMINDER
HARDWARE REQUIRED 
For providing the Single-Line Telephone with Message-Waiting Lamp:
- PN-4LCD card ´ n/4 (n: Number of Telephone sets equipped with MW Lamp) 
For providing Multiline Terminal
- ETJ-8-1/ETJ-16DC-1/ETJ-16DD-1/ETJ-24DS-1 and PN-2DLCB/PN-4DLCA card. 
DESCRIPTION DATA
Provide the Message Reminder service for 
each station.•  YY = 03
(1)  X-XXXX: Station No. 
(2)  0: To be provided (for stations with 
MW lamp or Multiline Terminals with 
LCD) 
1 : Not Provided 
Assign the Class of Service for Message 
Reminder (Setting Side)/Message Reminder 
(Set Side).•  CM12 YY = 02 (Service Rest. Class A) 
(1)  X-XXXX: Station Number
(2) XX
 XX
*a: Service Restriction Class (A) 
(00-15 ) 
•  CM15 YY = 47 Message Reminder 
(Setting Side) 
•  YY = 48 Message Reminder (Set Side) 
(1)  XX: Service Rest. Class A assigned 
by CM12 YY = 02 
(2) 1 : Allowed 
Assign the access code for Message 
Reminder Search, Retrieve, Set, or Cancel. •  Y = 0-3 Numbering Plan Group (0-3)
(1)  X-XXX: Access Code (*9, #9) 
(2)  A46: Message Reminder Search
A47: Message Reminder Retrieve
A48: Message Reminder Set 
A49: Message Reminder Cancel
Assign the MSG key to each Multiline 
Terminal.•  YY = 00
(1)  Primary Extension No. +  + Key No. 
(2) F1005 
CM13
CM20
END
CM12
CM15
CM90
A
*a
, 
						

							ND-45670 (E) CHAPTER 2
Page 287
Revision 2.0
MESSAGE WAITING
PROGRAMMING
Refer to the DSS/BLF Console feature to program the DSS/BLF as a Message Front Station.
DESCRIPTION
Assign the class of service for Message 
Waiting to required stations as shown below.• CM12 YY=02 [Service Restriction Class 
A (00-15t)] 
• CM15 YY=24 (Administrative
Station allowing Mes-
sage Waiting Set/Reset to 
station) 
• CM15 YY=40 (Station setting MW) 
(1) Service Restriction Class (A) (00-15) 
(2) 0/1 : Restricted/Allowed
Provide each station with Message Waiting 
Service. (Multiline Terminal or Single-Line 
Telephone with Message Waiting Lamp)• YY=03 
(1) X-XXXX: Station No. 
(2) 0: To be provided
Assign an Access Code for Message Waiting 
Set/Reset/Retrieve.• Y=0-3 (Numbering Plan Group 0-3) 
(1) Access Code 
(2) 040: MW Lamp Control-Set 
041: MW Lamp Control-Reset 
A47: MW Retrieve
Assign the Message Front Destination to 
which a call is to be routed by dialing the 
Message Waiting Retrieves access code or 
pressing the Message Waiting key on a 
Multiline Terminal to which Message Waiting 
is set.• YY=15 
(1) Tenant No. (00-63) to which MW set 
Multiline Terminal belongs 
(2) Message Front No. X-XXX (Station 
No./Primary Extension No.) or E000 
(Attendant Console)CM12
CM15
CM13
CM20
CM51
A START
STATION/ADMIN.CM15
YY=24CM15
YY=40
Station w/o MW Lamp
00
Station with MW Lamp 
ETJ-8-1/ETJ-16DC-1/
ETJ-16DD-1/ETJ-24DS-1/SLT01
Administrative station
10 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 88
Revision 2.0
HARDWARE REQUIRED
To provide a Single-Line Telephone with the Message Waiting Lamp:
• PN-4-LCD Card
DESCRIPTION
If an ATTCON is assigned as the Message 
Front destination by CM51 YY=15, set the 
data for 233 to 0. With this setting, Message 
Waiting is automatically reset when the 
ATTCON answers.(1) 233 
(2) 0
To reset the Message Waiting indication while 
the Message Front Station rings by dialing the 
MW Retrieve/Search access code or pressing 
the MW key on a Multiline Terminal, set the 
data for 234 to 0.(1) 234 
(2) 0
To reset the Message Waiting indication when 
the set station answers a second call from the 
Message Front Station, set the data for 235 to 
0.(1) 235 
(2) 0
Assign the Message Waiting function key to 
the Multiline Terminal and the administrative 
station, if provided.• YY=00 
(1) Primary Extension No. +   + Key No. 
(2) For administrative station 
F0040: Message Waiting Set 
F0041: Message Waiting Reset 
For station without MW Lamp 
F1005: Message Waiting Lamp
Select the Dial Tone on Setting Message 
Waiting. (1300 Series Enhancement)•Y=2 
(1) 12 (Dial Tone on Setting Message Wait-
ing) 
(2) 0:  Special Dial Tone (Stutter Dial 
Tone)
1 : Dial ToneCM08
A
CM90
CM48
END
,
INITIAL 
						

							ND-45670 (E) CHAPTER 2
Page 289
Revision 2.0
MISCELLANEOUS TRUNK ACCESS: CODE CALLING EQUIPMENT ACCESS
PROGRAMMING
DESCRIPTION DATA
Assign the interface trunk (PN-4COT and/
PN-DK00) to the required LEN. 
Note:The PN-DK00 Card No. must be as-
signed to the first LEN (Level 0)
and/or the third LEN (Level 2). (1) LEN (0000-0511) 
(2) D000-D255: PN-4COT
E800-E831: PN-DK00
E800-E807: For PIM0/1 
E808-E815: For PIM2/3 
E816-E823: For PIM4/5 
E824-E831: For PIM6/7 
Assign the trunk data to the Trunk Number. •  YY = 00 (Trunk Route Allocation)
(1) Trunk No.
(2)  Route No. (A dedicated route number 
for this service should be assigned.)
•  YY = 01 (Tenant Allocation)
(1) Trunk No.
(2)  Tenant No. (00-63) 
Assign the route data to the trunk route 
specified by CM30 YY = 00. •  YY = 00 (Kind of Route)
(1)  Route No. (00-63) 
(2) 05
•  YY = 01 (Type of Signal to be sent out.) 
(1)  Route No. (00-63)
(2) 2: DP 
4: DTMF 
•  YY = 08 (Dial Pulse Sending) 
(1)  Route No. (00-63) 
(2)  3 : To be sent 
CM10 START
CM35
CM30
A