NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 1 64
Revision 2.0
CLASS OF SERVICE
PROGRAMMING
To assign the Telephone Class:
DESCRIPTION DATA
Assign the Telephone Class to each station.  • YY = 00 (Type of Telephone)
(1) Station Number (X-XXXX) 
(2) 1 : DP (Rotary Dial Telephone) 
3
:DTMF (Push Button Tele-
phone)/DP
• YY = 03 (Telephone Class)
(1) Station Number (X-XXXX)
(2) 00: House Phone 0 
01: House Phone 1
02: House Phone 2
03: House Phone 3
04: Hot Line 
05: Automatic Intercom 
06: Manual Intercom
07: Dial Intercom
08: Attendant Position Loop Line 
15  Ordinary Station 
CM12 START
END 
						

							ND-45670 (E) CHAPTER 2
Page 165
Revision 2.0
CLASS OF SERVICE
To assign the Trunk Restriction Class:
DESCRIPTION DATA
Assign the Trunk Restriction Class to each 
station. • YY = 01 (Trunk Restriction Class)
(1) Station Number (X-XXXX) 
(2) X
 X
*a: Trunk Rest. Class in Day mode 
(1 -8)
*b: Trunk Rest. Class in Night mode 
(1 -8)
1: Unrestricted (RCA)
2: Non-Restricted 1 (RCB)
3: Non-Restricted 2 (RCC)
4: Semi-Restricted 1 (RCD) 
5: Semi-Restricted 2 (RCE) 
6: Restricted 1 (RCF)
7: Restricted 2 (RCG)
8: Fully-Restricted (RCH) 
Set the Outgoing/Incoming Trunk Route 
Restriction Data by Trunk Restriction 
Classes (RCA-RCH).• YY = 51-58 (Outgoing Trunk Rest. 
Data)
• YY = 61-68 (Incoming Trunk Rest. 
Data)
(1) Trunk Route No. (00-63)
(2) 0/1  Restricted/Allowed
CM12
CM35 START
END
*b *a 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 66
Revision 2.0
CLASS OF SERVICE
To assign the Service Feature Class:
DESCRIPTION DATA
Assign the required Service Feature Class to 
each station.
Service Feature categories for each class are 
specified by CM15.• YY = 02 (Service Rest. Class - A/B)
(1) Station Number (X-XXXX) 
(2) XX
 XX
*a: Service Restriction Class A 
(00-15 ) 
*b: Service Restriction Class B 
(00-15 ) 
• YY =07 Service Restriction Class C 
(00-15)
(1) Station Number (X-XXXX)
(2) XX
*a: Service Restriction Class C (00-15t) 
Specify the service features in each Service 
Class A, B, and C. • Service Class A (YY = 00-49, 
YYY = 100-104)
• Service Class B (YY = 53-73) 
(1) XX [Service Restriction Class (A), (B) 
00-15]
(2) 0/1  Restricted/Allowed
• Service Class C
YY = 80 
(1) XX: 00-15 
(2) 0/1  Restricted/Allowed 
YY = 82 
(1) XX: 00-15 
(2) 0/1  Allowed/Restricted 
YY = 83, 84 
(1) XX: 00-15 
(2) 0/1  Note 1
 
YY = 88, 89 
(1) XX: 00-15 
(2) 0/1  Note 2
 
YY = 90, 91 
(1) XX: 00-15 
(2) 0/1  Note 3
 
YY = 96 
(1) XX: 00-15 
(2) 0/1  Without LCD/With LCD
YY = 97, 98 
(1) XX: 00-15 
(2) 0/1  Note 4
 
CM12
CM15 START
END
*b *a
*a 
						

							ND-45670 (E) CHAPTER 2
Page 167
Revision 2.0
CLASS OF SERVICE
Note 1:Tone indication pattern is assigned by the combination of data for YY =83,84. 
Note 2:Result of Switch Hook Flash during station-to-station call is specified by the combination of data for 
YY = 88, 89. 
Note 3:Result of Switch Hook Flash during C.O. line Connection specified by the combination of data for 
YY = 90, 91. 
Note 4:Service for a Off Hook Alarm call which encounters the terminating station busy is specified by the 
combination of data for YY = 97, 98.
: Initial Data
YY 83 84 MEANING OF DATA
Setting Data0 0 600 +700 [Hz]
1 0 1024 +1285 [Hz] ´16 [Hz] Modulating Signal
0 1 480 + 606 [Hz] ´ 8 [Hz] Modulating Signal
1 1 480 +606 [Hz] ´ l6 [Hz] Modulating Signal
: Initial Data
88 89 MEANING OF DATA
1 1 Effective (Special Dial Tone Connection)
0 1 Ineffective 
0 0 Attendant Recall
: Initial Data
90 91 MEANING OF DATA
1 1 Effective (Special Dial Tone Connection)
0 1 Ineffective 
0 0 Attendant Recall
: Initial Data
97 98 MEANING OF DATA
0 0 Call Waiting  (When UCD Pilot Station and CM08-212 = 0) 
0 1 UCD (When UCD Pilot Station and CM08-212 = 1)
1 0 Call Waiting  (When Ordinary Station) 
1 1 Hunting (When Ordinary Station) 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 68
Revision 2.0
CODE RESTRICTION
PROGRAMMING
DESCRIPTION DATA
Provide the system with the Tol1 Restriction 
feature for an outgoing call by System Speed 
Dialing/Station Speed Dialing, if desired.(1) 035 (Station Speed Dialing) 
(2) 0/1  Not to be provided/To be 
provided
(1) 044 (System Speed Dialing)
(2) 0/1  Not to be provided/To be 
provided
Provide the system with Toll Diversion or 
Toll Denial.(1) 119 
(2) 0/1  Toll Diversion (Routed to the 
“ICPT” key on the ATTCON)/
Toll Denial (Routed to Reorder 
Tone)
Assign a Trunk Restriction Class to each 
station. • YY = 01
(1) X-XXXX (Station No.)
(2) X
 X (Trunk Restriction Class)
*a: 1-8 (In Day Mode) 
1  Unrestricted (RCA) 
2: Non-Restricted 1 (RCB) 
3: Non-Restricted 2 (RCC) 
4: Semi-Restricted 1 (RCD)
5: Semi-Restricted 2 (RCE)
*b: 1-8 (In Night Mode) 
Assign the data for Dial Pulse sending to the 
Route No. assigned. • YY = 08 (Dial Pulse Sending) 
(1) Trunk Route No. (00-63)
(2) 3  To be sent. 
Provide the Toll Restriction feature to the 
required trunk routes.• YY = 11
(1) Trunk Route No. (00-63) (00)
(2) 0: To be provided 
Specify outgoing route access capability for 
each restriction class.• YY = 51-55 
(1) Trunk Route No. (00-63) 
(2) 0/1  Restricted/Allowed 
Assign the Area Code Development Pattern 
No. for Toll Restriction and Maximum Digit 
Analysis to each trunk route. • YY = 76
(1) Trunk Route No. (00-63) 
(2) 00-04 [Area Code Development Pattern 
(No. 0-4)] 
CM08
CM12 START
CM35
A
*b *a 
						

							ND-45670 (E) CHAPTER 2
Page 169
Revision 2.0
CODE RESTRICTION
DESCRIPTION DATA
Assign the Toll Restriction Patterns with five 
kinds of Trunk Restriction Classes assigned 
by CM12 YY = 01. Toll Restriction Pattern 
00-15 are preassigned as shown below. If a 
new Restriction Pattern is required, change 
the data for Restriction Patterns 01-13 (00, 14 
and 15 are fixed).• YY = 01-13 (Toll Restriction Pattern 
No. 01-13)
(1) Trunk Restriction Class (1-5) 
(2) 0: Restricted 
3: Allowed
Specify the maximum number of digits to be 
dialed during an outgoing call. The 
maximum number of digits, including the 
area codes, should be assigned to each area 
code.• Y =0-4 (Area Code Development Pat-
tern No. 0-4 assigned by CM35 YY = 
76) 
(1) X-X...X (Area Code dialed, Max. 8 dig-
its)
(2) 01: 1 digit 
24  24 digits 
79: 79 digits CM81
B
A
CM85
YYTRUNK
RESTRICTION
CLASS01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00
TOLL RESTRICTION PATTERN NUMBER ON EACH TRUNK RESTRICTION CLASS
1
2
3
4
5RCA
RCB
RCC
RCD
RCE3
3
3
3
30
0
0
0
03
3
3
0
03
3
0
0
03
0
0
0
00
0
0
0
00
0
0
0
00
0
0
0
03
3
3
0
03
3
0
0
03
0
0
0
03
0
0
0
03
0
0
0
00
0
0
0
03
3
3
3
30
0
0
0
0
0:
3:Restricted
Allowed 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 70
Revision 2.0
CODE RESTRICTION
DESCRIPTION DATA
Assign the area code to be restricted and the 
Trunk Restriction Pattern No. assigned by 
CM81 to the Area Code Development Pattern 
No. assigned by CM35 YY = 76. For 
example, to provide the Trunk Restriction 
Class “RCB, RCC, RCD, and RCE” with the 
Toll Restriction for Area Code “00”: 
• Area Code = 00 
• Trunk Restriction Pattern = 05 
(See Toll Restriction Pattern Table on
CM81.) 
If the Toll Restriction Pattern for the same 
area code is changed according to the Tenant, 
Date, and Time, assign the required patterns 
(Tenant, Date, and Time) to the area code.• YYY = 400-404 (Area Code Develop-
ment No. 0-4) 
(1) Area Code (Max. 8 digits) 
(2) 900-915 (Trunk Restriction Pattern 
00-15)
Note:For details of Resident System
Program, refer to the Command
Manual.
CM8A
C
B
AREA
CODE400
 
404
DATE
PATTERN 200
-207
 300
-303 100
-115
TENANT
PATTERN TIME
PATTERN
 000
-063
ROUTE
PATTERN
 500
-755
TR
PATTERN TRUNK REST. 
PATTERN 00-15 
						

							ND-45670 (E) CHAPTER 2
Page 171
Revision 2.0
CODE RESTRICTION
DESCRIPTION DATA
To add a Tenant Pattern:
STEP 1
Assign the area code to be 
restricted and a Tenant Pattern 
No. to the Area Code Develop-
ment Pattern No. assigned by 
CM35 YY = 76. • YYY =400-404 (Area Code Develop-
ment Pattern No.)
(1) Area Code (Max. 8 digits)
(2) 100-115 (Tenant Pattern No. 00-15) 
STEP 2
Assign a Tenant No. and the 
Route Pattern No. to the Tenant 
Pattern No. assigned by Step1.• YYY =100-115 (Tenant Pattern No. 00-
15) 
(1) 00-63 (Tenant No. 00-63) 
(2) 00-63 (Route Pattern No. 00-63) 
STEP 3
Assign a TR Pattern No. to the 
Route Pattern No. assigned by 
Step 2.• YYY = 000-063 (Route Pattern No. 
00-63) 
(1) 1 
(2) XXX
 00 (TR Pattern No.)
*a: TR Pattern No. 000-255
STEP 4
Assign a Trunk Restriction Pat-
tern No. assigned by CM81 to the 
TR Pattern No. assigned by Step 
3. • YYY = 500-755 (TR Pattern No.) 
(1) 000 
(2) 00-15 (Trunk Restriction Pattern No. 
00-15)
To add a Time and Date Pattern: 
STEP 1
Assign the area code to be 
restricted and a Date Pattern No. 
to the Area Code Development 
Pattern No. assigned by CM35 YY 
= 76. • YYY = 400-404
(1) Area Code (Max. 8 digits)
(2) 300-303 (Date Pattern No. 00-03) 
STEP 2
Assign a date and Time Pattern 
No. 00-07 to the Date Pattern No. 
assigned by Step 1.
Set the data for all dates, one by 
one, for which Toll Restriction is 
to be applied.• YYY =300-303 (Date Pattern No. 
00-03)
(1) 0-6 (Date)
0: Sunday 
1: Monday 
2: Tuesday 
3: Wednesday 
4: Thursday 
5: Friday 
6: Saturday 
(2) 200-207 (Time Pattern No. 00-07) 
CM8A
D
C
*a 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 72
Revision 2.0
CODE RESTRICTION
DESCRIPTION DATA
STEP 3 Assign the starting time for the 
Toll Restriction and Route Pattern 
No. to the Time Pattern No. 
assigned by above Step 2. 
Set the Starting Time as shown 
below. 
Note:
Two times must be set. The first to 
start Toll Restriction and the sec-
ond to stop it (or change it back).• YYY = 200-207 (Time Pattern No. 
00-07)
(1) XXXX (Time to Change) 
XX
 XX 
*a: Hours (00-23) 
*b: Minutes (00/30)
(2) 000-063 (Route Pattern No. 00-63)
If Tenant Pattern is required, set 100-
115 (Tenant Pattern No. 00-15)
STEP 4
  Assign the TR Pattern No. to the 
Route Pattern No. assigned by 
Step 3.• YYY = 000-063 (Route Pattern No. 
00-63)
(1) 1 
(2) XXX
 00 (TR Pattern No.)
*a: TR Pattern No. 000-255 
STEP 5
Assign the Trunk Restriction Pat-
tern No. assigned by CM81 to the 
TR Pattern No. assigned by Step 
4.• YYY = 500-755 (TR Pattern No. 000-
255)
(1) 000 
(2) 00-15 (Trunk Restriction Pattern No. 
00-15)
D
END
*a *b
*a 
						

							ND-45670 (E) CHAPTER 2
Page 173
Revision 2.0
CONFERENCE
PROGRAMMING
DESCRIPTION DATA
Provide the system with three-party 
conference. (1) 101 
(2) 1 : Three Party Conference among 
stations. 
(1) 102 
(2) 0: As per 101 
(1) 103 
(2) 0: As per 104 
(1) 104 
(2) 1 : Three Party Conference among 
stations and Trunk Call.
Provide the system with a four-party 
conference.
Note:This feature can only be activated
from a Multiline Terminal.(1) 246 
(2) 1 : Four Party Conference
Provide the system with additional CFT, if 
required.• Y = 6 (Make Busy)
(1) 08-15 (Additional CFT Circuit No.)
(2) 1: Make Busy Off
• Y = 7 (Purpose of the CFT) 
(1) 08-15 (Additional CFT Circuit No.)
(2) 1: For both ATTCON and stations 
CM08
CM45 START
END