NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 4 02
Revision 2.0
TRUNK-TO-TRUNK CONNECTION
DESCRIPTION DATA
Assign the Service Restriction Class C to each 
station.• YY = 07
(1) X-XXXX:Primary Extension No.
(2) XX:Service Restriction Class C (00-15)
Provide the switch hook flash capability dur-
ing C.O. line connection, to the required sta-
tions.• YY = 90, 91
(1) 00-15:Service Restriction Class C
(2) 1 :Allowed
Specify the combination of trunk routes al-
lowing the Trunk to Trunk Connection.(1) XX
 XX
Incoming trunk route 00-63
Outgoing trunk route 00-63
(2) 0/1 : Allowed/Restricted
Provide the system with Ring Transfer for 
Call Transfer-All Calls to a trunk when a sta-
tion holds another station or trunk.(1) 253
(2) 0: Allowed
Provide the system with forced disconnection 
when a tandem call duration passes a predeter-
mined time.(1) 029
(2) 0/1 : Available/Not available
Allow or restrict forced disconnection of tan-
dem connection for the incoming trunk route.
This data is available when CM08-029 is set 
to 0.• YYY = 119
(1) 00-63:Trunk route No.
(2) 0/1 :Allowed/Restricted
Specify the forced disconnection timing for 
tandem call.•Y = 0
(1) 54
(2) 01-06:64-224 min.
(32 min. increments)
If no data is set, the default setting is 128 min.
CM12
A
CM08
CM35
CM15
CM36
CM41 START 
						

							ND-45670 (E) CHAPTER 2
Page 403
Revision 2.0
TRUNK-TO-TRUNK CONNECTION
DESCRIPTION DATA
Provide the system with Trunk to Trunk Con-
nection when no release signal arrives from 
the incoming trunk route and answer signal ar-
rives from the outgoing trunk route.(1) 324
(2) 0/1 :Available/Not available
Provide the system with Trunk to Trunk Con-
nection transferred by a station or an atten-
dant, when no answer signal arrives and 
release signal arrives from the outgoing trunk 
route.(1) 028
(2) 0/1 :Available/Not available
Specify the forced disconnection timing for 
tandem connection when the called party does 
not answer.
This data is available when no release signal 
arrives from incoming trunk route.•Y = 0
(1) 55
(2) 01-13:12-60 sec.
(4 sec. increments)
If no data is set, the default setting is 20-24 
sec.
CM41
END
CM08
A 
						

							CHAPTER 2 ND-45670 (E)
Pag e 4 04
Revision 2.0
TRUNK-TO-TRUNK CONNECTION
To provide the AMP trunk for Trunk-to-Trunk Connection (1500 Series Enhancement):
DESCRIPTION DATA
Assign the Card Number of the AMP trunk 
(PN-2AMP).
Maximum of two digits are available.
Note:The AMP card number must be
assigned to both of the first LEN
(Level 0) and the third LEN (Level 2)
of each slot.(1) LEN (0000-0511)
(2) Card No. of AMP trunk
C100-C115 : For PIM0/1
C116-C131 : For PIM2/3
C132-C147 : For PIM4/5
C148-C163 : For PIM6/7
Assign the AMP patterns to each combination 
of the trunk routes.• YY = 00
(1) XX
 XX
Incoming trunk route 00-63
Outgoing trunk route 00-63
(2) 00-14:AMP pattern No. 00-14
15 :  Not use the AMP trunk
Assign the gain value of each AMP pattern. • YY = 01
(1) 00-14: AMP pattern No. 00-14
(2) X
 X
Fixed gain
0 : 12 dB
1 : 8 dB
2 : 4 dB
3 : 0 dB
AGC (Automatic Gain Control)
0 : 0 dBr
1:+4 dBr
2 : –4 dBr
3  : Through (assigned by
Fixed Gain)
Assign the Echo Canceller function to each 
AMP pattern.• YY = 02
(1) 00-14:AMP pattern No. 00-14
(2) 0:Through
1 : Normal
Assign the Gain Controller of Echo Canceller 
to each AMP pattern.• YY = 03
(1) 00-14: AMP pattern No. 00-14
(2) 0 :ON
1:OFF
CM10
A
CM38 START 
						

							ND-45670 (E) CHAPTER 2
Page 405
Revision 2.0
TRUNK-TO-TRUNK CONNECTION
DESCRIPTION DATA
Select the Tone Disabler’s mode on each AMP 
pattern.• YY=04
(1) 00-14: AMP pattern No. 00-14
(2) 0:G164
1 : G165
Specify the Detect Timing of Tone Disabler on 
each AMP pattern.• YY=05
(1) 00-14: AMP pattern No. 00-14
(2) 0:0 sec.
1 : 2 sec.
Specify the channels connected to each AMP 
pattern.• YY=06
(1) 00-14: AMP pattern No. 00-14
(2) 0:Incoming route: Tie Line
Outgoing route: C.O. Line
1 :Incoming route: C.O. Line
Outgoing route: Tie Line
Specify the Timing of AMP trunk connection 
on each AMP pattern.• YY=07
(1) 00-14: AMP pattern No. 00-14
(2) 0:When dialing is finished
1 :When answering
CM38
C
END 
						

							CHAPTER 2 ND-45670 (E)
Pag e 4 06
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
PROGRAMMING
To activate UCD:
DESCRIPTION DATA
For each UCD Group, assign station numbers, 
one by one, in the order of hunting. 
Note:Up to 60 stations can be assigned
into a single UCD group.
Example:
 For setting Station Numbers 200, 
201, 202 into one UCD Group. 
1st Operation (1) 200 
(2) 200
2nd Operation(1) 201
(2) 202
3rd Operation (1) 202
(2) 200•Y = 0
(1) X-XXXX (Station No.)
(2) X-XXXX (Another Station No. to be 
linked) 
Assign the Pilot Station and Member Station. • Y = 1
(1) X-XXXX (UCD Station No.) 
(2) 1/0 : Pilot Station/Member Station 
Assign the UCD Group Number. • Y = 2
(1) X-XXXX (UCD Station No.) 
(2) 00-15 (UCD Group 00-15)
Specify the UCD service for each type of call. • Y = 4 (Internal Call: from station/AT-
TCON) 
(1) X-XXXX (Pilot Station No. of the UCD 
Group)
(2) 0/1 : Not to be provided/To be provid-
ed 
• Y = 5 (C.O. Incoming Call: DDD: FX/
WATS) 
(1) X-XXXX (Pilot Station No. of the UCD 
Group)
(2) 0/1 : Not to be provided/To be provid-
ed
CM17 START
A
3rd 1st
2nd 200
202 201 
						

							ND-45670 (E) CHAPTER 2
Page 407
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
DESCRIPTION DATA
• Y = 6 (Tie Line Incoming Call) 
(1) X-XXXX (Pilot Station No. of the UCD 
Group)
(2) 0/1 : Not to be provided/To be provid-
ed 
• Y = 7 (DID Call) 
(1) X-XXXX (Pilot Station No. of the UCD 
Group)
(2) 0/1 :Not to be provided/To be 
provided
• Y=B (Designation of the number of 
queuing in each UCD group)
(1) X-XXXX (Pilot Station No. of the UCD 
Group)
(2) 0/1 : To be provided (See CM42-16)/
Not to be provided
Specify the maximum number of queuing in 
each UCD group.(1) 16
(2) 01-99 (Number of queuing in each UCD 
group)
Specify the basic call answer delay time for 
use in PEG Count analysis.•Y = 0
(1) 16
(2) 01-30 : 4-120 sec. in 4 sec. increments
If no data is set, the default setting is 32-36
seconds.
Assign the access code for UCD Station Busy-
Out Set and Reset.• Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX (Access Code)
(2) 044: Busy-Out Set
045: Busy-Out Reset
Assign the UCD Busy-Out key on the 
Multiline Terminal, if required.• YY = 00
(1) Primary Extension No. +    + Key No. 
(2) F0044: UCD Busy-Out
Assign the Release key on the Multiline 
Terminal, if required.• YY = 00
(1) Primary Extension No. +   + Key No. 
(2) F1020: Release 
B
A
CM41
CM20
CM90
CM17
CM42
,
, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 4 08
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
DESCRIPTION DATA
Specify the processing for an incoming call 
when all UCD Stations are busy.(1) 212 
(2) 0/1 :Busy Tone Connection /Queuing
Specify the processing for a held call after set-
ting the UCD Busy-Out.(1) 214 (For the held Call from Tie Line)
(2) 0/1 :Reconnected by Switch Hook 
Flash/Disconnected 
(1) 215 (For the held call from C.O. Line)
(2) 0/1 :Reconnected by Switch Hook 
Flash/Disconnected
Specify that the transferred C.O. call from a 
station or SN610 ATTCON is placed into 
queuing mode when all UCD stations are 
busy.
Note:This data is only effective when
CM08-212 is set to 1. (1) 227 
(2) 0: The call is placed into queuing mode. 
Note
1 : Recall to the transferring station 
(when the call is transferred from 
station) or attendant Camp-On is 
set (when the call is transferred 
from ATTCON).
Enable the UCD Busy-Out set and reset from 
the secondary extension.
(1200 Series Enhancement)(1) 442 
(2) 0/1 : Available/Not Available
B
END
CM08 
						

							ND-45670 (E) CHAPTER 2
Page 409
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
To provide the delay announcement for UCD:
DESCRIPTION DATA
Assign a Digital Announcement Trunk Cir-
cuit No. to each LEN No.(1) 0000-0511 (LEN No.)
(2) EB000-EB127 (Digital Announcement 
Trunk Circuit No.)
Assign the Class of Service for Digital An-
nouncement Trunk Access (Record/Replay/
Delete) to the required station.• CM12 YY=02
(1) X-XXXX: Station No.
(2) XX
XX
*a 
*a: Service Restriction Class (A)
(00-15 )
• CM15 YY=33
(1) XX: Service Restriction Class (A) 
assigned by CM12 YY=02
(2) 1 : Allowed
Specify the pattern of the message sent to 
each UCD group.•Y = A
(1) X-XXXX: Pilot Station number of the 
UCD Group
(2) 0: To be sent periodically
1 : To be sent only once.
If the data for CM17 Y = A is “0”, set the in-
terval time for UCD Delay Announcement.•Y = 0
(1) 47
(2) 01-30 : 4-120 sec. in 4 sec. increments
If no data is set, the default setting is 32-36 sec-
onds.
Define the maximum waiting time of a UCD 
Call for the UCD PEG Count. This timing is 
also applied to the duration of Ringback 
Tone after a call arrives before the first Delay 
Announcement answers the call.•Y = 0
(1) 16
(2) 01-30 : 4-120 sec. in 4 sec. increments
If no data is set, the default setting is 32-36 sec-
onds.
Assign the UCD Delay Announcement func-
tion to the required Digital Announcement 
Trunk Circuit.• YY = 00
(1) 000-127 (Digital Announcement Trunk 
Circuit No.)
(2) 0B0XX
: UCD Delay Announcement
11XX
: UCD Second Delay Announcment
*a: UCD Group No. (00-15)-
START
CM10
CM17
CM41
CM49
CM12
CM15
A
*a
*a 
						

							CHAPTER 2 ND-45670 (E)
Pag e 4 10
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
DESCRIPTION DATA
Assign an access code to record, replay, and 
delete the Digital Announcement Trunk.• Y=0-3 (Numbering Plan Group 0-3)
(1) X-XXXX: Access code
(2) A00: Record
A01: Replay
A02: Delete
When transferring the call to an extension or 
Attendant after the 1st interval time of UCD 
Delay Announcement, assign the destination.
Note:This command is only effective when
CM17, Y=A is set to 0 (to be sent pe-
riodically).•Y=17
(1) 00-63: Tenant No.
(2) Destination: 
X-XXXX: Station No. or E000: SN610
ATTCON
Specify a diversion display on a transferred 
destination (Multiline Terminal or SN610 AT-
TCON).(1) 357
(2) 0/1 : Available/Not Available
CM20
A
END
CM51
CM08 
						

							ND-45670 (E) CHAPTER 2
Page 411
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
To monitor a UCD call, with or without a Warning Tone:
DESCRIPTION DATA
Specify the warning tone sent to connected 
parties (in two-way calling) when monitoring.(1) 259 
(2) 0: No Tone
1 : One Warning Tone 
Assign the Class of Service for monitoring 
stations. • CM12 YY = 02 
(1) X-XXXX: Station number
(2) XX
XX
*a: Service Restriction Class (A) (00-
15 )
• CM15 YYY = 103 
(1) XX: [Service Restriction Class (A) 00-
15] assigned by CM12 YY = 02 
(2) 1 : Allowed
Assign the Class of Service for monitored sta-
tions. 
Note:Monitoring telephone conversations
may be illegal under certain circum-
stances and laws. Consult a legal ad-
visor before implementing the
monitoring of telephone conversa-
tions. Some federal and state laws re-
quire a party monitoring a telephone
conversation to use beep-tone(s), to
notify all parties to the telephone
conversation, and/or obtain consent
from all parties to the telephone con-
versation. Some of these laws pro-
vide strict penalties for illegal
monitoring of telephone conversa-
tions.• CM12 YY = 02 
(1) X-XXXX: Station number 
(2) XX
XX 
*a: Service Restriction Class (A) (00-
15 ) 
• CM15 YYY = 104 
(1) XX: [Service Restriction Class (A) 00-
15] assigned by CM12 YY = 02
(2) 1 : Allowed
Assign the access code for monitoring, if re-
quired. • Y = 0-3 (Number Plan Group 0-3)
(1) X-XXX: Access Code
(2) 033: Monitor
Assign a monitoring function key to the re-
quired multiline terminals. • YY = 00
(1) X-XXX: (Primary Ext. No.) + + Key 
No. (01-16) 
(2) F0033: Monitor
START
CM08
CM20
CM90
CM12
CM15
CM12
CM15
END
*a
*a
,