NEC Neax2000 Ivs Feature Programming Manual
Have a look at the manual NEC Neax2000 Ivs Feature Programming Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 2 ND-45670 (E)
Pag e 4 4
Revision 2.0
ATTENDANT CONSOLE (SN610): ATTENDANT CALLED/CALLING NAME DISPLAY
Character Code Table
234567
0
0@P \ p
1!1AQaq
2”2BRb r
3#3CSc s
4$4DTd t
5%5 EU e u
6&6 FV f v
7’7GWgw
8(8HXhx
9)9IYiy
A*: JZjz
B+;K[k{
C,N^n®
F/?O_o¬
1ST
2ND
ND-45670 (E) CHAPTER 2 Page 45 Revision 2.0 ATTENDANT CONSOLE (SN610): ATTENDANT CALL SELECTION PROGRAMMING DESCRIPTION DATA Specify the ATT call Selection key to which incoming calls from each trunk route terminate.• YY = 15 (1) Trunk Route No. (00-15) (2) ATT Call Selection Key: 00-07: C.O. Incoming Call 0-7 10-17: FX Incoming Call 0-7 20-27: WATS Incoming Call 0-7 30-37: CCSA Incoming Call 0-7 40-47: Tie Line Incoming Call 0-7 Assign the ATT Call Selection Keys required. The following ATT Call Selection Keys are initially set.• YY = 00 (1) ATTCON No. + + Key No. (2) F60XX *a: 00-07 (C.O. Incoming Call 0-7) 10-17 (FX Incoming Call 0-7) 20-27 (WATS Incoming Call 0-7) 30-37 (CCSA Incoming Call 0-7) 40-47 (Tie Line Incoming Call 0-7) 50-53 (Special Operator Call 0-3) 54 (Priority Call 0) 55 (Priority Call 1) 56 (Emergency Call) 60 (Operator Call) 61 (Recall) 62 (Serial Call) 63 (Call Forwarding-No Answer) 64 (Call Forwarding-Busy Line) 65 (Call Forwarding-Intercept) 66 (Off Hook Alarm) 67 (Inter Position Calling/Transfer) START END CM35 CM90 Key No.DataDescription 16 F6061 Recall (RCL) 17 F6060 Operator Call (ATND) 18 F6000 C.O. Incoming 0 (LND0) LO O P1LOOP2LOOP3LOOP4LOOP5LO O P6 01 AN S 25RLS 26 123 456 78 9 *0#SRC DEST H O LD C ANC EL MODE PROG 13 14 15 16 17 1819 20 21 22 23 24 07 0203040506 08 09101112 AB C D E F JKL M N O GHI TU V W X Y PRS OPER , *a
CHAPTER 2 ND-45670 (E) Pag e 4 6 Revision 2.0 ATTENDANT CONSOLE (SN610): ATTENDANT CONSOLE LOCKOUT-PASSWORD PROGRAMMING DESCRIPTION DATA Assign the Mode key for providing Attendant Console Lockout on the SN610 ATTCON.• YY = 00 (1) ATTCON No. + + Key No. (2) F6110 Assign the access code for providing Attendant Console Lockout for an SN610 ATTCON, if required.• Y = 0-3 (Numbering Plan Group 0-3) (1) X-XXX (Access Code) (2) A55 Specify the buzzer sound when terminating an incoming call to the SN610 ATTCON in Attendant Console Lockout.(1) 353 (2) 0/1 : Not to be provided/To be provided Assign the password code for Attendant Console Lockout. • YY = 30 (1) 0 (2) XX-XX : Password Code (Max. 8 digits) X : 0-9, A (*) B (#) If no data is set, the default setting is NONE. In this case, the password is set to “12345678”. END CM20 CM08 CM60 CM90 START, INITIAL
ND-45670 (E) CHAPTER 2 Page 47 Revision 2.0 ATTENDANT CONSOLE (SN610): ATTENDANT DO NOT DISTURB SETUP AND CANCEL PROGRAMMING DESCRIPTION DATA Assign Do Not Disturb-System to the required stations.• YY = 00 (1) X-XXXX (Station No.) (2) 0: To be provided Assign DND and DNDOVR function keys to each SN610 ATTCON, if needed. Note:By resident system program, the Multi-Function keys are programmed to provide a DND OVR key when the ATTCON calls a station in DND. • YY = 00 (1) ATTCON No. + + Key No. (2) F6102: DND F6108: DND Override F6104: RESET END CM90 CM13 START ,
CHAPTER 2 ND-45670 (E) Pag e 4 8 Revision 2.0 ATTENDANT CONSOLE (SN610): ATTENDANT INTERPOSITION CALLING/TRANSFER PROGRAMMING DESCRIPTION DATA Assign the access code for Inter-Position Transfer. • Y = 0-3 (Numbering Plan Group 0-3) (1) X-XXX (Access Code) (2) 095 Assign the Attendant Call Selection Key for this feature on the SN610 ATTCON. • YY = 00 (1) ATTCON No. + + Key No. (2) F6067 Specify the Inter-Position Transferred call to another tenant’s SN610 Attendant Console. If the data is set to 1, a call from any station can be transferred to another SN610 Attendant Console regardless of Tenant Allocation by CM62. (1) 143 (2) 0/1 : Restricted/Allowed END CM90 CM08 CM20 START ,
ND-45670 (E) CHAPTER 2 Page 49 Revision 2.0 ATTENDANT CONSOLE (SN610): ATTENDANT LISTED DIRECTORY NUMBER PROGRAMMING DESCRIPTION DATA Provide the system with diversion display. (1) 204 (2) 0: To be provided Specify the Incoming Call Identification (ICI) key to which each LDN call or Tie Line call from each trunk route will terminate.• YY = 15 (1) Trunk Route No. (00-63) (2) 00: C.O. Incoming Call 0 07: C.O. Incoming Call 7 40: Tie Line Incoming Call 0 47: Tie Line Incoming Call 7 Assign the ICI key, if required. • YY = 00 (1) ATTCON No. + + Key No. (2) F60XX *a: 00-07 (C.O. Incoming Call 0-7) 40-47 (Tie Line Incoming Call 0-7) Assign the indialed number to each LDN key or Tie Line key assigned by CM90. The indialed number should be different from any numbers assigned by CM10 and CM11. • YY = 01 (For DID) (1) 0 : Effective data in CM35 YY = 15 1-8 : LDN Key No. (00-07) assigned by CM90 (2) X-XXXX (Indialed No.) • YY = 02 (For Tie Line) (1) 0 : Effective data in CM35 YY=15 1-8 : Tie Line Key No. (00-07) as- signed by CM90 (2) X-XXXX (Indialed No.) END CM35 CM90 CM50 CM08 START , *a
CHAPTER 2 ND-45670 (E) Pag e 5 0 Revision 2.0 ATTENDANT CONSOLE (SN610): ATTENDANT LISTED DIRECTORY NUMBER To provide the LDN Diversion feature, the following programming is also required. DESCRIPTION DATA Provide the system with the LDN Diversion feature.(1) 205 (2) 0: To be provided Assign the data for LDN Diversion to each indialed No. assigned by CM50 YY = 01/02. Note:A call is diverted to LDN0-7/TIE0-7 keys as specified by CM58 YY = 02- 07, even if CM50 YY = 01/02, 1-8 has been set.• YY = 00 (Tenant No. of the LDN) (1) 00 : Effective data in CM35 YY = 15 01-08 : LDN Key No. (00-07) assigned by CM50 YY = 01 10 : Effective data in CM35 YY = 15 11-18 : Tie Line Key No. (00-07) as- signed by CM50 YY = 02 (2) Tenant No. (00-63) • YY = 01 (TAS Group No.) (1) Same as YY = 00 (2) TAS Group No. (00-63) • YY = 02 (Day Mode Destination of the LDN) (1) Same as YY = 00 (2) 00: LDN/TIE key 0 07: LDN/TIE key 7 08: To TAS 09: To the station assigned by CM58 YY = 08. • YY = 03 (Night Mode Destination) (1) Same as YY = 00 (2) 00: LDN/TIE key 0 07: LDN/TIE key 7 08: To TAS 09: To the station assigned by CM58 YY = 09. • YY = 04 (Day mode diversion for busy destination station) (1) Same as YY = 00 (2) 00: To ATTCON (BUSY key) 08: To TAS 09: Camped on CM08 CM58 START A
ND-45670 (E) CHAPTER 2 Page 51 Revision 2.0 ATTENDANT CONSOLE (SN610): ATTENDANT LISTED DIRECTORY NUMBER HARDWARE REQUIRED PN-AUCA card (DID Trunk) PN-2ODT (Tie Line Trunk) DESCRIPTION DATA • YY = 05 (Night mode diversion for busy destination station) (1) Same as YY = 00 (2) Same as YY = 04 • YY = 06 (Day mode diversion for non- answering destination station) (1) Same as YY = 00 (2) 00: To ATTCON (NANS key) 08: To TAS • YY = 07 (Night mode diversion for non- answering destination station) (1) Same as YY = 00 (2) Same as YY = 06 If a station is designated by YY = 02, 03, assign the station number to which the call is to be diverted. • YY = 08 (Day mode destination station) (1) Same as YY = 00 (2) X-XXXX (Station No.) • YY = 09 (Night mode destination sta- tion) (1) Same as YY = 00 (2) X-XXXX (Station No.) END A CM58
CHAPTER 2 ND-45670 (E) Pag e 5 2 Revision 2.0 ATTENDANT CONSOLE (SN610): ATTENDANT LOOP RELEASE PROGRAMMING To reenter the call that has been released from a loop before Automatic Recall (1200 Series Enhancement): DESCRIPTION DATA Provide the system with the Attendant Loop Release feature. (1) 014 : Attendant Loop Release (2) 0 : To be provided DESCRIPTION DATA Assign the access code for Call Pickup - Direct.• Y=0-3 (Numbering Plan Group 0-3) (1) X-XXX: Access Code (2) 021: Call Pickup - Direct END CM08 START START END CM20
ND-45670 (E) CHAPTER 2 Page 53 Revision 2.0 ATTENDANT CONSOLE (SN610): ATTENDANT PROGRAMMING PROGRAMMING DESCRIPTION DATA Assign the password code for Attendant Programming. • YY = 30 (1) 1 (2) XX-XX : Password Code (Max. 8 digits) X : 0-9, A (*), B(#) If no data is set, the default setting is NONE. In this case, the password is set to “12345678”. Assign the program (PROG) key for providing Attendant Programming on the SN610 ATTCON.• YY = 00 (1) ATTCON No. + + Key No. (2) F6111 Assign the access code for providing Attendant Programming for the SN610 ATTCON, if required.• Y = 0-3 (Numbering Plan Group 0-3) (1) X-XXX (Access Code) (2) A56 END CM60 START CM90 CM20 INITIAL ,