NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 2 60
Revision 2.0
INTERNAL ZONE PAGING WITH MEET-ME
To provide All Zone Internal Paging:
DESCRIPTION DATA
Provide the system with All Zone Internal 
Paging. (1) 158 
(2)  1 : Available
Assign the Class of Service for All Zone 
Internal Paging to the required stations.• CM12 YY = 02
(1)  X-XXXX: Station No. 
(2) XX
 XX
*a: Service Restriction Class (A) 
(00-15 ) 
•  CM15 YY = 49
(1)  00-15: Service Restriction Class (A) 
assigned by CM12 YY = 02 
(00-15 ) 
(2)  1 : Allowed
Assign an All Zone Internal Paging access 
code.•  Y = 0-3 (Numbering Plan Group 0-3) 
(1)  X-XXX: Access code (1-3 digits) 
(2)  A64: All Zone Internal Paging Access
Assign Group for Internal Zone Paging to the 
required Multiline Terminals.
Note:A maximum of 6 zones (0-5) internal
paging groups are available. Up to
16 Multiline Terminals can be
grouped per zone.•  YY = 05 (Paging Group Number) 
(1)  00-15 (Serial number in a Paging 
Group) 
(2)  X-XXXX (Primary Extension Number) 
Assign an All Zone Internal Paging function 
key to a line button on the desired Multiline 
Terminals.•  YY = 00 
(1)  X-XXXX (Primary Extension No.) +   
+ Key No. (01-16) 
(2)  F1278: All Zone Internal Paging
START
END
CM12
CM15
CM20
CM56
CM90
CM08
*a
, 
						

							ND-45670 (E) CHAPTER 2
Page 261
Revision 2.0
LAST NUMBER REDIAL
PROGRAMMING
To provide SN610 ATTCON with this feature (1200 Series Enhancement).
DESCRIPTION DATA
Provide the system with Last Number Redial. (1)  177
(2)  0: Available
Specify the capability for internal calls with 
this feature. If the data for CM08-178 is set to 
“0”, this feature will only be applied to 
outgoing calls.(1) 178
(2)  0/1 : Not available/Available
Assign the access code for Last Number 
Redial.•  Y = 0-3 (Numbering Plan Group 0-3)
(1)  X - XXX: Access Code (**)
(2) 069
Assign the Last Number Redial or Stack Dial 
feature access key to each Multiline Terminal, 
as required.
Refer to the Stack Dial feature for details on 
programming Stack Dial.•  YY = 00
(1)  Primary Extension No. +   +Key No. 
(2)  F0069: Last Number Redial 
F1000: Stack Dial 
DESCRIPTION DATA
Assign the Last Number Redial/Stack Dial 
key to each SN610 ATTCON.• YY=00
(1)  ATTCON No. + + Key No. 
(2)  F6121: Last Number Redial/Stack Dial
Refer to the Stack Dial feature for details on 
programming Stack Dial.
START
END
CM08
CM20
CM90,
END
CM90 START, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 62
Revision 2.0
LEAST COST ROUTING-3/6-DIGIT
PROGRAMMING 
DESCRIPTION DATA
Assign the access code for LCR Group 0-2.  •  Y = 0-3 (Number Plan Group 0-3)
(1) X-XXX (Access Code) 
(2)  A26: LCR Group 0
A27: LCR Group 1 
A28: LCR Group 2
Assign the Toll Restriction Patterns with five 
kinds of Trunk Restriction Classes assigned 
by CM12 YY = 01. 
Toll Restriction Patterns 00-15 are 
preassigned as shown below. 
If a new Restriction Pattern is required, 
change the data for Restriction Patterns 01-
13 (00, 14 and 15 are fixed). •  YY = 01-13 (Toll Restriction Pattern 
No. 01-13)
(1)  Trunk Restriction Class (1-5) 
(2) 0: Restricted 
3: Allowed
Assign an Area Code Development Pattern 
No. to each LCR Group, as needed. •  YYY = A00
(1)  0-2: (LCR Group 0-2) 
(2)  5-7: Area Code Development Pattern 
No. 5-7
Assign a Route Pattern No. to each area code 
for the Area Code Development Pattern No. 
assigned by YYY = A00. • YYY = 405-407 
(Area Code Development 
Pattern No. 5-7) 
(1)  NXX/1NXX (Area Code, Max. 8 digits)
(2)  000-063 (Route Pattern No. 00-63)CM20 START
CM81
CM8A
A
YYTRUNK
RESTRICTION
CLASS01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00
TOLL RESTRICTION PATTERN NUMBER ON EACH TRUNK RESTRICTION CLASS
1
2
3
4
5RCA
RCB
RCC
RCD
RCE3
3
3
3
30
0
0
0
03
3
3
0
03
3
0
0
03
0
0
0
00
0
0
0
00
0
0
0
00
0
0
0
03
3
3
0
03
3
0
0
03
0
0
0
03
0
0
0
03
0
0
0
00
0
0
0
03
3
3
3
30
0
0
0
0
0:
3:Restricted
Allowed 
						

							ND-45670 (E) CHAPTER 2
Page 263
Revision 2.0
LEAST COST ROUTING-3/6-DIGIT
DESCRIPTION DATA
Specify the order of LCR selection for the 
Route Pattern No. assigned by YYY = 405-
407.•  YYY = 000-063 (Route Pattern No. 
00-63)
(1)  1-4: Order of LCR Selection
1: 1st
2: 2nd
3: 3rd
4: 4th
(2) XXX
 XX
*a: 000-255 (LCR Pattern No. 000-255)
*b: 00-63 (Trunk Route No. 00-63)
For area code deletion, designate the digits to 
be deleted. •  YYY = 500-755 (LCR Pattern No. 
000-255) 
To delete all digits of the area code:
(1)  151 [Deletion of all digits of the area 
code (NXX, 1NXX) assigned by 
YYY = 405-407)] 
(2)  0: To be deleted 
To delete the designated digit of an area 
code: 
•  YYY = 500-755
(1)  153 (Designation of digit to be deleted)
(2)  00: No digits deleted 
01: First digit deleted 
10: First 10 digits deleted 
CCC: No digits deleted
For area code addition, designate the digits to 
be added. •  YYY = 500-755
(1)  100 (Designation of digit Addition Pat-
tern No.) 
(2)  00-49 (Digit Addition Pattern No. 00-
49) 
CCC: No digit addition 
•  YYY = 900-949 (Digit Addition Pattern 
No. 00-49)
(1) 0 
(2)  X-X...X [Digits to be added (Max. 32 
digits.)] 
X = 0-9, A(*), B(#), C(Fixed Pause) 
CM8A
B
A
*b *a
|| 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 64
Revision 2.0
LEAST COST ROUTING-3/6-DIGIT
DESCRIPTION DATA
If three-digit Toll Restriction is provided, 
assign the Toll Restriction Pattern No. to the 
LCR Pattern No.
If six-digit Toll Restriction is provided, assign 
the following data to the LCR Pattern No. and 
set up the six-digit Toll Restriction Pattern 
Ta b l e s .
(1) Specify the Trunk Restriction Classes to 
which 6-digit Toll Restriction applies.
Example:
 412
 - 211
Area Code Office Code
RCA: No restrictions (three-digit TR)
RDB: 412-211 is allowed (six-digit TR)
RCC: 412-211 is allowed (six-digit TR)
RCD: 412 is restricted (three-digit TR)
RCE: 412 is restricted (three-digit TR)•  YYY = 500-755 (LCR Pattern No. 
000-255) 
(1) 000 
(2)  00-15 (Toll Restriction Pattern No. 
specified by CM81)
•  YYY = 500-755 (LCR Pattern No. 
000-255) 
(1)  021-028 (Trunk Restriction Class as-
signed by CM12 YY = 0.)
021: Unrestricted (RCA) 
022: Non-Restricted 1 (RCB) 
023: Non-Restricted 2 (RCC) 
024: Semi-Restricted 1 (RCD)
025: Semi-Restricted 2 (RCE)
026: Restricted 1 (RCF) 
027: Restricted 2 (RCG) 
028: Fully-Restricted 2 (RCH) 
(2)  0 : 6-digit Toll Restriction Pattern
1 : 3-digit Toll Restriction Pattern 
as per 1st Data = 000
(2) Assign the six-digit Toll Restriction Pat-
tern No. to the LCR Pattern No. • YYY = 500-755 
(1) 020 
(2)  00-49 (6-digit Toll Restriction Pattern 
No. 00-49) 
(3) Assign the Office code (three-digits) and 
the availability to access the office code 
to the six-digit Toll Restriction Pattern 
No. assigned by (2). •  YYY = 800-849 (6-digit Toll Restric-
tion Pattern No. 00-49) 
(1)  XXX (3 digits of Office Code) 
(2) 0/1 : Restricted/Allowed
CM8A
C
B
021
022
023
024
025500 1
0
0
1
1 CM8A
TRUNK REST CLASS DATA YYY 
						

							ND-45670 (E) CHAPTER 2
Page 265
Revision 2.0
LEAST COST ROUTING-3/6-DIGIT
DESCRIPTION DATA
If the Prefix is to be added, assign the 
following data to the LCR Pattern No.
(1) Assign the 6-digit Prefix Pattern No. to 
the LCR Pattern No. •  YYY = 500-755 (LCR Pattern No. 
000-255) 
(1) 150 
(2) 00:  6-digit Prefix Pattern No. 00 
49: 6-digit Prefix Pattern No. 49
50:  Prefix is to be added regardless 
of Office Code.
CCC: No Prefix
(2) Assign the office code (three digits), re-
quiring the Prefix, to the six-digit Prefix 
Pattern No. •  YYY = 800-849
(1)  XXX (3-digit of Office Code)
(2)  1 : Allowed
Specify the maximum number of digits to be 
dialed by the calling party. •  Y = 5-7 (Area Code Development 
Pattern No. 5-7 assigned by 
CM8A, YYY = A00)
The maximum number of digits including the 
area codes should be assigned to each area 
code. (1)  X-X...X (Area Code dialed, Max. 8 dig-
its) 
(2) 01 : 1 digit 
24 : 24 digits 
79 : 79 digits 
Provide the Toll Restriction feature to the 
required trunk routes.•  YY = 11
(1)  Trunk Route No. (00-63) (00) 
(2)  0: To be provided
Specify route access capability for each 
restriction class. •  YY = 51-55 
(1)  Trunk Route No. (00-63)
(2) 0/1 : Restricted/Allowed 
Assign the Area Code Development Pattern 
No. for Toll Restriction and Maximum Digit 
Analysis to each trunk. •  YY = 76
(1)  Trunk Route No. (00-63)
(2)  05-07 [Area Code Development Pattern 
(No. 5-7)]CM8A
C
END
CM85
CM35 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 66
Revision 2.0
LEAST COST ROUTING-3/6-DIGIT
To provide L.C.R. with Time of Day Routing, add the following system data programming.
DESCRIPTION DATA
Assign the Date Pattern No. to each area code 
for the Area Code Development Pattern No. 
assigned by YYY = A00.•  YYY = 405-407(Area Code Develop-
ment Pattern No. 5-7) 
(1)  X-X...X (Area Code Max. 8 digits)
(2)  300-303 (Date Pattern No. 0-3) 
Assign the Time Pattern No. to each day of 
the week for the Date Pattern No. assigned by 
YYY = 405-407. •  YYY = 300-303 (Date Pattern No. 0-3) 
(1) 0: SUN
1: MON 
2: TUE 
3: WED 
4: THU 
5: FRI 
6: SAT 
(2)  200-207 (Time Pattern No. 00-07) CM8A
A START 
						

							ND-45670 (E) CHAPTER 2
Page 267
Revision 2.0
LEAST COST ROUTING-3/6-DIGIT
DESCRIPTION DATA
Assign the Route Pattern No. to the required 
time of day for the Time Pattern No. assigned 
by YYY = 300-303.•  YYY = 200-207 (Time Pattern No. 00-
07) 
(1) XX
 XX (Time)
*a: Hours (00-23) 
*b: Minutes (00/30) 
To define the following Time Pattern: 
If the Tenant Pattern No. is assigned by YYY 
= 200-207, assign the Route Pattern No. to 
the required Tenant No. for the Tenant 
Pattern No.(2)  000-063 (Route Pattern No. 00-63) 
If Tenant Pattern is required, set 100-115
(Tenant Pattern No. 00-15) 
•  YYY = 100-115 (Tenant Pattern No. 
00-15) 
(1)  00-63 (Tenant No. 00-63) 
(2)  000-063 (Route Pattern No. 00-63)
CM8A
A
END
*b *a
0000
0030
0100
0130
0200
0730
2000
2030
2330
0800
0830
1930
YYY TIME (1) ROUTE PATTERN (2)
200 (Time Pattern No. 00)
200 (Time Pattern No. 00)12:00 PM-8:00 AM
8:00 PM-12:00 PM
8:00 PM-8:00 PM000 (Route Pattern No. 00)
001 (Route Pattern No. 01) 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 68
Revision 2.0
LEAST COST ROUTING-3/6-DIGIT
To provide C.O. operator call with LCR, assign the following system data.
DESCRIPTION DATA
Assign the access code for LCR Group 0.  •  Y = 0-3 (Number Plan Group 0-3) 
(1) X-XXX (Access Code) 
(2)  A26: LCR Group 0 
Assign the Toll Restriction Patterns with five 
kinds of Trunk Restriction Classes assigned 
by CM12 YY = 01. Toll Restriction Pattern 
00-15 is already programmed as shown 
below. If a new Restriction Pattern is 
required, change the data of the Restriction 
Pattern 01-13 (00, 14 and 15 are fixed).•  YY = 01-13 (Toll Restriction Pattern 
No. 01-13) 
(1)  Trunk Restriction Class (1-5) 
(2) 0: Restricted 
3: Allowed 
Assign the Route Pattern No. to each area 
code for the Area Code Development Pattern 
No. assigned by YYY = A00.•  YYY  = 410 (Area Code for C.O. Oper-
ator) 
(1)  X-XXX (Area Code for C.O. Operator). 
This data is only effective for an access 
code assigned to CM20-A26.
(2)  000-063 (Route Pattern No. 00-63)CM20
A START
CM81
CM8A
YYTRUNK
RESTRICTION
CLASS01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00
TOLL RESTRICTION PATTERN NUMBER ON EACH TRUNK RESTRICTION CLASS
1
2
3
4
5RCA
RCB
RCC
RCD
RCE3
3
3
3
30
0
0
0
03
3
3
0
03
3
0
0
03
0
0
0
00
0
0
0
00
0
0
0
00
0
0
0
03
3
3
0
03
3
0
0
03
0
0
0
03
0
0
0
03
0
0
0
00
0
0
0
03
3
3
3
30
0
0
0
0
0:
3:Restricted
Allowed 
						

							ND-45670 (E) CHAPTER 2
Page 269
Revision 2.0
LEAST COST ROUTING-3/6-DIGIT
Figure 2-1  LCR Development Sequence DESCRIPTION DATA
Assign the 1st order of LCR selection for the 
Route Pattern No. assigned by YYY = 410.•  YYY = 000-063 (Route Pattern No. 00-
63) 
(1)  1: 1st order of LCR selection 
(2) XXX
 XX 
*a: 000-255 (LCR Pattern No. 000-255)
*b: 00-63 (Trunk Route No. 00-63) 
Assign the Toll Restriction Pattern No. to the 
LCR Pattern No. assigned by YYY = 410. •  YYY = 500-755 (LCR Pattern No. 
000-255)
(1) 000 
(2)  00-13, 15 (Toll Restriction Pattern No. 
specified by CM81)
A
END
CM8A
*b *a
CM8A
LCR
ACCESS
CODEA00
AREA CODE405
 407
200 207
300 303
100 115
000 063
500 575TIME PATTERN
DATE PATTERNTENANT PATTERN
AREA CODE
DEVELOPMENT PATTERN
ROUTE PATTERNLCR PATTERN
DIGIT ADDITION
TRUNK ROUTE SELECTIONTRUNK RESTRICTION
PATTERN 00 -15
DIGIT DELETION
DIGIT 
ADDITION 900
 949
1ST
2ND
3RD
4TH