Home > NEC > Communications System > NEC Neax2000 Ivs Feature Programming Manual

NEC Neax2000 Ivs Feature Programming Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax2000 Ivs Feature Programming Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 479
    Add page 201 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 ND-45670 (E)
Pag e 1 84
Revision 2.0
CUSTOMER ADMINISTRATION TERMINAL (CAT)
PROGRAMMING
DESCRIPTION DATA
Assign the class of service for CAT to the 
required Multiline Terminals.• CM12 YY = 02 
(1) X-XXXX (Primary Extension No.)
(2) XX XX
 
*a: Service Restriction Class (B) 
(00-15 )
• CM15 YY = 56 
(1) XX: [Service Restriction Class (B) 
(00-15)] assigned by CM12 YY 
= 02.
(2) 1  Allowed
Specify the command codes accessible to 
each Password Level.• YY = 00: Password Level 0-6
• YY = 01: Password Level 1-6
• YY = 02: Password Level 2-6
• YY = 03: Password Level 3-6
• YY = 04: Password Level 4-6
• YY = 05: Password Level 5-6
• YY = 06: Password Level 6
• YY = 10: Password Level 0
• YY = 11: Password Level 1
• YY = 12: Password Level 2
• YY = 13: Password Level 3
• YY = 14: Password Level 4
• YY = 15: Password Level 5
• YY = 16: Password Level 6
(1) XX
*a: 00-FF (Command Codes exclu-
sive of 03, E7, E9) 
(2) 0/1  Allowed/Restricted 
A
CM12
CM15
CME7 START
*a
*a
    Add page 202 to Favourites
    image text
    Enable zoom 
    							ND-45670 (E) CHAPTER 2
Page 185
Revision 2.0
CUSTOMER ADMINISTRATION TERMINAL (CAT)
Note 1:If the system data all clear or system data partial clear is required before programming from a CAT, per-
form the following operations:
1. Plug the PN-2DLCB/4DLCA card into LT00 Slot of PIM0 
2. Connect the CAT to LEN0000 at the MDF
3. Set SW3 on the MP card to “B”
4. Press SW1 (RESET Switch) on the MP card (System Data All Clear/Partial Clear)
5. Set SW3 to “0” and press SW1.
6. Set the Multiline Terminal to CAT mode (Station Number 300 is automatically assigned to the Multi-
line Terminal). 
Note 2:If Password Service is activated, enter the predetermined password by CM03 before programming from a
CAT. 
 + 03 +   + Password Level No. (0-7)+   +Password+  
- “OK” will be displayed, if accepted.
- “DATA ERROR” will be displayed if the password is incorrect.
DESCRIPTION DATA
Enable the system to change the password.  (1) 8 
(2) 0
: Allowed
Assign a password to each Password Level.  (1) 0-7 (Password Level 0-7)
(2) X-X...X (Max. 8 digits Password Code)
A password code for Password Level 7
must be assigned prior to providing the
password service by Function No. 9 of
CME9. 
The following passwords are not available.
“CCCCCCCC”
“FFFFFFFF”
Provide the system with Password service. 
After setting this data, access to system 
programming will be available with 
password entry only.(1) 9 
(2) 0: Provided 
END
A
CME9
STDEDEEXE
    Add page 203 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 ND-45670 (E)
Pag e 1 86
Revision 2.0
DATA LINE SECURITY
PROGRAMMING
DESCRIPTION DATA
Assign the function of Analog Data Station 
(Single-Line Station with FAX or MODEM) 
to the required stations.• YY = 07
(1) X-XXXX (Station No.)
(2) 0: Data Station 
END
CM13 START
    Add page 204 to Favourites
    image text
    Enable zoom 
    							ND-45670 (E) CHAPTER 2
Page 187
Revision 2.0
DELAYED RINGING
PROGRAMMING
DESCRIPTION DATA
Assign the Delayed Ringing feature to each 
line key on a Multiline Terminal.
Note:The Delayed Ringing feature can be
assigned to the first 16 line/trunk
keys (Key 01-16). • YY = 03
(1) Primary Extension No. +     + Key No.
Note
(2) 0: Delayed Ringing 
Specify the timing for Delayed Ringing.  • Y = 1
(1) 09
(2) 01-20: 2-40 sec. in 2 sec. increments
If no data is set, the default setting is 10
seconds.
END
CM90 START
CM41,
    Add page 205 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 ND-45670 (E)
Pag e 1 88
Revision 2.0
DIAGNOSTICS
PROGRAMMING
Refer to the Maintenance Manual.
    Add page 206 to Favourites
    image text
    Enable zoom 
    							ND-45670 (E) CHAPTER 2
Page 189
Revision 2.0
DIAL CONVERSION
PROGRAMMING
DESCRIPTION DATA
Assign the Card Number of the DTMF 
Receiver to the required LENs.
Note:When using the internal DTMF Re-
ceiver on the PN-CP03 card, assign
the Card No. E200 to LEN No.
0124.(1) LEN (0000-0511)
(2) Card No. of DTMF Receiver
E200-E203: For PIM0/1 
E204-E207: For PIM2/3 
E208-E211: For PIM4/5 
E212-E215: For PIM6/7 
Assign the type of telephone set (DTMF) to 
DTMF Stations. This data assignment is not 
required for Multiline Terminal stations. • YY = 00
(1) X-XXXX (Station No.)
(2) 3: DTMF Telephone set 
Assign DTMF Receivers for use with DTMF 
Stations. • Y = 0 (Make Busy)
(1) XX
 X 
Card No. 00-15 assigned by 
CM10 (E200-E215)
Circuit No. 0-3
(1) 1: Make Busy Cancel 
• Y = 1 (PBR for incoming call from Tie 
Line/DID)
(1) XXX (Ditto to Y = 0)
(2) 1:For both DTMF station and Tie 
Line/DID
A
CM10
CM12
CM45 START
INITIAL
    Add page 207 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 ND-45670 (E)
Pag e 1 90
Revision 2.0
DIAL CONVERSION
DESCRIPTION DATA
For a DP trunk, assign the type of signaling 
for Outgoing and Bothway trunk routes to 
DP. 
Specify the DP Sender characteristics to 
match the Central Office.• YY = 01
(1) Trunk Route No. (00-63) 
(2) 2 
• YY = 23 (DP Sender Inter Digital 
Pause) 
(1) Trunk Route No. (00-63) 
(2) 0: 300 ms 
1: 400 ms 
2: 500 ms 
3: 600 ms 
4: 700 ms 
5: 900 ms 
6: 1100 ms 
7: 800 ms 
• YY = 25 (DP Sender Make Ratio) 
(1) Trunk Route No. (00-63) 
(2) 0/1: 33%/39%
• YY = 45 (DP Sender Release Timing) 
(1) Trunk Route No. (00-63)
(2) 0: 2 sec. 
1: 4 sec. 
2: 6 sec. 
3: 8 sec. 
4: 12 sec. 
5: 14 sec. 
6: 16 sec. 
7: 10 sec. 
For a DTMF trunk, assign the type of 
signaling for Outgoing and Bothway Trunk 
Routes to DTMF. • YY = 01
(1) Trunk Route No. (00-63) 
(2) 7
B
A
CM35
    Add page 208 to Favourites
    image text
    Enable zoom 
    							ND-45670 (E) CHAPTER 2
Page 191
Revision 2.0
DIAL CONVERSION
HARDWARE REQUIRED 
DTMF Receiver (PN-8RST) ´ n 
n: Depends on the number of DTMF stations and the traffic condition of the system.
DESCRIPTION DATA
Specify the DTMF Sender characteristics to 
match the Central Office.• YY = 24 (DTMF Inter Digital Pause) 
(1) Trunk Route No. (00-63)
(2) 0: 32 ms 
1: 64 ms 
2: 80 ms 
3: 96 ms 
4: 160 ms 
5: 192 ms 
6: 240 ms 
7: 128 ms
• YY = 26 (DTMF Sender Signal Width) 
(1) Trunk Route No. (00-63)
(2) 0/1: 64 ms/128 ms 
• YY = 46 (DTMF Sender Release Tim-
ing) 
(1) Trunk Route No. (00-63) 
(2) 0: 2 sec. 
1: 4 sec. 
2: 6 sec. 
3: 8 sec. 
4: 12 sec. 
5: 14 sec. 
6: 16 sec. 
7: 10 sec. 
Assign whether “*” or “#” from a DTMF 
Telephone is used as a Switch Hook Flash 
while hearing Busy Tone. (1) 050 (* is used as Switch Hook Flash) 
(2) 0: Effective
(1) 051 (# is used as Switch Hook Flash) 
(2) 0: Effective
END
B
CM08
    Add page 209 to Favourites
    image text
    Enable zoom 
    							CHAPTER 2 ND-45670 (E)
Pag e 1 92
Revision 2.0
DIRECT DIGITAL INTERFACE
PROGRAMMING
Refer to the DDI System Manual. 
HARDWARE REQUIRED 
Refer to the DDI System Manual.
    Add page 210 to Favourites
    image text
    Enable zoom 
    							ND-45670 (E) CHAPTER 2
Page 193
Revision 2.0
DIRECT INWARD DIALING (DID)
PROGRAMMING
DESCRIPTION DATA
Assign the ring rate on a DID call.  (1) 180
(2) 0/1: 0.2 sec. ON, 0.2 sec. OFF, 0.2 
sec. ON, 0.2 sec. OFF, 0.2 sec. 
ON, 0.2 sec. OFF/As per the data 
of CM35 YY = 33
Assign the Trunk Numbers to the required 
LENs.(1) LEN (0000-0511) 
(2) Trunk No. (D000-D255)
Assign the data for DID to the Trunk 
Numbers assigned by CM10.• YY = 00 (Trunk Route Allocation)
(1) Trunk No. (000-255)
(2) Trunk Route No. (00-63) (03) 
• YY = 01 (Tenant Allocation)
(1) Trunk No. (000-255)
(2) Tenant No. (00-63) (00)
• YY = 02 (Terminating System in Day 
Mode) 
• YY = 03 (Terminating System in Night 
Mode) 
(1) Trunk No. (000-255)
(2) 31CM08
CM10
CM30 START
A
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax2000 Ivs Feature Programming Manual