NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 4 12
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
To provide the LEDs on the Multiline Terminal for UCD Call Waiting Indication:
DESCRIPTION DATA
Assign the incoming call to queuing mode 
when all UCD stations are busy.(1) 212
(2) 1 : Queuing
Specify the maximum number of queuing in 
each UCD group for controlling call waiting 
lamp of a Multiline Terminal.
Note:Depending on the number of queuing
station/trunk, lamp indication pat-
tern on a Multiline Terminal is differ-
ent as shown below:(1) 15
(2) 01-99 (Number of queuing in each UCD 
group)
If no data is set, the default setting is 01.
N=Number of queuing station/trunk 
Assign the Call Waiting Indication LED to the 
required Multiline Terminal.• YY = 00
(1) Primary Extension No. +     + Key No.
(2) F1280: UCD Group 00 
F1295: UCD Group 15
END
CM08 START
CM42
CM90
CONDITIONS LAMP INDICATION
2nd Data=01 Steady on red irrespective of number of queuing station/trunk
1 
£N < 2nd Data (2nd Data 
¹ 01) Steady on red
2nd Data 
£ N (2nd Data 
¹ 01) Flashing red
,
|| 
						

							ND-45670 (E) CHAPTER 2
Page 413
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
To provide an external indicator for UCD Call Waiting:
DESCRIPTION DATA
Assign the incoming call to queuing mode 
when all UCD stations are busy.(1) 212
(2) 1 : Queuing
Specify the maximum number of queuing in 
each UCD group for controlling external 
equipment Interface.(1) 15
(2) 01-99 (Number of queuing in each UCD 
group)
If no data is set, the default setting is 01.
Note:Depending on the number of queuing
station/trunk, lamp indication pat-
tern on an external equipment is dif-
ferent as shown below:
N=Number of queuing station/trunk 
Assign the PN-DK00 card to the required 
LEN.(1) LEN (0000-0511)
(2) E800-E831 (PN-DK00 Card No.)
E800-E807: For PIM0/1
E808-E815: For PIM2/3
E816-E823: For PIM4/5
E824-E831: For PIM6/7
Assign the function of UCD Call Waiting In-
dication to the PN-DK00.(1)
XX X 
*a *b 
*a: Card No. (00-31) assigned by CM10
E800-E831. 
*b: Circuit No. (0-3)
(2) 14XX
 
*a 
*a: UCD Group No. (00-15) assigned by
CM17.
START
CM08
CM42
CM10
CM44
A
CONDITIONS LAMP INDICATION
2nd Data = 01 Lamp on irrespective of number of queuing station/trunk (For the 
indication pattern, see CM59.)
N < 2nd Data (2nd Data 
¹ 01) Lamp off
2nd Data 
£N (2nd Data 
¹ 01) Lamp on (For the indication pattern, see CM59.) 
						

							CHAPTER 2 ND-45670 (E)
Pag e 4 14
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
To provide the priority queuing for incoming trunk calls:
DESCRIPTION DATA
Specify the UCD Call Waiting Indicator indi-
cation pattern.(1) 00
(2) 01 : 30 IPM (1 sec. ON/OFF)
02: 60 IPM (0.5 sec. ON/OFF)
03: 120 IPM (0.25 sec. ON/OFF)
07: Steadily On
DESCRIPTION DATA
Assign Priority Queuing per trunk route. • YY=60
(1) Trunk Route No. (00-63)
(2) 0/1 : To be provided/Not to be 
provided
Assign Digit Conversion on DID call, if re-
quired.• YY=18
(1) Trunk Route No. (00-63)
(2) 0/1 : To be provided/Not to be 
provided
Assign Priority Queuing per DID incoming 
LDN, if Digit Conversion is provided (CM35 
YY=18 is set to 0).•Y=6
(1) X-XXXX: Station Number received
(2) 0/1 : Not to be provided/To be 
provided
END
A
CM59
START
END
CM35
CM76 
						

							ND-45670 (E) CHAPTER 2
Page 415
Revision 2.0
UNIFORM CALL DISTRIBUTION (UCD) WITH OVERFLOW
HARDWARE REQUIRED 
To provide the delay announcement for UCD: 
- PN-2DATA card
To provide the LEDs on the Multiline Terminal:
-ETJ-8-1/ETJ-16DC-1/ETJ-16DD-1/ETJ-24DS-1 and PN-2DLCB/PN-4DLCA card 
To provide the Indicator for UCD Call Waiting: 
- PN-DK00 card 
- External Indicator provided by the customer Requirement for External Indicator 
Control Method: Ground/Battery (Max.125 mA) 
Type: Visual and/or Audible type with volume control 
Make the following connections at the MDF according to the type of the indicator. For details, refer to the MDF
cross connection for an External Indicator (TAS Indicator) in the INSTALLATION PROCEDURE MANUAL.
PBX
PN-DK00 CARD
PZ-PW86 CARD
G
PBX
PN-DK00 CARDMDF
MDFEXTERNAL INDICATOR
WITH BATTERY
EXTERNAL INDICATOR WITH
BATTERY (GROUND START)IND
IND
G 
						

							CHAPTER 2 ND-45670 (E)
Pag e 4 16
Revision 2.0
UNIFORM NUMBERING-VOICE & DATA
PROGRAMMING
For an open numbering system: 
DESCRIPTION DATA
Assign an access code for LCR Group 0-3. • Y = 0-3 (Numbering Group 0-3)
(1) X-XXX (Access Code) 
(2) A26: LCR Group 0
A27: LCR Group 1 
A28: LCR Group 2 
A29: LCR Group 3 
Assign an Area Code Development Pattern 
No. to each LCR Group. • YYY = A00
(1) 0-3: LCR Group 0-3 
(2) 5-7: Area Code Development Pattern 
No. 5-7 
Assign a Route Pattern No. to each area code 
for the Area Code Development Pattern No. 
assigned by CM8A YYY = A00.• YYY = 405-407 (Area Code Develop-
ment Pattern No. 5-7) 
(1) NXX/1NXX (Area Code, Max. 8 digits) 
(2) 000-063 (Route Pattern No. 00-63) 
Assign an area code for Intra-Office Termina-
tions, if required. • YYY = 405-407 (Area Code Develop-
ment Pattern No. 5-7) 
(1) X-XXXXX (Area Code, 1-5 digits) 
(2) 800 (Intra-Office Termination)
801 (1-digit intra-office station) 
802 (2-digit intra-office station) 
803 (3-digit intra-office station)
804 (4-digit intra-office station) 
805 (5-digit intra-office station)
Specify the order of LCR selection for the 
Route Pattern No. assigned by YYY = 405-
407. • YYY = 000-063
(Route Pattern No. 00-63) 
(1) 1-4: Order of LCR Selection 
1: 1st
2: 2nd
3: 3rd
4: 4th
(2) XXX
 XX 
*a: 000-255 (LCR Pattern No. 000-255)
*b: 00-63 (Trunk Route No. 00-63) 
CM20 START
CM8A
A
*b *a 
						

							ND-45670 (E) CHAPTER 2
Page 417
Revision 2.0
UNIFORM NUMBERING-VOICE & DATA
DESCRIPTION DATA
Assign the digits to be deleted from calls to 
distant offices. To delete all digits of an area 
code: • YYY = 500-755 (LCR Pattern No. 000-
255)
(1) 151 [Deletion of all digits of area code 
(NXX, 1NXX)] assigned by YYY 
= 405-407)
(2) 0: To be deleted
To delete the designated digit of an area code:  • YYY = 500-755
(1) 153 (Designation of digit to be deleted)
(2) 00: No digits deleted 
01: First digit deleted
10: First 10 digits deleted
CCC: No digits deleted
Assign the digits to be added to the digits sent 
to the distant office. • YYY = 500-755
(1) 100 (Designation of digit Addition Pat-
tern No.) 
(2) 00-49 (Digit Addition Pattern No. 00-49) 
CCC: No digits added 
• YYY = 900-949 (Digit Addition Pattern 
No. 00-49) 
(1) 0 
(2) X-X...X [Digits to be added (Max. 32 
digits)] 
X = 0-9, A (*), B (#), C (Fixed Pause)
Assign the digits to be added to the required 
trunk routes when adding digits to those re-
ceived from a distant office.• YY = 17 
(1) 00-63 (Trunk Route No.) 
(2) 00: Add 0
01: Add 1
02: Add 2
03: Add 3
04: Add 4
05: Add 5
06: Add 6
07: Add 7
08: Add 8
09: Add 9
10: Add 2 digits per CM50
CM35
CM8A
A
B
|| 
						

							CHAPTER 2 ND-45670 (E)
Pag e 4 18
Revision 2.0
UNIFORM NUMBERING-VOICE & DATA
Example 1:
 When the PBX is an end office in a network employing an Open Numbering System, office A requires 
all the digits dialed on an incoming call from the PBX.
DESCRIPTION DATA
Assign the data for digit deletion to the re-
quired trunk routes for deleting the first one or 
two digits received from a distant office.• YY = 17
(1) 00-63 (Trunk Route No.) 
(2) 11: Delete first digit
12: Delete first two digits
If two digits are to be added, assign the digits 
to be added (See CM35 YY = 17, 2nd data = 
10).• YY = 00
(1) 0 
(2) XX (Digits to be added) 
CM50
CM35
B
END
22-200
OFFICE
B
OFFICE
C OFFICE
A 21-200
200
8XX-XXXX8XX-XXXX
23-200
PBX
Trunk Route : 0
Tie Line Access Code : 8
Area Code of Office A : 21
Area Code of Office B : 22
Area Code of Office C : 23
Numbering Plan Group : 0 
						

							ND-45670 (E) CHAPTER 2
Page 419
Revision 2.0
UNIFORM NUMBERING-VOICE & DATA
Programming for Example 1:
Example 2:
When the PBX is a Tandem Office in the network.
COMMAND CODE 1ST DATA 2ND DATA REMARKS
20 Y= 0 8 A26 Assignment of Access Code 8 of LCR
Group 0. 
8A YYY = A00
8A YYY = 405 
8A YYY = 405 
8A YYY = 405 
8A YYY = 0000
21
22
23
15
000
000
000
00000Assignment of Area Code Development
Pattern No. 5.
Assignment of Route Pattern 
No. 00 to Area Codes 21, 22, and 23.
Assignment of the order of LCR selec-
tion (1st) for Route Pattern No. assigned
by YY Y = 405. 
8A YYY = 500  100 00 Assignment of Digit Addition Pattern
No. 00.
8A YYY = 900 0 8 Assignment of the digital code to be add-
ed for each area code.
OFFICE
B OFFICE
A
XXXX
PBX
DI AL NO.
821-XXXX
/8838-XXX
TRUNK ROUTE 01  21-XXXX
/838-XXX
821-XXXX XXX
838-XXX
Trunk Route to Office B: 01
Tie Line Access Code : 8
Area Code of Office B : 21
Intra-Office Termination: 838 (1400 IMS) 
						

							CHAPTER 2 ND-45670 (E)
Pag e 4 20
Revision 2.0
UNIFORM NUMBERING-VOICE & DATA
Programming for Example 2:
COMMAND CODE 1ST DATA 2ND DATA REMARKS
20 Y = 08A26Assignment of Access Code 8 of LCR Group
0.
8A YYY = A00 0 5Assignment of Area Code Development Pat-
tern No. 5.
8A YYY = 405 21 000Assignment of Route Pattern No. 01 to Area
Code 21 of office B. 
8A YYY = 405 838 800Assignment of Intra-Office Termination to
the office code 838.
8A YYY = 000 1 00001Assignment of the order of LCR selection
(1st) for Route Pattern No. assigned by YYY
= 405.  
						

							ND-45670 (E) CHAPTER 2
Page 421
Revision 2.0
UNIFORM NUMBERING-VOICE & DATA
• For Closed Numbering System 
DESCRIPTION DATA
Assign an access code for LCR Group 3.  • YY = 0-3 (Numbering Group 0-3) 
(1) X-XXX (Access Code)
(2) A29: LCR Group 3 
Assign an Area Code Development Pattern 
No. to LCR Group 3. • YYY = A00
(1) 3: LCR Group 3 
(2) 5-7: Area Code Development Pattern 
No. 5-7 
Assign a Route Pattern No. to each area code 
for the Area Code Development Pattern No. 
assigned by CM8A YYY = A00.• YYY = 405-407 (Area Code Develop-
ment Pattern No. 5-7)
(1) NXX/1NXX (Area Code, max. 8 digits) 
(2) 000-063 (Route Pattern No. 00-63) 
Assign an area code (station number) for In-
tra-Office Terminations, if required.• YYY = 405-407 (Area Code Develop-
ment Pattern No. 5-7) 
(1) X-XXXXX (Area Code, max. 5 digits)
(2) 801: l-digit Intra-Office Station 
805: 5-digit Intra-Office Station
Specify the order of LCR selection for the 
Route Pattern No. assigned by YYY = 405-
407. • YYY = 000-063 (Route Pattern No. 00-
63)
(1) 1-4: Order of LCR Selection
1: 1st
2: 2nd
3: 3rd
4: 4th
(2) XXX
 XX 
*a: 000-255 (LCR Pattern No. 000-255)
*b: 00-63 (Trunk Route No. 00-63) 
Assign the digits to be deleted when deleting 
digits of an area code sent to a distant office. 
To delete all digits of an area code: • YYY = 500-755 (LCR Pattern No. 000-
255) 
(1) 151 [Deletion of all digits of area code 
(NXX, 1NXX)] assigned by YYY 
= 405-407)
(2) 0: To be deleted 
A START
CM8A
CM20
||
*b *a