NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Page 243-1 Addendum-001
Revision 2.1 JULY, 1998
GROUP CALL: AUTOMATIC CONFERENCE (6/10 PARTY) DATA ASSIGNMENT
To provide the Group Call-Automatic Conferrence (6/10 Party):
DESCRIPTION DATA
Assign a Conference Trunk Card Number to 
the required LEN.(1)
(2)LEN (0000-0511)
ED00-ED03: Conference Trunk Card No.
Assign the stations which belongs to each pag-
ing group, and their number within the group. 
A maximum of 9 stations can be paged simul-
taneously except the conference leader.
Note 1:Single line telephones, Multline
Terminals and PS can be as-
signed as the station within the
group.
A virtual-line cannot be as-
signed.
Note 2:A station can belong to multiple
groups.•
(1)
(2)YY=00-07: Simultaneous Paging Group 0-
7
00-15: Serial No. within the Group
X-XXXX: Station No.
Assign a Service Restriction Class to each sta-
tion.•
(1)
(2)YY=02
X-XXXX: Station No.
XX
 XX
00-15: Service Restriction 
Class A
Allow the Service Restriction Class A to page 
the group.•
(1)
(2)YYY=119
00-15: Service Restriction Class A assigned 
by CM12 YY=02
0: Allowed
Assign the access code of paging groups for 
Group Call-Automatic Conference (6/10 Par-
ty).
Note:Even if an extension does not be-
long to the conference group, the
extension can page the confer-
ence group, and can re-partici-
pate in the conference if there is
an idle circuit on the Conference
Trunk.•
(1)
(2)Y=0-3 (Tenant Group No.)
X-XX: Access Code
B00: Simultaneous Paging Group 0
B07: Simultaneous Paging Group 7
B10: Re-participation Group 0
B17: Re-participation Group 7
START
CM56
CM12
CM20
CM15
A
CM10
INITIAL
~ ~
~ ~ 
						

							ND-45670 (E) CHAPTER 2
Addendum-001 Page 243-2
JULY, 1998 Revision 2.1
DESCRIPTION DATA
Assign a Group Call-Automatic Conference 
(6/10 Party) key of each paging group to the 
Multiline Terminal, if required.
Note:Even if an extension does not be-
long to the conference group, the
extension can page the confer-
ence group, and can re-partici-
pate in the conference if there is
an idle circuit on the Conference
Trunk.•
(1)
(2)Y=00
X-XXXX: Primary Extension No. +  
+key No.
F0B00: Simultaneous Paging Group 0
F0B07: Simultaneous Paging Group 7
F0B10: Re-participation Group 0
F0B17: Re-participation Group 7
Specify the duration of simultaneous paging. •
(1)
(2)Y=0
95
01-99: 4-396 sec. in 4 sec. increments
If no data is set, the default setting is 32-36 
seconds.
CM41
A
END
CM90,
~ ~
~ ~ 
						

							CHAPTER 2 ND-45670 (E)
Page 243-3 Addendum-001
Revision 2.1 JULY, 1998
GROUP CALL: 2-WAY CALLING
To provide the Group Call-2 Way Calling:
DESCRIPTION DATA
Assign the stations which belongs to each pag-
ing group, and their number within the group. 
A maximum of 9 stations can be paged simul-
taneously except the conference leader.
Note 1:Single line telephones, Multline
Terminals and PS can be as-
signed as the station within the
group.
A virtual-line cannot be as-
signed.
Note 2:A station can belong to multiple
groups.•
(1)
(2)YY=00-07: Simultaneous Paging Group 0-
7
00-15: Serial No. within the Group
X-XXXX: Station No.
Assign a Service Restriction Class to each sta-
tion.•
(1)
(2)YY=02
X-XXXX: Station No.
XX
 XX
00-15 : Service Restriction 
Class A
Allow the Service Restriction Class A to page 
the group.•
(1)
(2)YYY=119
00-15: Service Restriction Class A assigned 
by CM12 YY=02
0: Allowed
Assign the access code of paging groups for 
Group Call-2 Way Calling.
Note:Even if an extension does not be-
long to the conference group, the
extension can page the confer-
ence group.•
(1)
(2)Y=0-3 (Tenant Group No.)
X-XX: Access Code
B20: Simultaneous Paging Group 0
B27: Simultaneous Paging Group 7
Assign a Group Call-2 Way Calling key of 
each paging group to the Multiline Terminal, 
if required.
Note:Even if an extension does not be-
long to the conference group, the
extension can page the confer-
ence group.•
(1)
(2)Y=00
X-XXXX: Primary Extension No. +  
+ key No.
F0B20: Simultaneous Paging Group 0
F0B27: Simultaneous Paging Group 7
START
CM56
CM12
CM20
CM15
END
CM90
~ ~
,
~ ~ 
						

							ND-45670 (E) CHAPTER 2
Addendum-001 Page 243-4
JULY, 1998 Revision 2.1
This page is for your notes. 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 44
Revision 2.0
GROUP LISTENING
PROGRAMMING 
DESCRIPTION DATA
Assign the Class of Service for Group 
Listening to the required Multiline 
Terminals.• CM12 YY = 02
[Service Restriction Class B (00-
15 )]
• CM15 YY = 70
(1) Service Rest. class (B) assigned by
CM12 YY = 02 (00-15) 
(2) 0: Allowed
START
END
CM12
CM15 
						

							ND-45670 (E) CHAPTER 2
Page 245
Revision 2.0
HOLD: CALL HOLD
PROGRAMMING 
DESCRIPTION DATA
Assign Service Restriction Class A to the 
required stations.• YY = 02
(1) X-XXXX: Station No.
(2) XX
 XX 
*a: Service Restriction Class A 
(00-15 ) 
Assign this feature to Service Restriction 
Class A assigned by CM12 YY = 02. • YY = 01
(1)  XX: Service Restriction Class A 
assigned by CM12 YY = 02. 
(2) 1 : Allowed
Assign the access code for Call HOLD. • Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX: Access Code (11) 
(2) 046: Call Hold 
Assign a CALL HOLD key to the Multiline 
Terminal, if needed. 
Note:This line key is not the same key nor-
mally assigned to the key labeled
HOLD. That key is normally as-
signed the Non Exclusive/Exclusive
Hold feature.• YY = 00 
(1) Primary Extension No. +   + key No. 
(2) F0046
START
END
CM12
CM15
CM20
CM90*a, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 46
Revision 2.0
HOLD: EXCLUSIVE HOLD
PROGRAMMING
DESCRIPTION DATA
Provide the system with Exclusive Hold.  (1) 130 
(2) 1 : Available
Specify the Recall timing on Exclusive Hold. • Y = 0 
(1) 06
(2) 01-98 : 4-392 sec. in 4 sec. increments
If no data is set, the default setting is 236-240
seconds.
START
END
CM08
CM41 
						

							ND-45670 (E) CHAPTER 2
Page 247
Revision 2.0
HOTLINE
PROGRAMMING 
For internal Hotline:
DESCRIPTION DATA
Assign the Hotline Station to the required 
stations.• YY = 03
(1) X-XXXX (Station No.) 
(2) 04: Hotline Station 
Set up the Hotline pair. Bidirectional 
Hotlines should be assigned as follows:
Note:There is a maximum of 100 assign-
ments for Hotline destination. If in-
ternal bidirectional Hotline calling
is required, two assignments (one
for each direction) must be made. A
maximum of 50 bidirectional Hot-
lines can be assigned. • YY = 00-99 (Hotline Pair No.) 
(1) 0: Calling Side 
(2) X-XXXX (Station No. /Data Station
No. assigned by CM12 YY = 03) 
(1) 1: Called Side
(2) X-XXXX (Station No. /Data Station
No.) 
E00X 
*a: SN610 ATTCON No. 
Specify the result of a Switch Hook Flash on 
each Hotline Station.
To allow Hotline Stations to transfer a call or 
access a feature, set the data to “0”. (1) 057 
(2)  0 : Special Dial Tone Connection 
1 : Attendant Recall
START
END
CM12
CM08
CM52
Hotline Pair No. Calling Side  Called Side
00 Station A Station B
01 Station B Station A 
*a 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 48
Revision 2.0
HOTLINE
For Hotline-Outside:
DESCRIPTION DATA
Assign a Hotline to the required stations. • YY = 03
(1) X-XXXX (Station No.) 
(2) 04: Hotline
Allocate the memory area for the Hotline-
Outside call. For example, to assign the 10 
Hotline-Outside calls into No. 100 through 
No. 109 Memory Slots, 2nd data is 
“100010.” Abbreviated Nos. are 
automatically assigned as shown below:(1) 65: For Hotline-Outside
(2) XXX
 XXX: See left column. 
*a: Starting Memory Slot No. in 
blocks (000-299) 
*b: Number of Memory Slots to be 
assigned in blocks (001-100) 
Set the outside party’s number to each 
Memory Slot No. (1)  XXX: Memory Slot No. (000-299) 
(2)  X...X: Outside Party’s No. (Max. 28 
digits) 
Define the Hotline pairs.  •  YY = 00-99 (Hotline pair No.) 
(1)  0: Calling Station 
1: Called Outside party 
(2)  Station No. (For Calling Station) 
01XX
 (For Called Outside party) 
*a: Abbreviated No. given by CM71.
START
END
CM12
CM52
CM71
CM72Abbrev. 
Memory Slot  00
Memory Slot  09
*b *a
*a 
						

							ND-45670 (E) CHAPTER 2
Page 249
Revision 2.0
HOTLINE
For Brokerage Hotline:
DESCRIPTION DATA
Assign the Virtual Station numbers to the 
required virtual LENs.(1) Virtual LEN (0000-0255) 
(2) X-XXXX (Virtual Station Number) 
Assign the Virtual Station No. assigned by 
CM11 as Hotline.• YY = 03
(1) Virtual Station No. 
(2) 04: Hotline
Define the Hotline pairs.  • YY = 00-99 (Hotline Pair No.) 
(1) 0: Calling party 
(2) Virtual Station No. 
(1)  1: Called party
(2)  Station No. / 
01XX
 (For Outside party) 
*a: Abbreviated No. given by CM71 
(See Hotline-Outside) 
Assign the Virtual Line Station and 
RELEASE keys on the Multiline Terminal. • YY = 00 
(1) Primary Extension No. +   +Key No. 
(2) X-XXXX (Virtual Station No.)
F1020 (Release key) 
START
END
CM11
CM90
CM52
CM12
*a
,