NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 3 92
Revision 2.0
TIMED REMINDER
PROGRAMMING
For providing the internal Music Source for the MP card:
DESCRIPTION DATA
Assign the class of service for Timed Remind-
er to required stations.•  CM12 YY = 02
[Service Restriction Class (A) (00-
15 )] 
• CM15 YY = 13
(1) Service Restriction Class (A) assigned 
by CM12 YY = 02 (00-15)
(2) 1 : Allowed
Assign the access code for Timed Reminder 
set and cancel.• Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code (5*, 5#)
(2) 024: Set
025: Cancel
Designate the type of music source to be con-
nected when answering a Timed Reminder 
call.•Y = 1
(1) 00: Tone source of Timed Reminder
(2) 1400: Hold Tone source on MP card
Assign the Timed Reminder feature access 
key to the Multiline Terminals, if required. • YY = 00
(1) Primary Extension No. +     + Key No.
(2) F0024
Specify the timing for Timed Reminder Start. (1) 228: Timed Reminder Start timing
(2) 0/1 : At preset time/Before 5 minutes 
of preset time
Specify the duration of a Timed Reminder 
Call.•Y = 0
(1) 52:
(2) 01-99: 4-396 sec. in 4-sec. increments
If no data is set, the default setting is 60-64
seconds.CM12
CM20 START
A
CM15
CM48
CM90
CM08
CM41
, 
						

							ND-45670 (E) CHAPTER 2
Page 393
Revision 2.0
TIMED REMINDER
For providing an External Announcement Machine via PN-4COT card:
DESCRIPTION DATA
Specify the number of Timed Reminder at-
tempts before abandonment. (1) 03
(2) 01-05: No. of attempted Timed Remind-
er Calls 
If no data is set, the default setting is 05. 
Specify the maximum number of Timed Re-
minder Calls that can be set at the same time.(1) 04
(2) No. of Timed Reminder Calls. 
If no data is set, the default setting is 10. 
DESCRIPTION DATA
Assign the class of service for Timed Remind-
er to the required stations.• CM12 YY = 02 
[Service Restriction Class (A) (00-
15)]
• CM15 YY = 13 
(1) Service Restriction Class (A) assigned by 
CM12 YY = 02 (00-15 ) 
(2) 1 : Allowed
Assign the access code for Timed Reminder 
set and cancel. •  Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code (5*, 5#) 
(2) 024: Set
025: Cancel 
Assign the PN-4COT card and PN-DK00 card 
to the required LENs.
Note:The PN-DK00 card No. must be as-
signed to the first LEN (Level 0) and/
or the third LEN (Level 2) of each LT
slot. (1) LEN (0000-0511)
(2) DB00: Interface Card for External Tone 
Source 
E800-E831: PN-DK00 Card 
E800-E807: For PIM0/1 
E808-E815: For PIM2/3 
E816-E823: For PIM4/5 
E824-E831: For PIM6/7 
CM42
END
A
A START
CM20
CM10
CM12
CM15 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 94
Revision 2.0
TIMED REMINDER
DESCRIPTION DATA
Assign the function of the PN-DK00 card. (1) XX X: PN-DK00 Circuit No.
 
*a: Last two digits of data assigned by
CM10 (00-31)
*b: Circuit No. (0-3)
(2) 0100: External Announcement Machine 
for Timed Reminder Calling
Assign the Timed Reminder feature access 
key to the Multiline Terminals, if required. • YY = 00
(1)  Primary Extension No. +   + Key No.
(2) F0024
Specify the timing for Timed Reminder start. (1) 228: Timed Reminder start timing
(2) 0/1 : At preset time/Before 5 minutes 
of preset time
Specify the duration of a Timed Reminder 
call.•Y = 0
(1) 52:
(2) 01-99: 4-396 sec. in 4-sec. increments
If no data is set, the default setting is 60-64 
seconds.
Specify the number of Timed Reminder at-
tempts before abandonment. (1) 03
(2) 01-15: No. of attempted Timed 
Reminder calls
If no data is set, the default setting is 05.
Specify the maximum number of Timed Re-
minder calls that can be set at the same time.(1) 04
(2) No. of Timed Reminder calls
If no data is set, the default setting is 10.
CM90
A
CM08
CM41
CM42
END
CM44
*b *a
, 
						

							ND-45670 (E) CHAPTER 2
Page 395
Revision 2.0
TIMED REMINDER
To provide the internal announcement via Digital Announcement Trunk (PN-2DATA):
DESCRIPTION DATA
Assign a Digital Announcement Trunk Circuit 
No. to the required LEN.
Note:The Digital Announcement Trunk
Circuit No. must be assigned to the
first LEN (Level 0) and/or the third
LEN (Level 2) of each LT slot.(1) LEN (0000-0511) 
(2) EB000-EB127: Digital Announcement 
Trunk Circuit No.
For PIM0/1: EB000-EB031  
For PIM2/3: EB032-EB063 
For PIM4/5: EB064-EB095 
For PIM6/7: EB096-EB127 
Assign the Class of Service for Timed Re-
minder set and cancel.• CM12YY = 02
[Service Restriction Class (A) (00-
15 )]
• CM15 YY = 13 
(1) Service Restriction Class (A) assigned by 
CM12 YY = 02 (00-15)
(2) 1 : Allowed
Assign the access code for Timed Reminder 
set and cancel. • Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX: Access Code (5*, 5#) 
(2) 024: Set
025: Cancel 
Designate the type of music source to be con-
nected when answering a Timed Reminder 
call.•Y = 1 
(1) 00: Tone source of Timed Reminder
(2) 0500: Digital Announcement Trunk 
Assign the function of the Digital Announce-
ment Trunk. • YY = 00
(1) XXX: Digital Announcement Trunk Cir-
cuit No. (000-127) assigned by 
CM10. 
(2)  0C
 XX
*a: Answering Message on Timed Re-
minder 
*b: Message No. (00-63) 
•  YY = 08
(1) XX: Tenant No. (00-63) assigned by 
CM10.
(2) XX: Message No. (00-63) 
START
A
CM20
CM48
CM12
CM15
CM10
CM49
*b *a 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 96
Revision 2.0
TIMED REMINDER
DESCRIPTION DATA
Assign the Timed Reminder feature access 
key to the Multiline Terminals, if required. • YY = 00
(1) Primary Extension No. +     + Key No.
(2) F0024
Specify the timing for Timed Reminder start. (1) 228: Timed Reminder start timing
(2) 0/1 : At preset time/Before 5 minutes 
of preset time
Specify the duration of a Timed Reminder 
call.•Y = 0
(1) 23: Timed Reminder call duration
(2) 02-14: 8-56 sec. in 4 sec. increments
If no data is set, the default setting is 28-32
seconds.
Specify the duration of message replay for 
Timed Reminder.•Y = 0
(1) 52
(2) 01-99: 4-396 sec. in 4 sec. increments
If no data is set, the default setting is 60-64
seconds.
Specify the number of Timed Reminder at-
tempts before abandonment.(1) 03
(2) 01-15: No. of attempted Timed 
Reminder calls
If no data is set, the default setting is 05.
Specify the maximum number of Timed Re-
minder calls that can be set at the same time.(1) 04
(2) No. of Timed Reminder calls
If no data is set, the default setting is 10.
To record, replay, or delete a message, assign 
the appropriate Digital Announcement Trunk 
access code.•  Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code
(2) A00: Record
A01: Replay
A02: DeleteCM90
CM08
CM42
A
END
CM41
CM20, 
						

							ND-45670 (E) CHAPTER 2
Page 397
Revision 2.0
TIMED REMINDER
HARDWARE REQUIRED
For providing the Internal Music Source: 
-PN-CP00 card 
For providing the External Announcement Machine: 
-PN-4COT card 
-PN-DK00 card 
External Announcement Machine provided locally.
For providing the internal announcement using a Digital Announcement Trunk: 
-PN-2DATA card ´ 1
To accommodate an External Announcement Machine, make the following connections at the MDF. For details, re-
fer to the MDF cross connection for an External Tone Source in the INSTALLATION PROCEDURE MANUAL.
 
PBX
PN-4COT CARD
PN-DK00 CARDMDF
EXTERNAL ANNOUNCEMENT MACHINE
PZ-PW86 CARD
G
GFOR AMPLIFIER INPUT
FOR CONTROL 
						

							CHAPTER 2 ND-45670 (E)
Page 398 Addendum-002
Revision 2.2 JANUARY, 1999
TRUNK-DIRECT APPEARANCES
PROGRAMMING
DESCRIPTION DATA
Assign the terminating system for required
C.O. Trunks to Trunk-Direct Appearances. • YY=02
(1) 000-255 (Trunk No.) 
(2) 02: Trunk-Direct Appearance 
Provide the Trunk-Direct Appearances fea-
ture to the required C.O. trunk assigned by
YY=02. • YY=18
(1) 000-255 (Trunk No.) 
(2) 0: To be provided 
Assign the Trunk-Direct Appearances key to
each Multiline Terminal, as required.• YY=00
(1) Primary Extension No. +   + Key No. 
(2) D000-D255 (Trunk No.) 
Assign a Hold key for holding the Trunk Di-
rect Appearance call to each Multiline Ter-
minal, as required.
By this assignment, the held Trunk Direct
Appearance call can be transferred by Voice
call, and can be answered by the Trunk Direct
Appearance key on the destination station.
(1800 Series Enhancement)• YY=00
(1) Primary Extension No. +   + Key No. 
(2) F0058 
Specify whether a Dial Tone is sent when the
call is held by the Hold key for Trunk Direct
Appearance (CM90 YY=00 (2) F0058).
(1800 Series Enhancement)(1) 365 
(2) 0 : Sent
1 : Not sent
Specify whether Hold Transfer for a trunk
line placed in Consultation Hold is available
or not available.(1) 161 
(2) 0 : Available (Hold Transfer)
1 : Not Available (Consultation 
Hold)CM30
CM90 START
CM08
END
,
, 
						

							ND-45670 (E) CHAPTER 2
Page 399
Revision 2.0
TRUNK-DIRECT APPEARANCES
To provide enhanced Trunk-Direct Appearance:
Note:If the incoming call is routed via the Internal Automated Attendant feature (PN-2DATA card), the tenant number pro-
grammed in CM49, YY=01 must match the tenant number programmed in CM20, YY=01 for the incoming trunk.
HARDWARE REQUIRED 
Multiline Terminal and DLC card
PN-4COTB / PN-COTG
DESCRIPTION DATA
Program enhanced Hold key to each Dterm.
Program Trunk Answer key.• YY = 00
(1) X-XXXX,24: Station No., Button No.
(2) F0058: Enhanced Hold Key
(1) X-XXXX,XX: Station No., Button No.
(2) F0059: Trunk Answer Key
Assign Trunk Answer code to be used for 
analog telephones.
Assign Trunk Hold code to be used for 
analog telephones.•Y = 0-3
(1) X-XXX: 1-3 digit access code
(2) 059: Trunk answer code
•Y = 0-3
(1) X-XXX: 1-3 digit access code
(2) 058: Trunk hold code
Assign ID code for each C.O. trunk • YY = 19
(1) 000-255: Trunk number
(2) ABCD: 4-digit Trunk ID code
Assign Answer preference. (1) 114
(2) 1: Answer by 4-digit Trunk ID code
[Answer Code + Trunk ID Code 
(ABCD)]
0: Answer by 2-digit Trunk ID code
[Answer Code + Trunk ID Code 
(CD)]
Assign Hold Recall to alternate destination. • YY = 21
(1) 00-63: Tenant number
(2) X-XXXX:Station No. or SN-610
Console
START
END
CM90
CM20
CM30
CM08
CM51 
						

							CHAPTER 2 ND-45670 (E)
Pag e 4 00
Revision 2.0
TRUNK-DIRECT APPEARANCES
The table below shows the availability of the HOLD key (CM90 YY=00 2nd data: F0058) on each condition.
HARDWARE REQUIRED 
Multiline Terminal and DLC card.
Trunk-Direct
Appearances
(CM30 YY=18)Trunk ID Code 
Assignment
(CM30 YY=19)Kind of 
TrunksTrunk ID Code DisplayAvailability of HOLD Key
(CM90 YY=00 2nd Data: F0058)
0 (Provided) – – – Available
1 (Not provided) Not assigned – – Not available
Assigned CCIS trunk – Not available
ISDN trunk CM35 YYY=146 is set to 0.
(Trunk ID Code is displayed.)Av a i l a b l e
CM35 YYY=146 is set to 1.
(Calling/called sub-address is displayed)Not available
Other trunks CM35 YY=75 is set to 0.
(DID incoming LDN is displayed.)Not available
CM35 YY=75 is set to 1.
(Trunk ID Code is displayed.)Av a i l a b l e 
						

							ND-45670 (E) CHAPTER 2
Page 401
Revision 2.0
TRUNK QUEUING-OUTGOING
PROGRAMMING
DESCRIPTION DATA
Assign the class of service for Trunk Queuing-
Outgoing to the required stations.• CM12 YY = 02 
[Service Rest. Class (A) (00-15 )] 
• CM15 YY = 02 
(1) Service Restriction Class (A) (00-15) as-
signed by CM12 YY = 02
(2) 1 : Allowed 
Assign the access code for setting and reset-
ting this service.• Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX: Access Code (*1, #1) 
(2) • If a different access code from Call 
Back is used. 
000: Set 
001: Reset
• If the same access code as Call Back is 
used. 
004: Set 
005: Reset
Assign the Trunk Queuing-OG (Call Back) 
key to the required Multiline Terminal. • YY = 00
(1) Primary Extension No. +   + Key No.
(2) F0004 
Specify the Trunk Queuing-Outgoing capabil-
ity for each trunk route. • YY = 28
(1) XX (Trunk Route No. 00-63) 
(2) 0/1 : Restricted/Allowed 
CM20
END
START
CM35
CM90
CM12
CM15
,